User Manual
Table Of Contents
- 1. Product Introduction
- 2. Quick Deployment Guide
- 3. Assemble the Device
- 4. Configure the Device to Connect to SenseCAP Cloud Platform
- 5. Add a Custom Sensor
- 6. Troubleshooting and Log Analysis
- 7. Do’s & Don’ts
User Manual
© 2008-2021 Seeed Technology Co., Ltd. All rights reserved. solution.seeedstudio.com
Page 39 of 45
# HW VER: 3.1.0
# CLOUD:1
# EUI:2CF7F16924410088
# APPKEY: 656A1B1A98EA1846037A1FA34A831572
# PERIOD:5min
# SWITCH:[GPS:0, OTA:0, INFO OTA:0, LOG:1]
# Unsent packet: 0
Detect net module... Detected EC25 module
elsepse: 12s.
register network ok,elsepse: 14s. // Successful networking
[2021/03/08 17:04:07]
syn time successful // Synchronization time was successful
Check the list of sensor information
[2021/03/08 17:04:07] Check that the sensor infor is up to date...
This is the latest info, ver:2!
=================================
sinfo list: total:36 => [1,2,3,4,5,6,7,8,9,10,12,13,14,15,16,17,18,19,20,21,22,24,25,26,27,28,29,30,31,32,33,34,35,36,37,128,]
En list: total:36 => [1,2,3,4,5,6,7,8,9,10,12,13,14,15,16,17,18,19,20,21,22,24,25,26,27,28,29,30,31,32,33,34,35,36,37,128,]
Scan the channel information for the data collector:
Scan port: 1 //channel 1, Port 1 on Sensor Hub
[! Finds RS485 device addr:128 in port1 // Discover the Modbus address of 128 sensor in channel 1
[! News Save new sensor addr: 128 to channel 13 // Store Modbus address 128 sensor in channel 13
=================================
Scan port: 2
=================================
Scan port: 3
=================================
Scan port: 4
Constant-power Sensor information:
5V UPS num:0, 12V UPS num:0, list:
port1 UPS power:
port2 UPS power:
port3 UPS power:
port4 UPS power:
Channel usage status, the channel number is the main channel + sub-channel, the measured value of the sensor carries this
numeric as the identification number
<Channel status
channel: 10, saddr:20, sensorID:0x0000, status: IDLE /channel 10 for primary channel 1, subchannel 0;
channel: 11, saddr: 130, sensorID: 0x0000, status: IDLE
channel: 12, saddr: 131, sensorID: 0x0000, status: IDLE
channel: 13, saddr:128, sensorID:0x6000, status: NORMAL // In channel 1 of the collector is connected to a sensor with
address 128, sensor ID is 0x6000, in good condition
channel: 14, saddr: 0, sensorID: 0x0000, status: IDLE
channel: 15, saddr: 0, sensorID: 0x0000, status: IDLE
channel: 16, saddr: 0, sensorID: 0x0000, status: IDLE
channel: 17, saddr: 0, sensorID: 0x0000, status: IDLE
channel: 18, saddr: 0, sensorID: 0x0000, status: IDLE
channel: 19, saddr: 0, sensorID: 0x0000, status: IDLE