EMB1061 Datasheet BLE module Vision：1.3 Date：2018-12-03 Number: DS0080EN Abstract ⚫ Features ⚫ Based on an ultra-low power BLE SOC ▪ ARM Cortex-M0 Core 32MHz ▪ 24KB RAM ▪ 160KB Flash ⚫ Operating Voltage: 1.7V～3.6V ⚫ Bluetooth Features ▪ Support Bluetooth 4.
Datasheet [Page 1] Version history Date Vision 2017-04-07 0.1 Details Initial release 1. Update pin definition 2017-05-21 0.2 2. Update power consumption 3. Update RF data 2017-07-04 1.0 Update pin definition 2017-07-05 1.1 Update RF data 2018-03-08 1.2 Update operation temperature 2018-12-03 1.
Datasheet [Page 2] Content Abstract ............................................................................................................................................................................... 1 Version history .................................................................................................................................................................... 1 1. Product Introduction ........................................................................................
Datasheet [Page 3] Figure 7 EWB1061 mechanical size (Unit: mm) ............................................................................................... 15 Figure 8 Humidity Card ..................................................................................................................................... 16 Figure 9 Storage Condition ................................................................................................................................
Datasheet [Page 4] 1. Product Introduction EMB1061 is an embedded BLE module by MXCHIP. It integrates a BLE4.2 single mode SOC, including ARM Cortex-M0 Core, BLE/2.4G Radio, 24KB RAM, 160KB Flash and rich peripherals. EMB1061 uses half-hole package which is easy for soldering. Hardware diagram is shown below with three main parts: ⚫ 32-bit Cortex-M0 Core ⚫ BLE 2.4GHz RF ⚫ Power management With: 1. Up to 16MHz ARM Cortex-M0 MCU with 24KB RAM , 160KB FLASH, UART，I2C，SPI，ADC， Timer/PWM 2.
Datasheet [Page 5] EMB1061 appearance Figure 1 EMB1061 appearance Pin Arrangement EMB1061 has 22 pins, with 2.0mm pin pitch. EMB1061 uses half-hole package (as shown in figure 2, figure3) , which could effectively reduce the quality risk of SMT re-flow. Solder mask openness has the same size with land. The width of steel mesh is suggested to be 0.12mm to 0.14mm in SMT.
Datasheet Figure 2 EMB1061 PIN assignment Figure 3 EMB1061 mechanical size EMB1061 [Page 6]
Datasheet [Page 7] Pin Definition 1.3.1 EMB1061 Package Definition Figure 4 EMB1061 Package Definition 1.3.2 EMB1061 Pin Definition Table 1 EMB1061 Pin Definition NO.
Datasheet [Page 8] NO.
Datasheet [Page 9] 2. Electrical Parameters Operating Conditions EMB1061 would be unstable when input voltage is less than the lowest rated voltage. Table 2 Range of input voltage Details Symbol Illustration Condition Minimum Typ Maximum Unit 1.7 3.3 3.6 V Power Supply VDD There would be permanent damage in hardware if the device operates at the voltage over rated value. Meanwhile, reliability could be influenced when the device has a long-term operating at maximum voltage.
Datasheet Mode [Page 10] Description Average Max TA=25°C TA=25°C 3.54uA 2.76mA 375.98nA 2.68uA TIMER_SLEEP mode between the scan intervals. TIMER_SLEEP ON CPU and all peripherals OFF, internal slow RC clock and wakeup Sleep pins ON Can be waked up by internal RTC or wakeup pins（IO9/10/11/12/13）. Wake up every 10s in this test. CPU and all peripherals OFF Wakeup pins ON Standby Can be waked up by wakeup pins （IO9/10/11/12/13）. Actual working current is variable at different operating mode.
Datasheet [Page 11] 3. RF parameters Basic RF parameters Table 7 Radio-frequency standards Name Illustration Working frequency 2.4GHz ISM band Wi-Fi wireless standard Bluetooth4.2 Modulation FSK/GFSK Data rate 250Kbps-2Mbps PCB (Default) Antenna type IPEX Connector (Optional) FSK/GFSK Parameters Table 8 FSK/GFSK mode parameters Item Notes Modulation FSK/GFSK Frequency range 2.400GHz-2.
Datasheet [Page 12] 4. Antenna Information Antenna Type EMB1061 has two types of antenna: PCB antenna (EMB1061-P), IPEX connector (EMB1061-E). Figure 5 EMB1061-P Figure 6 EMB1061-E PCB Antenna Clearance Zone Main PCB should have a distance over 16mm with other metal elements when using PCB antenna in Wi-Fi device. Shadow parts in the figure below should keep away from metal elements, sensor, interference source and other material that could cause signal interference.
Datasheet Figure 5 Minimum Clearance Zone of PCB Antenna (Unit: mm) EMB1061 [Page 13]
Datasheet External Antenna Connector Figure 6 Size of External Antenna Connector EMB1061 [Page 14]
Datasheet [Page 15] 5. Assembly Information and Production Guidance Assembly Size Figure 7 EWB1061 mechanical size (Unit: mm) Production Guidance（Important） ⚫ The stamp hole package module produced by Mxchip must completely being patched by SMT machine in 24 hours after open firmware package. Otherwise the module should be re-package by vacuum pumping and drying before patch.
Datasheet [Page 16] （2）Anti-static and high thermos tolerant tray （3）Anti-static and high thermos tolerant gloves ⚫ Conditions of product storage (Storage environment is shown in figure 8): ▪ Moisture bag must be stored in temperature below 30 and humidity less than 85%RH. ▪ Dry packaging products, the guarantee period should be from 6 months date of packing seal. ▪ Humidity indicator card is in the hermetic package.
Datasheet [Page 17] corresponding responsibility; ⚫ ESD protection is required before SMT; ⚫ SMT patch should on the basis of reflow profile diagram, maximum temperature 245℃, reflow profile diagram is shown in figure 10; ⚫ In order to guarantee the reflow soldering qualification rate, vision and AOI detection should be done in 10% products for the first patch to make sure the rationality of temperature control, device adsorption mode and position.
Datasheet Storage Condition Figure 9 Storage Condition EMB1061 [Page 18]
Datasheet [Page 19] Temperature Curve of Secondary Reflow Suggested solder paste type: SAC305, unleaded, solder paste thickness from 0.12 to 0.15, less than 2 times reflow.
Datasheet [Page 20] 6. Reference Circuit Power source circuit is shown in figure 11, USB to UART is shown in figure 12, external interface circuit is shown in figure 13.
Datasheet [Page 21] Figure 13 External Interface Circuit of EMB1061 Voltage of EMB1061 UART is 3.3V. 5V UART should convert to 3.3V UART for the users that have 5V chips. Convert circuit is shown in figure 14. Figure 14 3.
Datasheet [Page 22] 7.
Datasheet 8. Sales Information and Technical Support For consultation or purchase the product, please contact Mxchip during working hours: From Monday to Friday, morning 9:00~12:00, afternoon 13:00~18:00 Telephone: +86-21-52655026 Contact address: 9thFloor, No.5, Lane2145 JinshaJiang Road Putuo District, ShangHai. Postcode：200333 Email: sales@mxchip.
