# LoRaWAN Gateway Kit LoRa is a perfect long-range w ireless solution to create low -pow er, w ide area netw orks.So far w e have released several “LoRa” boards such as Seeeduino LoRaWan and Grove LoRa Radio etc. How ever if you w ant to build you ow n LoRa netw ork, there are 3 things that you should prepare to get started: a Gatew ay, at least one Node and a local server w here you can monitor all your devices.
Partlist Parts number Parts name Quantity ❶ Raspberry Pi 3 1 PCS ❷ Gateway module RHF0M301–868 1 PCS ❸ PRI 2 Bridge RHF4T002 1 PCS ❹ Seeeduino LoRaWAN with GPS (RHF76-052AM) 1 PCS ❺ USB to UART Adapter 1 PCS ❻ upgrade to 16GB Micro SD Card – Class 10 1 PCS ❼ 0dBi Rubber Duck Antenna 1 PCS ❽ 5V/2.
⓫ RJ45 Ethernet Cable 200cm 1 PCS ⓬ JST2.0 Cable 10cm 1 PCS Application Ideas Internet of Things Smart House Security Smart Grid Intelligent Farm Intelligent Park Getting Started Hardware Interfaces overview Since there are many interfaces here, it is necessary to know the capabilities of these interfaces. Please refer to the follow ing figure for details. ❶ Micro-USB Input: The w hole system use this Micro-USB interface for pow er supply.
❹ HDMI: HD digital video output interface. ❺ Headphone jack: 3.5mm Headphone jack ❻ Ethernet interface: You can use the Ethernet interface to connect this system to the Internet. Or you can use Wifi after you configured the w ireless netw ork. Hardware connection Step 1. Plug Gatew ay m odule RHF0M301–868 into PRI 2 Bridge RHF4T002. Step 2. Plug PRI 2 Bridge RHF4T002 into Raspberry Pi 3. Step 3. Connect ❷ and ❸ via the 20cm Micro-USB cable. Step 4.
Software Software Tool In the follow ing guide, below tools w ill be needed, please install it to your computer. Arduino, portable serial tool, used to open the serial port of Seeeduino LoRaWAN w ith GPS (RHF76-052AM) and send AT commands to it. PuTTY, terminal tool include both serial and SSH terminal, used to control Raspberry Pi. Internet brow ser, used to access RHF2S001 integrated LoRaWAN server (It is recommended to use Chrome or Firefox).
d) Pow er the gatew ay up. Booting log w ill be show ed in the PuTTY terminal, in the end it w ill prompt you to input your log in name. Please note it takes 1 or 2 minutes to get the prompt information.
e) Please use RHF2S001 default user name and passw ord to log in. ( Username: rxhf, Passw ord: risinghf ). Note, w hen input the passw ord, there is no any echo f) Connect RHF2S001 w ith router through ethernet cable g) Run ifconfig to check the ip address and mac address. IP is in the blue square, MAC address is in orange square (Form at: b8:27:eb:xx:xx:xx) Note A fter y ou get the IP, it is recommended to login RHF2S001 again through SSH.
stable. We normally use serial tool to get the IP. Reopen PuTTY , use the SSH module to connect again. To login through SSH, you need to fill in the Hostname w ith the IP address you've just got.And use port 22,choose the SSH connection type. Just leave the other options by default. Then simply click Open. Step 2. Expand SD Card File System By default, the image enables only 2GB for Raspbian System, it is recommended to expand to use the w hole SD card (8GB or 16GB). Or the SD card w ill be full soon.
CH2 902.7 DR0 ~ DR3 CH3 902.9 DR0 ~ DR3 CH4 903.1 DR0 ~ DR3 CH5 903.3 DR0 ~ DR3 CH6 903.5 DR0 ~ DR3 CH7 903.7 DR0 ~ DR3 CH64 903.0 DR4 c) RHF76-052AM Settings Now let's configure the Seeeduino LoRaWAN w ith GPS (RHF76-052AM). Firstly, you need to connect Seeeduino LoRaWAN GPS to your PC. Secondly, open the Arduino IDE, and copy the code blew into a new skech. void setup() { Serial1.begin(9600); SerialUSB.begin(115200); } void loop() { while(Serial1.available()) { SerialUSB.
Now please open the serial monitor in the upper right corner ( or you can press Ctrl+Shift+M at the same time ).Choose New line (This option w ill add "\r\n" at the end of each command.), set the baud rate 9600.Then tap the commands below and press send. For EU868 AT+FDEFAULT=RISINGHF AT+DR=EU868 For US915 AT+FDEFAULT=RISINGHF AT+DR=US915HYBRID AT+RXWIN2=923.
Caution A fter y ou plug Seeeduino LoRaWA N with GPS into y our computer, y ou may find two serial Ports. One is for raspeberry with putty , one is for Seeeduino LoRaWA N GPS with SSCOM, please choose the right one. d) Access Internal Server Console Fill your brow ser w ith the IP address![]()(IP of your gatew ay) ,it Will jump to the w ebsite below . Step 4.
There are tw o modes,in this w iki w e only talk about the ABP Mode(This Mode is free for anyone),for more information about OTAA Mode(This model is commercial, you need to pay for it),you can click here. a) Find the "Application" button in the upper right corner of the w ebsite above, click it and you w ill see a new page. b) Now you need APPEui,DevAddr,DevEui of Seeeduino LoRaWAN to add a new application.
Then you w ill jump into the configure page. In this page, w e choose Personalised Motes. Fill in the DevEUI and DevAddr w ith ID info. of your Seeeduino LoRaWAN GPS. And set the NWKSKEY and APPSKEY by default. You can refer to the picture below .
Then turn to the w ebsite, click Application->Seeed(the nam e of the Application you just added)->View application data, you w ill see the data you've just sent form the Seeeduino_LoRAWAN. congratulations! Job done! Connect To Loriot Server Step.1 Loriot Server Gateway Registration a) New user need register an account first, click registration address .
b) After successful activation, click here to log in. Default tier is “Community Netw ork”, it supports 1 Gatew ay (RHF2S001) and 10 nodes. c) Enter Dashboard -> Gatew ay, click Add Gatew ay start to add Gatew ay. d) Select Raspberry Pi 3 e) Set as below : Radio front-end -> RHF2S001 868/915 MHz(SX1257) BUS -> SPI f) Fill in the MAC address of your RHF2S001, should be in format of b8:27:eb:xx:xx:xx. And also input Gatew ay Location information.
Step 2. Loriot Server Connect Node device a) Get the available gatew ay channels Current gatew ay channels could be got from Dashboard -> Gatew ay -> Your Gatew ay , you can see the available channels as the picture below . b) Seeeduino LoRAWAN GPS(RHF3M076) Configuration Open the serial monitor of Arduino IDE, tap the command below .
To confirm the default channel of your Seeeduino_LoRAWAN GPS, you w ill get 3 channels. If there is no available channel, you can change the channels of Seeeduino_LoRAWAN by the command below . at+ch=0,868.1 at+ch=1,868.3 at+ch=2,868.5 Then you can use at+ch again to check. c) Add Seeeduino_LoRAWAN GPS as an ABP Node Log in Loriot server , Click Dash Board->Applications->Sim pleApp .
d) Send data from Seeeduino_LoRAWAN Back to serial monitor of Arduino IDE, send command: AT+CMSGHEX="0a 0b 0c 0d 0e" Then go to Dashboard -> Applications -> Sam pleApp ->Device , click the Node Device EUI or DevAddr, you w ill find the data you've just sent here. . FAQs Please click here to see all LoRa/LoRaWAN Gatew ay Kit FAQs. Tech support Please do not hesitate to contact techsupport@seeed.cc if you require further information.
[PDF] Dow nload Wiki PDF [Uer Manual] User Manual.
