LCM Specification ( )Preliminary Specification ( ) Final Specification PRODUCT TYPE: PRODUCT P/N: VERSION: U HXWY TFT MODULE WTIMV101H-02 V0 Customer DESIGNED BY INSPECTION RESULT CHECKED BY TESTED BY APPROVED BY APPROVED BY .
Revision Description Notice 0.0 First revision (Tentative) Page Rev. Date -- 2017/06/02 .
TABLE OF CONTENTS NO. CONTENTS PAGE REVISION STATUS ................................................................................................................................... 2 TABLE OF CONTENTS ............................................................................................................................ 3 1. GENERAL DESCRIPTION .................................................................................................................... 4 2. MECHANICAL SPECIFICATION ........
1. GENERAL DESCRIPTION 1.1 DESCRIPTION WTIMV101H-02 is a color active matrix thin film tr ansistor (TFT) IPS liquid crystal display (LCD) that uses amorphous silicon TFT as a switching device. It is composed of a TFT LCD panel, Driver IC ,FPC and Backlight. 1.2 FEATURES: No. Item Specification Unit 1 Panel Size 10.1” inch 2 Number of Pixels 3 Active Area 135.360(W)x216.576(H) mm 4 Pixel Pitch 0. 1692 x 0.1692 mm 5 1200x3(RGB) x 1920 OutlineDimension pixels 228.6( W) x 143(H) x2.
2. MECHANICAL SPECIFICATION 1 2 (71.48) 3 *143±0.3 135.36( A,A) DATE 日期 DESCRIPTION 修 改 内 容 *2.33±0.2 电路图 REVISER 修 改 者 6 (49.45) 7 DESIGNED 制 定 者 CHECK 核 对 APPROVED 承 认 量产图 1/1 插接方向 +- 17.05.22 A0 PAGE 页 次 LCM DATE 日 期 EDITION 版 本 号 WTIMV101H-02 WTIMV101H-02 TYPE 类 型 PART NO. 料 号 MODEL NO. 模 组 号 8 第三视角 . 深圳市启明云端科技有限公司 (111.62) NOTES: 1. DISPLAY TYPE: 10.1"; 2. VIEWING DIRECTION: IPS ; 3. LCM Chromaticity(White): X 0.31+/-0.03;Y 0.32+/-0.03; 4.
3. PIN DESCRIPTION Symbol Description PIN NO. 1 NC 2 VDD Power Voltage for digital circuit 3.3V 3 VDD Power Voltage for digital circuit 3.
31 LED- LED Cathode 32 LED- LED Cathode 33 NC No connection 34 NC No connection 35 36 NC NC No connection No connection 37 NC No connection 38 39 NC LED+ No connection LED Anode 40 LED+ LED Anode 4. Absolute Max. Rating Item Symbol Power Voltage VCC Backlight forward current ILED Input Signal Voltage VI Operation Temperature TOP Storage Temperature TST 4.1 Typical Operation Conditions Item Symbol Values Min. Max. -0.3 +5.0 0 25 -0.
5. Signal timing diagramPower Sequence 5.1 Power on .
5.2 Power off .
5.3 MIPI Timing characteristics 5.4 MIPI Lane Configuration .
6. MIPI AC Electrical characteristics 6.1High Speed Transmission .
6.2 LP Transmission LOW Power Mode .
. P/N: WTIMV101H-02 VERSION:V1 Page 13
6.3 DSI Bursts .
6.4 Reset Input Timing .
6.5 Deep Standby Mode Timing 6.6 DC Characteristics for DSI HS Mode .
7. Optical Specifications Item Symbol θL Viewing angle (CR≥ 10) Color chromaticity Luminance Luminance uniformity Φ=180° (9 o’clock) Φ=0°(3 o’clock) Φ=90° (12 o’clock) Φ=270° (6 o’clock) Min. Values Typ. Max. Unit Remark degre e Note 1 - 80 - - 80 - - 80 - - 80 - TRT - 20 30 msec Note 3 CR WX 600 0.272 800 0.302 0.332 - 0.291 0.321 0.
Note 1: Definition of viewing angle range Normal θ=Φ=0° line Φ=90° 12 o’clock direction θL θB θT θR Φ=180° Φ=0° Active Area LCM Φ=270° 6 o’clock direction Fig. 4-1 Definition of viewing angle Note 2: Definition of optical measurement system. The optical characteristics should be measured in dark room. After 30 minutes operation, the optical properties are measured at the center point of the LCD screen. (Viewing angle is measured by ELDIM-EZ contrast/Height :1.
detector output intensity changed from 10% to 90%. Fig. 4-3 Definition of response time Note 4: Definition of contrast ratio Note 5: Definition of color chromaticity (CIE1931) Color coordinates measured at center point of LCD. Note 6: All input terminals LCD panel must be ground while measuring the center area of the panel. The LED driving condition is ILED=140mA. Note 7: Definition of Luminance Uniformity Active area is divided into 9 measuring areas (Refer to Fig. 4-4 ).
