User's Manual

ManualsBrandsSEECODE ManualsAudio EquipmentBluetooth Headset

SEECODE DOC VER 20041229.0.93.AIDfduj7839fduTHDOCTHOIO - 876YUIF

Bluetooth

Headset

VIM

a User’s Guide

SEECODE DOC VER 20041229.0.93.AIDfduj7839fduTHDOCTHOIO - 876YUIF

Disclaimer

MODEL : VSH411

The headset described in this guide is approved to be

compliant with the Bluetooth

Specification and its

profiles.

is a trademark owned by Bluetooth SIG.

All brand names are the property of their respective

owners.

FCC ID RPRVSH411

* Section 15.19 Labelling requirements

This device complies with part 15 of the FCC rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference and

(2) This device must accept any interference received,

including interference that may cause

undesired operation.

* Section 15.21 Information to user

The changes or modifications not expressly approved by

the party responsible for compliance could void the user’s

authority to operate the equipment.

Summary of content (10 pages)

PAGE 1
Bluetooth® Headset Disclaimer VIM MODEL : VSH411 a User’s Guide The headset described in this guide is approved to be compliant with the Bluetooth® Specification and its profiles. is a trademark owned by Bluetooth SIG. All brand names are the property of their respective owners. FCC ID RPRVSH411 * Section 15.19 Labelling requirements This device complies with part 15 of the FCC rules.
PAGE 2
* IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate the device. Table of Contents DISCLAIMER ............................................................................................. 2 I. INTRODUCTION........................................................................5 II.
PAGE 3
adjust volume, without touching your mobile device. I. Introduction The VSH411 headset is a wireless headset based on Bluetooth® technology. Bluetooth® technology is a standard for short range radio communications. Your Bluetooth® phone and headset do not need to be in a line of sight. The two devices only need to be within a maximum of 10 meters of each other, although the connection can be subject to interference from obstacles, such as walls, or from other electronic devices.
PAGE 4
Earphone II. Getting started Volume down button Charger connector In the package Ear hook Microphone The VSH411 Bluetooth® headset package contains : Volume up button the headset, Talk / Power button and the LED indicator a charging cable, two changeable upper deco housings in different colors and this manual. Charging the battery To charge the battery, simply connect the charger cable Overview to the headset. And then, connect the charger to an AC 2 wall outlet.
PAGE 5
To switch on : press and hold the talk/power button for 2 or 3 seconds. The headset plays its booting melody and the green indicator light starts blinking Wearing the headset Notice : If battery level is too low to power on when you You can put on the VSH411 Bluetooth® headset on either ear. switched the headset on, it plays four tones in a row and will not be switched on. You should charge the headset and then, you can switch it on.
PAGE 6
III. Using the headset Switch on the headset Press the volume up and volume down buttons Making a call simultaneously. Make a call using your mobile phone. You can hear the headset plays its pairing tone. The The voice is transferred to the headset by pressing on LED indicator light blinks rapidly. Now, the headset is in the talk button of your headset.
PAGE 7
phone through the earphone of the headset. Say the desired name(voice tag) to the headset's microphone. Transferring the call from the headset to the The device will dial the number associated with the voice phone tag. Please refer to your mobile's user manual. Ending a call Transferring the call from the phone to the To end a call, press the Talk button while there is an headset ongoing call. While an ongoing call is in progress with your phone, press the talk button on your headset.
PAGE 8
IV. For advanced users which is a voice channel, is established. The phone's audio is redirected to your headset through the voice Headset connection states channel("SCO" channel of the Bluetooth). There is several states in the headset in accordance with its connection status to the phone. The LED indicating light reflects the headset's connection state. In the "waiting" state, any paired device can connect to the headset.
PAGE 9
More about pairing procedure Before the headset can be used with your phone, the Connecting and disconnecting two devices phone has to be paired with the headset. The headset First, connecting. This can be done by using the can be paired with up to 3 phones. It can be connected respective function in your phone. Also, the headset can to only one phone at a time, however. connect to its "default device" by pressing the talk button.
PAGE 10
simultaneously while the headset is in its pairable mode. V. Specification This will erase all the information about paired devices. You need to pair the headset with your phones again to use it with your mobiles. SEECODE DOC VER 20041229.0.93.AIDfduj7839fduTHDOCTHOIO - 876YUIF item value Operating Temperature 0 ~ 60 Storage Temperature -20 ~ 80 Power Consumption Max 42mA Operating Voltage 3.5Vdc ~ 4.2Vdc, 3.7Vdc normal Standby Time 200 hours Talking Time 3.