ST-IP2PTZC QUICK START GUIDE www.nacebrands.com www.securitytronix.
ST-IP2PTZC QUICK START GUIDE Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the dealer. This manual applies to Securitytronix Compact PTZ network cameras. This manual may contain several technical incorrect places or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual. We will readily improve or update the products or procedures described in the manual.
ST-IP2PTZC QUICK START GUIDE Regulatory Information FCC Information FCC compliance: This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
ST-IP2PTZC QUICK START GUIDE Safety Instruction These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss. The precaution measure is divided into Warnings and Cautions: Warnings: Neglecting any of the warnings may cause serious injury or death. Cautions: Neglecting any of the cautions may cause injury or equipment damage. Warnings Follow these safeguards to prevent serious injury or death.
ST-IP2PTZC QUICK START GUIDE Exposing the equipment to direct sun light, low ventilation or heat source such as heater or radiator is forbidden (ignoring this can cause a fire hazard). Do not aim the speed dome at the sun or extra bright places. A blooming or smear may occur (which is not a malfunction), and affecting the endurance of the sensor at the same time.
ST-IP2PTZC QUICK START GUIDE Table of Contents 1 Overview ...................................................................................................... 6 2 Installation ................................................................................................... 7 2.1 Wall Mounting ......................................................................................................... 7 2.2 In-ceiling Mounting..................................................................................
ST-IP2PTZC QUICK START GUIDE 1 Overview Please turn the power off before connect the cables. The cable interfaces of the network speed dome are shown in the following figure. The cables are distinguished by different colors. The labels attached on the cables are for identification. 1 V AC24 EN RE V OW/G AC24 YELL RED GREEN/WHITE RED/WHITE BLUE/WHITE AUDIO_GND AUDIO_IN AUDIO_OUT K BLAC 2 3 Figure 1-1 Overview Table 1-1 Overview No.
ST-IP2PTZC QUICK START GUIDE 2 Installation Before you start: Check the package contents and make sure that the device in the package is in good condition and all the assembly parts are included. Note: Do not drag the speed dome with its waterproof cables as shown in Figure 2-1, otherwise the waterproof performance is affected. Figure 2-1 Do Not Drag the Cables 2.1 Wall Mounting Steps: 1. Loosen the two lock screws as shown in the following figure. 2. Remove the lower dome.
ST-IP2PTZC QUICK START GUIDE Protective sticker protectivefoam Figure 2-3 Disassemble the Speed Dome 5. Drill four M8 screw holes on the wall according to the screw holes of the wall mount. 6. Secure the wall mount to the wall with screws. Notes: For cement wall mounting, you need to use the expansion screw to fix the mount. The mounting hole of the expansion pipe on the wall should align with the mounting hole on the mount.
ST-IP2PTZC QUICK START GUIDE 9. Loosen the lock screws of the adapter. ② ① Top View of Pendant Adapter Lock Screw Pendant Adapter Lock Screw Figure 2-5 Install the Pendant Adapter 1 Note: The dimension of pendant adapter is G12. 10. Hook the two ends of the safety rope to the back box of the speed dome and the wall mount respectively. Route the cables through the mount. 11. Align the direction label of pendant adapter with the label of the back box to install the speed dome as shown below.
ST-IP2PTZC QUICK START GUIDE Lock Screw Figure 2-7 Tighten the Lock Screws 2.2 In-ceiling Mounting Before you start: The in-ceiling mounting is applicable to indoor ceiling construction. The following are the mandatory preconditions for mounting: The height of the space above the ceiling must be more than 250mm. The thickness of the ceiling must ranges from 5 to 40mm. The ceiling must be strong enough to withstand more than 4 times the weight of the dome and its accessories. Steps: 1.
ST-IP2PTZC QUICK START GUIDE Note: ±2mm of the diameter of the circle is tolerable. Φ 224 Figure 2-9 Draw and Cut a Hole on the Ceiling 5. Connect the cables. The cables have been connected to the corresponding interfaces. Connect the power cable and the red LED indicator turns on when the power is on. Note: Please turn the power off after checking the speed dome. 6. Install the speed dome to the ceiling. Steps: 1).
ST-IP2PTZC QUICK START GUIDE Ceiling Lock Lock Screw Figure 2-11 Install the back box 7. Install the trim ring. Steps: 1). Attach the trim ring to the lower dome and align the triangular notch of the trim ring with the arrow label on the in-ceiling mount. 2). After having firmly placed the trim ring to the ceiling, rotate the trim ring in the direction of arrow to secure the trim ring in place. Notes: Please remove the protective film on the lower dome after the installation is finished.
ST-IP2PTZC QUICK START GUIDE The ceiling must be strong enough to withstand more than 4 times the weight of the dome and its accessories. 2.3.1 Wiring For Ceiling Mounting Applications The cables of the dome can be routed either from the top or the side of the back box, as shown in Figure 2-13. For the cables routed from the top of the back box, it is required to drill a cable hole in the ceiling. Figure 2-13 Cabling for Ceiling Mounting 2.3.
ST-IP2PTZC QUICK START GUIDE 5. If you route cables from the top of the back box, mark the cable hole on the ceiling and drill a hole. 6. Secure the mounting base to the ceiling with set screws. Screw Holes Cable Hole Figure 2-15 Mark the Screw Positions If the speed dome is installed to a wooden wall, use the self-tapping screws to secure the mounting base.
ST-IP2PTZC QUICK START GUIDE Push forwards Line up Push upwards Spring Lock clip Figure 2-16 Attach the Back Box to the Mounting Base Notes: Please remove the protective film on the lower dome after the installation is finished. Do not touch the bubble of the lower dome directly by hand. The image blurs otherwise.
ST-IP2PTZC QUICK START GUIDE 3 Setting the Dome over the LAN To view and configure the speed dome via LAN(Local Area Network), you need to connect the network speed dome in the same subnet as your PC. Then, install the SADP or client software to search and change the IP of network speed dome. The following figure shows the cable connection of network speed dome to PC. PC Speed Dome Net Switch NVR Figure 3-1 Wiring over LAN Set the IP address of the speed dome for accessing via LAN. Steps: 1.
ST-IP2PTZC QUICK START GUIDE Figure 3-2 Searching Online Devices Note: Devices can be searched and displayed in the list 15 seconds after it goes online; it will be removed from the list 45 seconds after it goes offline. Search online devices manually: You can also click to refresh the online device list manually. The newly searched devices will be added to the list.
ST-IP2PTZC QUICK START GUIDE Figure 3-3 Select a Device Figure 3-4 Modify Network Parameters 3. Enter the IP address of the speed dome in the address field of the web browser to view the live video. Notes: The default IP address is 192.0.0.64. The default user name of administrator is admin, and password is 12345. For accessing the network speed dome from different subnets, please set the gateway for the network speed dome after you log in.
ST-IP2PTZC QUICK START GUIDE 4 Accessing via Web browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 / Server 2003 / Server 2008 32bits CPU: Intel Pentium IV 3.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 7.0 and above version, Apple Safari 5.02 and above version, Mozilla Firefox 3.5 and above version and Google Chrome8 and above version Steps: 1. Open the web browser. 2.
ST-IP2PTZC QUICK START GUIDE Figure 4-2 Download Plug-in Figure 4-3 Install Plug-in 6. Reopen the web browser after the installation of the plug-in and repeat the above steps 2-4 to login. Note: For detailed instructions of further configuration, please refer to the user manual of network speed dome. For further assistance and troubleshooting, please contact SecurityTronix tech support at: (800) 688-9282, press 3 for Tech Support, then press 2 for CCTV.
SECURITYTRONIX 1-Year Limited PTZ Camera Warranty Securitytronix. (the "Company") warrants to the Original Purchaser that the PTZ Camera is free from defects in workmanship or material under normal use. This warranty starts on the date of shipment of the hardware to the Original Purchaser. During the warranty period, the Company agrees to repair or replace, at its sole option, without charge to Original Purchaser, any defective component in the PTZ Camera.
