Shenzhen Suyu Technology Co.,Ltd 产品规格书 Product Specifications Model: 853535P-1050mAh Approved Checked Drawer Shenzhen Suyu Technology Co.
1 Model: 2.1 Li-polymer battery 2.2 Model：853535P-1050mAh 2 Details: Items Remarks 2.1 Standard capacity 1050mAh Discharge current ：0.5 C5A Capacity Minimum capacity 1000mAh Ending discharge voltage ：3.0V Discharge current ：0.5 C5A 2.2 Standard Voltage 3.7V 2.3 Internal resistance ≤80mΩ 2.4 Ending discharge voltage 3.00V 2.5 525mA Charging Current Ending discharge voltage ：3.0V Standard Charging current 0.5 C5A 2.6 The max charging voltage 4.250V 2.7 Discharging time About 2.
11 853535P-1050mAh Size picture b d Ni Tab L c a Al Tab b W T 4.1 the dimensions Thickness: 8.7 mm or less (when the measurement instrument of pressure acting on the battery is 300 gf, temperature of 25 + 2 ℃) Width: 35.0 + / - 0.5 mm Length: 36.0 + / - 1.5 mm Note: the battery storage or use inflation happens at high temperature. 4.
5.2 test equipment requirements 5.2.1 precision measuring instrument for size should be greater than or equal to 0.01 mm. 5.2.2 multimeter to measure the accuracy of voltage and current shall be not less than 0.5 on the Richter scale, measure the voltage when the internal resistance should not be less than 10 k Ω/V. 5.2.3 requires internal resistance tester measuring principle should be 1 KHZ (LCR) ac impedance method. 5.2.4 battery testing system of current accuracy should be + / - 0.
.6.2.2 standard charge, put aside 30 min, 1 to 3.000 V, c5a discharge aside 30 min, repeat the above steps for circulation, until the battery discharge capacity 3 consecutive 80% or less 3 weeks discharge capacity, to test the temperature of 25 + 2 ℃ (important parameters affecting cell cycle performance), requirements are as follows: Cycling times ≥100 5.6.
5.8 safety performance project The test method Thermal shock request Charging standard, and let sit 24 h, and then put the battery in hot box, hot box temperature for the solution of (5 + 2 ℃) rose to 130 No fire, no explosion + 2 ℃ / min rate and thermal insulation for 30 min After charging standards, puts the battery with the thermocouple in the fume hood, batteries and slide rheostat in series on a constant current constant voltage source, the voltage of 4.
battery usage guidelines Carefully read the following precautions to ensure the correct use of lithium ion batteries S h e n z h e n S u y u Te c h n o lo g y C o . , L t d in violation of the following considerations shall not be responsible for any problem. Dangerous! Don't read carefully the following matters may cause battery leakage, explosion, or fire.
When children use battery, need according to the content of the user manual to teach them, and pay close attention to them to ensure the correct use of the battery. If the battery leakage, electrolyte to skin or clothes, immediately wash affected area with flowing water, otherwise may cause skin irritation. Read battery device specifications, correct installation and removal of the battery.
Units mm 2110DB-8205A PCB Wire 1571-26# L 100±3 L1 0.5~2.0 T ≤8.7 W 35.0±0.5 H 36.0±1.5 Drawer Checked Date Approved 12 protection plate parameters 12.1 components Listing NO.
12.3 technical parameters The test items The input voltage(between Min 0.3 Typ Max 9 Unit V 4.25 4.05 - 4.30 4.10 80 4.35 4.15 200 V V s 2.3 2.9 2.0 1.0 20 -40 2.4 3.0 40 3.5 10 3.0 45 2.5 3.1 100 6.0 20 6.
