SecurityMan ® an SecurityM CH1 CH2 CH3 SET AVWatch Day/Night Motion/Audio sensor 2.
Copyright Notice This manual is furnished under license and may be used or copied only in accordance with the terms of such license. Except as permitted by such license, no part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or any means, electronic, mechanical, recording, or otherwise, including translation to another language or format, without the prior written permission of SecurityMan.
Warranty SecurityMan warrants that this product will be free from defects in materials and workmanship for period of time specified on the product packaging. This limited warranty shall commence from the date of purchase. SecurityMan Products warranty is not transferable and is limited to the original purchaser. If the product is found to be defective then, as your sole remedy and as the manufacturer's only obligation, SecurityMan will repair or replace the product .
Notice: 2.4Ghz wireless camera works at ISM band. It may cause interferences with other wireless equipment that operates at the same band. Please turn off one of the equipment to eliminate the interference. Product Assurance 2.4Ghz wireless camera will emit electromagnetic wave, just like other wireless products. But the output power of the products is lesser than other wireless products such as mobile phones. The 2.
Conditions Please read the following messages to make sure whether your working environment is suitable. • Ensure there is enough space around the receiver for ventilation. • The temperature should be kept between –20˚C and 50˚C (-4F – 122˚F). The relative humidity should remain from 20% to 80%.
Contents Introduction Package Contents Technical Support SM-850 Camera Features SM-733 Receiver Features Product Basics Installation Diagram Adapter & Battery Adapter Battery Installation Camera Channel Setup Hanging Bracket Alarm Setup Alarm Setting Switch Alarm Indicator Snooze button on Receiver Mode Control Setup Channel Set Channel-Scan Set Alarm Set Night Vision Troubleshooting 7 7 7 8 8 9 10 10 10 11 11 15 15 16 16 16 16 17 18 18 18 18 20 6
Introduction Thank you for purchasing AVWatch Day/Night Motion/Audio Sensor Wireless Color Camera Kit. It consists of a vivid CMOS Color Camera with night vision (B/W), and a Video Receiver unit which you connect to a TV anywhere in your home (up to 100ft. away from the camera). The Camera converts the video and audio signals into radio signals and transmits them to the Video Receiver.
SM-850 Camera Features: • • • • • Vivid CMOS color camera with night vision (B/W) Selectable motion or audio detection triggers recorder alarm 3 channels available to avoid possible interference Special bracket for desktop and wall-mount Up to 300ft. video transmission (up to 100ft for indoor and up to 300ft for clear line of sight.
Product Basics Camera Antenna Alarm Setting Switch PIR Motion Sensor Alarm Indicator Audio Sensor OFF Camera Lens IR light PIR Motion Sensor Power Indicator DC8V Desktop Base ON/OFF DC Power Jack Power ON/OFF Receiver Alarm Speaker Mute DC8V OFF SET CH1 CH2 CH3 Channel Display Channel Switch ALARM ON ALARM OFF ON 1 2 3 L A/V OUT DC Power AV Mode Jack Output Control Antenna 9
Installation Diagram VCR/DVR Audio / Video OR SET CH1 DC Power CH2 CH3 DC Power TV/ Monitor WARNING: When using power adapter, make sure the voltage indications on the adapters are compatible to the devices to avoid potential damages for incorrect usage of power. Adapter & Battery Adapter 2.4GHz wireless heat detection monitor kit always conform to the authenticated AC adapter.
Battery The camera could be powered by 4 AAA batteries (included) for temporary use. AAA AAA AAA AAA Camera Bottom View Installation 1) Connect the power jack of adapter (DC 8V 300mA) or insert 4 AAA batteries to camera. Turn on the power switch, and the red power indicator light will on.
2) Set the camera to desired Channel, and place the camera at desired location. PIR Motion Sensor Audio Sensor OFF PIR Motion Sensor Audio Sensor OFF 1 2 3 Push Push CH1: 2,414MHz CH2: 2,432MHz CH3: 2,468MHz DC8V ON/OFF DC8V ON/OFF 3) Connect the antenna to the Receiver.
4) Connect one end of the A/V cable to the A/V out jacks of the Receiver. Connect the other end to your TV/Monitor/VCR/DVR A/V jacks. VCR/DVR OR TV/ Monitor SET CH1 5) CH2 CH3 Plug the Receiver’s Power Supply (8V DC 300mA Adapter) into any wall outlet and plug its jack into the Receiver. The channel indicator light will turn on.
6) Turn on the monitor/TV to AV mode. TV/ Monitor AV 7) Press the channel button on the receiver until the Channel LED indication match to the channel on the corresponding camera.. SET CH1 8) CH2 CH3 Adjust the brightness, contrast, and color settings of the Monitor/TV to get the best display effect.
Camera Channel Setup The camera has 3 selectable channel to avoid possible interference from other nearby wireless devices. PIR Motion Sensor Audio Sensor OFF PIR Motion Sensor Audio Sensor OFF 1 2 3 Push Push CH1: 2,414MHz CH2: 2,432MHz CH3: 2,468MHz DC8V ON/OFF DC8V ON/OFF Hanging Bracket The camera can be mounted on the wall by using the hanging bracket in the package. However, the hanging bracket does not include power switch, therefore, power switch function for the camera will be disabled.
Alarm Setup The camera provides either Heat-detection or Voice-detection alarm. You can change alarm method via the alarm setting switch.
Mode Control Setup The receiver can support up to 3 cameras working at the same time. You can adjust the mode control to set the working status as described below. The mode control has the highest priority.
Channel Set: You can confirm which channel is set to receive signal from corresponding camera. (Note: This channel set mode is recommended for channel setting on the receiver than channel switch.) Channel-Scan Set: The Channel-Scan function support multi-camera usage. When the camera turn on, all available channels will display one by one looping in turn per 5 second. So that you can watch the situation from up to 3 different cameras via one receiver.
Troubleshooting Abnormal Phenomena Possible Reasons/Solutions *Check the camera / receiver connected to power supplies, and power on. *Check if the channel of receiver is corresponding to camera; *Check the distance and blocks. *Interfered by other sources; *Check the distance and blocks. *Mismatching system of PAL TV and NTSC cameras or vice versa. EU Environmental Protection Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
www.securitymaninc.
