SecurityMan ® an SecurityM Snooze CH1 CH2 CH3 Channel AVLCD Day/Night Motion/Audio sensor 2.
Copyright Notice This manual is furnished under license and may be used or copied only in accordance with the terms of such license. Except as permitted by such license, no part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or any means, electronic, mechanical, recording, or otherwise, including translation to another language or format, without the prior written permission of SecurityMan.
Warranty SecurityMan warrants that this product will be free from defects in materials and workmanship for period of time specified on the product packaging. This limited warranty shall commence from the date of purchase. SecurityMan Products warranty is not transferable and is limited to the original purchaser. If the product is found to be defective then, as your sole remedy and as the manufacturer's only obligation, SecurityMan will repair or replace the product .
Notice: 2.4Ghz wireless camera works at ISM band. It may cause interferences with other wireless equipment that operates at the same band. Please turn off one of the equipment to eliminate the interference. Product Assurance 2.4Ghz wireless camera will emit electromagnetic wave, just like other wireless products. But the output power of the products is lesser than other wireless products such as mobile phones. The 2.
Conditions Please read the following messages to make sure whether your working environment is suitable. • Ensure there is enough space around the receiver for ventilation. • The temperature should be kept between –20˚C and 50˚C (-4F – 122˚F). The relative humidity should remain from 20% to 80%.
Contents Introduction Package Contents Technical Support SM-850 Camera Features SM-713 Receiver Features Product Basics Installation Diagram Adapter & Battery Adapter Battery Add-on Battery Pak (optional) Installation Camera Channel Setup Hanging Bracket Alarm Setup Alarm Setting Switch Alarm Indicator Snooze button on Receiver Mode Control Setup Channel Set Channel-Scan Set Alarm Set Night Vision Troubleshooting 7 7 7 8 8 9 10 10 10 11 11 12 15 15 16 16 16 16 17 18 18 18 18 19 6
Introduction Thank you for purchasing AVLCD Day/Night Motion/Audio Sensor Wireless LCD Monitoring Kit. It consists of a vivid CMOS Color Camera with night vision (B/W), and a handheld portable design LCD display Monitor. The Camera converts the video and audio signals into radio signals and transmits them to the LCD display Monitor. Note: Please read the manual entirely before using the product. Package contents: Wireless Color Camera (SM-850) x 1 2.
SM-850 Camera Features: • • • • • Vivid CMOS color camera with night vision (B/W) Selectable motion or audio detection triggers recorder alarm 3 channels available to avoid possible interference Special bracket for desktop and wall-mount Up to 300ft. video transmission (up to 100ft for indoor and up to 300ft for clear line of sight.) • Built-in microphone for audio detection • No pet motion false alarm SM-713 Receiver Features: • • • • • • • Handheld portable design 2.
Product Basics Camera Antenna Alarm Setting Switch PIR Motion Sensor Alarm Indicator Audio Sensor OFF Camera Lens IR light PIR Motion Sensor Power Indicator DC8V Desktop Base ON/OFF Power ON/OFF DC Power Jack Earphone Jack LCD Monitor/Receiver Indicator Antenna Channel Button Speaker Volume Control Brightness Control Barcket CH1 SNOOZE CH2 CH3 CHANNEL Video Output ALARM ON ALARM OFF ON 1 2 3 L DC9V OFF VIDEO OUT Speaker DC Power Mode Control Jack ON/OFF Alarm Snooze Button BRIG
Installation Diagram DC Power OR DC Power Add-on Battery Box (Optional) WARNING: When using power adapter, make sure the voltage indications on the adapters are compatible to the devices to avoid potential damages for incorrect usage of power. Adapter & Battery Adapter 2.4GHz wireless heat detection monitor kit always conform to the authenticated AC adapter.
Battery The camera and receiver could be powered by 4 AAA batteries (included) for temporary use. (Batteries life: SM-850 camera, approximately 1.5hr ; SM-713 monitor/receiver, approximately 1hr) AAA AAA AAA AAA AAA AAA AAA AAA OFF ALARM ON ON ALARM OFF 1 2 3 L Camera Bottom View LCD Monitor/Receiver Back View Optional Add-on Battery Pak (optional) ON/OFF ON/OFF BRIGHE BRIGHE MIN MIN MAX Add-on Battery Pak MAX The receiver can be powered by rechargeable add-on battery pak.
Installation 1) Connect the power jack of adapter (DC 8V 300mA) or insert 4 AAA batteries to camera. Turn on the power switch, and the red power indicator light will on. Power Outlet AAA AAA AAA AAA Camera Bottom View Connect the power jack of adapter (DC 9V 400mA), insert 4 AAA batteries or attach the add-on battery pak to receiver. Turn on the power switch, and the red power indicator light will on.
3) Set the camera to desired Channel, and place the camera at desired location. PIR Motion Sensor Audio Sensor OFF PIR Motion Sensor Audio Sensor 1 OFF 2 3 Push Push CH1: 2,414MHz CH2: 2,432MHz CH3: 2,468MHz DC8V ON/OFF DC8V ON/OFF 4) Press the Channel button on the receiver until the Channel LED indication match to the channel on the corresponding camera, and the LED monitor will display pictures.
Adjust the brightness and volume control to get satisfied effect. Volume Control Brightness Control ON/OFF BRIGHE MIN MAX 5) Receiver can also be powered by an add-on battery pak (optional) for portable usage. The add-on battery pak can be recharged individually by connecting the adapter (DC 9V 1500mA) directly to the battery pak itself, with or without removing the battery pak from receiver.
Camera Channel Setup The camera has 3 selectable channel to avoid possible interference from other nearby wireless devices. PIR Motion Sensor Audio Sensor OFF PIR Motion Sensor Audio Sensor 1 OFF 2 3 Push Push CH1: 2,414MHz CH2: 2,432MHz CH3: 2,468MHz DC8V ON/OFF DC8V ON/OFF Hanging Bracket The camera can be mounted on the wall by using the hanging bracket in the package. However, the hanging bracket does not include power switch, therefore, power switch function for the camera will be disabled.
Alarm Setup The camera provides either Heat-detection or Voice-detection alarm. You can change alarm method via the alarm setting switch.
Mode Control Setup The receiver can support up to 3 cameras working at the same time. You can adjust the mode control to set the working status as described below. The mode control has the highest priority.
Channel Set: You can confirm which channel is set to receive signal from corresponding camera. (Note: This channel set mode is recommended for channel setting on the receiver than channel switch.) Channel-Scan Set: The Channel-Scan function support multi-camera usage. When the camera turn on, all available channels will display one by one looping in turn per 5 second. So that you can watch the situation from up to 3 different cameras via one receiver.
Troubleshooting Abnormal Phenomena Possible Reasons/Solutions *Check the camera / receiver connected to power supplies, and power on. *Check if the channel of receiver is corresponding to camera; *Check the distance and blocks. *Interfered by other sources; *Check the distance and blocks. *Mismatching system of PAL TV and NTSC cameras or vice versa. EU Environmental Protection Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
www.securitymaninc.
