User Manual 9313 1881
Agility 3 User Manual Important Notice This guide is delivered subject to the following conditions and restrictions: This guide contains proprietary information belonging to RISCO Group. Such information is supplied solely for the purpose of assisting explicitly and properly authorized users of the system.
Agility 3 User Manual Table of Contents User Manual ................................................................................................................................................. 1 Chapter 1 - Introduction ....................................................................................... 5 1.1 Key Features ........................................................................................................................................... 5 1.2 Agility Architecture ............
Agility 3 User Manual Chapter 4 - User Functions and Settings ........................................................... 26 4.1 User Codes............................................................................................................................................ 26 4.2 Proximity Tags ..................................................................................................................................... 28 4.3 Defining Follow Me Destinations .....................................
Agility 3 User Manual Chapter 1 - Introduction Congratulations on your purchase of Agility 3- RISCO Group's Picture Perfect Wireless Security System. RISCO Group’s Agility 3 elegantly combines state-of-the-art video verification and Smartphone apps with advanced wireless security and safety features.
Agility 3 User Manual 1.2 Agility Architecture Your Agility controls and monitors a variety of sensors, detectors, and contacts placed throughout the premises, which provide external, perimeter and internal burglary protection. The system is supervised, meaning that the panel checks the status of each sensor to detect problems. If the panel detects trouble it will notify you with beeps and indicator lights on the panel itself.
Agility 3 User Manual 1.3 User Operating Tools The Agility system can be operated using several devices, some of which have been designed as bi-directional. If you have purchased a bi-directional device your system is capable of sending a return reply status indication from the panel to the device for each command that is sent to it.
Agility 3 User Manual SMS: If your system is equipped with a GSM/GPRS module it can provide information about the system such as event occurrences by SMS. You can also operate the system using SMS commands for arming and disarming the system and more. Configuration Software: RISCO Group's Configuration Software enables the installer to program the system and operate the system locally or remotely.
Agility 3 User Manual 1.4 Status Indications LED Indicators The LED indicators provide typical system indications, as discussed below. Some indicators have additional functions, which are explained later on. Power LED (Green) The Power LED indicates system operation.
Agility 3 User Manual Status Button / Service Call (Listen & Talk) The button on the main unit can be defined as a system status indicator or as a S.O.S button. Once pressed, a service call can be established to the monitoring station, which then enables 2-way communication with the premises.
Agility 3 User Manual Sound Indications In addition to the visual indications provided by the Agility’s LEDs, your system produces audible notification after certain events. Condition Description Intrusion alarm Continues rapid beeping Fire alarm Staggered rapid beeping Exit delay Slow buzzer beeps until the Exit Delay time period expires Entry delay Slow buzzer beeps until the Entry Delay time period expires.
Agility 3 User Manual Chapter 2 - Local System Operation 2.1 Arming your system Arming your system causes the intrusion detectors to trigger an alarm when violated. The arming operation will be followed by a local message announcement (if defined). Before arming the system check the Ready LED and make sure that the system is ready to be armed. If the system is NOT ready to be armed secure or bypass the violated zone(s), and then proceed.
Agility 3 User Manual Click Full Arm Stay (Home) arming: Stay arming activates only perimeter detectors (as defined by your installer), enabling individuals to remain inside and move about the premises while the system is partially armed. To arm using Stay (Home) arming procedure Quick mode: High security mode: + code Quick mode: High security mode: + code or proximity tag Press button or button 4 (if defined.
Agility 3 User Manual To arm using Partition arming (Away or Stay) procedure Quick mode: / High security mode: Quick mode: / High security mode: / / / > / + code / > / / > / / > / + code or proximity tag Press button or button 4 (if defined. Advise with your installer) Send SMS: [Code][A or H] [Partition 1,2 or 3]. Example 1234A1. For more information refer to page 23. Force Arming: Force arming arms the system regardless of open zones. Your installer must enable this option.
Agility 3 User Manual 2.2 Disarming your system Disarming your system causes the detectors not to trigger an alarm when violated. When you enter the premises, the Entry Delay begins to count down. You must disarm the system within the Entry Delay time to prevent the system from triggering an alarm. The disarming operation will be followed by a local message announcement (if defined). Note: If an alarm occurred in the system, it is recommended to leave the premises.
Agility 3 User Manual Enter your user code and click DISARM Partition disarming: Partition disarming enables you to disarm individual partitions within an armed system To disarm using Procedure for Partition Disarming Quick mode: / / High security mode: / / > > / / > > Code > code or proximity tag. Press the button. All partitions assigned to the button will be disarmed. Send SMS: [Code][D] [Partition 1,2 or 3]. Example 1234D1. For more information refer to page 23.
Agility 3 User Manual Disarming after an alarm: When silencing an alarm the system goes into a disarm state. After the system is disarmed the sirens will sound 4 siren chirps indicated that an alarm occurred in the system. On the keypad, press last alarm. for 2 seconds in order to view information about the If an "Entry door" is opened prior to disarming the system, the following voice announcement message will be heard: "Alarm occurred in the system". Press the key will indicate the cause of the alarm.
Agility 3 User Manual Installer Reset Your monitoring station (MS) or installer can reset your system remotely or locally from the keypad. To enable local reset by your installer you may need to authorize him using the master code after the installer enters his code.
Agility 3 User Manual 2.3 Sending a Panic Alarm Panic alarms enable you to send a message to the monitoring station in the event of an emergency, send a message to a follow me number, announce a local message or activate a local alarm. Panic alarms can be set to be silent (Refer to your installer for more information). To send a Panic Alarm using Procedure Press both Press both and and keys simultaneously keys simultaneously Note: Your installer should define these keys to be set as panic keys.
Agility 3 User Manual Chapter 3 - Remote System Operation 3.1 Remote Phone Operation The Agility enables you to operate the system from a remote touch-tone phone by initiating a telephone call to or from the system and interacting with voice menus that guide you through your required remote operation. Remotely Accessing the System Remotely accessing the system involves initiating a call to the system, and entering your remote access code and the user code you usually enter in the system keypad.
Agility 3 User Manual Operation Quick Key Combination Changing Zone Bypass status Press [3] followed by the zone number and then [#][9] Operating Utility Outputs Press [4] followed by the output number Changing Follow Me(FM) numbers Press [5] followed by the FM number and [#][2]. Enter the new phone number and press [#][1].
Agility 3 User Manual Notes: If no voice is detected, the event message will start playing 5 seconds after phone pick up. Press [#] to begin playback of the event message from the beginning. To repeat the Event Announcement message press [#]. To bypass the Event Announcement message and go directly to the Acknowledge menu, press [*]. 3. Acknowledge the event.
Agility 3 User Manual To listen in or talk: 1. From the Operations/Acknowledge menu, press [6]. The following messages are announced: “To Listen In press 1, To Talk press [2], To Listen and Talk (Open channel) press [3], To return to the previous menu, Press [].” 2. Select the desired option. 3. Press [] to end listening in and talking communication and return to the Operations menu.
Agility 3 User Manual Operation partition SMS Message Structure Example Disarm by Partition [Code] D [Partition No.] 1234D1 Bypass a zone [Code] B [zone number] 1234B05 Un-bypass a zone [Code] UB [zone No.] 1234UB05 Activate Output [Code] UOON [UO No.] 1234UOON1 Deactivate Output [Code] UOOFF [UO No.] 1234UOOFF1 Change FM number [Code] FMPHONE [FM serial number] NEW [New Phone No.
Agility 3 User Manual Self registration To enable the use of the iRISCO App, register your panel to the RISCO cloud. Note: If using GPRS verify with your installer that your panel is set to GPRS communication 1. Navigate your browser to www.riscocloud.com/register 2. Enter your details in the form. 3. In the Panel ID field copy the 15 digits of the panel from the sticker located on the side of the panel Once defined you will be able to use your app or the web from www.riscocloud.com .
Agility 3 User Manual Chapter 4 - User Functions and Settings The functions and settings explained in this chapter can only be performed via your LCD keypad and the Configuration Software. This chapter refers to these functions and settings as performed via the LCD keypad. Refer to the Configuration Software manual for more information regarding how these functions and settings are performed via the Configuration Software.
Agility 3 User Manual Setting / Changing User Codes The user assigned the Grand Master authority level can change all user codes but cannot view the digits in the user code fields. Users with other authority levels can only change their own codes. The system must be disarmed in order to set or change user codes. Note: User codes can also be defined from the web application To set/change a user code: 1. Press 2. Enter your code 3.
Agility 3 User Manual 4. The display will show: "Delete Code. Are you sure?". Use the key to select [Y] and press . If successful, a single confirmation beep is sounded, if not, 3 quick error beeps are sounded 5. Repeat the above steps for deleting additional codes 4.2 Proximity Tags The bi-directional keypad enables you to replace the use of a code with a proximity tag to arm and disarm the security system or to activate and deactivate home appliances and utilities, such as heating and lights.
Agility 3 User Manual Deleting a proximity tag Deleting proximity tags can be done by in two options: By user number: Use this option to delete a tag for which the user is known By tag: Use this option to delete a tag for which the user is not known To delete by user: 1. Follow steps 1-4 of the previous procedure (See Setting/Changing User Codes) 2. Scroll the menu to the option Delete by user. Press 3.
Agility 3 User Manual 6. Enter the phone number, including the area code (if required) or an e-mail address, as requested on the screen and press Up to 32 digits can be included in the phone number. 7. If required, include the special functions described below to achieve the related effect. You can press the or keys to toggle to the required character.
Agility 3 User Manual 5. Select the Scheduling program index number. Use the deactivate and press key to activate / . 4.5 Macro keys Programming Macro Keys Agility enables the installer or Grand Master to record a series of commands and assign them to a macro. When the macro is invoked, the recorded commands are executed from beginning to end. Up to 3 macros can be programmed to a system using the Agility LCD keypad or the Configuration Software.
Agility 3 User Manual Key Represents and 0 simultaneously Deletes your entry from the cursor position forward / Use to toggle between numeric characters / ///#/ and all of the Used to end the sequence and save it to memory 3. Press to save your entry. The series of characters is saved and assigned to the selected macro.
Agility 3 User Manual Operation Grand Master User Installer Main Buzzer On/Off: Used to control the main unit buzzer. √ √ √ Walk test: Used to easily test and evaluate the operation of selected zones in your system √ - √ Output Control: Allows user control of previously designated external devices (e.g. an appliance, a motor-driven garage door, etc.
Agility 3 User Manual Operation Grand Master User Installer Advanced Service Mode:: Used to silence an alarm initiated by any tamper for a Service Time period specified your installer. Use this option when replacing the accessory battery. √ - √ Advanced View IP Address: Use this option to view the IP address of the Agility. √ - - Advanced CS Connect: Enables to establish communication with the configuration software at a predefined location through IP or GPRS.
Agility 3 User Manual Operation Grand Master User Installer Allows the display of any previously entered service information. (Name and phone) √ √ - √ - √ Macro Enables the installer or GM to record a series of commands and assign them to a macro. For more information refer to section 4.5 Macro keys page 31.
Agility 3 User Manual Chapter 5 - System Specifications The following technical specifications are applicable for the Agility: Electrical Characteristics System Power 230VAC (-15%+10%), 50Hz, 50mA Optional: 9VAC, 50-60Hz Units Consumptions Main board: Typical 130mA GSM: Stand by 35mA, Communication 300mA Modem: Stand by 20mA, Communication 60mA IP Card: 90mA (Max) Backup Battery Sealed Lead Acid Battery 6V 3.
Agility 3 User Manual Chapter 6 - EN 50131 Compliance Compliance Statement Hereby, RISCO Group declares that the Agility series of central units and accessories are designed to comply with: EN50131-1, EN50131-3 Grade 2 EN50130-5 Environmental class II EN50131-6 Type A UK: PD 6662:2004, ACPO DD243:2004 (Police) Possible logical keys calculations: Logical codes are codes typed in the wireless keypad to allow level 2 (users) and level 3 (installer) access All code lengths are 4 digits long 0-9 can be used for
Agility 3 User Manual Appendix A - Keypad User Operations The following section details the user operations from the 2-way LCD wireless keypad. User operation can be defined to be activated by a quick mode or high security mode that requires the use of a code or proximity tag. In the high security mode the proximity tag can be used as a substitute for inserting a user code when the display prompts to "Insert a code".
Agility 3 User Manual Operation 1 Fire Alarm Quick Operation High Security Mode Press and hold simultaneously for 2 seconds Emergency/Medical Alarm Press and hold simultaneously for 2 seconds System Chime On/Off Press and hold the button Main Unit Speaker Volume Set keypad LCD contrast for 2 seconds Press and hold the button for 2 seconds Select the volume level (0=No sound, 4=Full volume) Press and hold to save your selection Press and hold for 2 seconds Use the keys to adjust the keypa
Agility 3 User Manual Operation Quick Operation Changing Keypad Language Press and hold simultaneously for 2 seconds. Select the language and press to confirm.
Agility 3 User Manual Appendix B - Remote Control User Operations The following section details the user operations from the Agility 2-Way Remote Control. User operation can be defined to be activated by a quick mode or high security mode that requires the use of a code.
Agility 3 User Manual Code Status LED/Buzzer Indications After each transmission (indicated by a flashing Green LED) from the remote control, the Agility sends a status response indicated by the remote control's LEDs and Buzzer: LED Indications Operation 1st LED * (Send command) 2nd LED (Receive Status) Away Arm Green Red Stay Arm Green Orange Disarm Green Green Alarm Green Flash Red LED *If the 1st LED changes to orange it indicates a low battery condition.
Agility 3 User Manual Appendix C - Installer Event Log Messages Event Message Activate UO=xx Description UO XX activation Actv UO=xx KF=zz AL Reinstate P=y UO XX is activated from remote control ZZ Alarm reinstatement on partition Y Alarm abort P=y Alarm aborted on partition Y * Alarm Zone=xx Alarm in zone no.
Agility 3 User Manual Event Message Comm OK Siren=y Description Communication OK between the Agility and Siren Y Comm. OK GSM Comm.OK I/O Mdl. Communication OK between the Agility and GSM Communication OK between the Agility and I/O module * Conf. alarm P=y Confirmed alarm occurred in partition Y Conf.
Agility 3 User Manual Event Message * GSM: Module comm. Description Internal GSM/GPRS BUS module trouble * GSM:NET avail. GSM:NET avail.OK GSM network is not available GSM Network is available GSM:NET qual.
Agility 3 User Manual Event Message * Ksw away:P=y Description Partition Y is armed by key switch * Ksw disarm:P=y L.bat rstr KF=yy Partition Y is disarmed by key switch Low battery trouble restore from wireless remote control YY L.Temp rst Zn=xx Low temperature alert restored from zone XX defined as a temperature detector * Lost Zone=xx Low Bat rs Z=xx Wireless zone lost, zone no. XX Low battery trouble restored from wireless zone no. XX Low bat. Zn=xx Low bat.
Agility 3 User Manual Event Message Soak fail Z=xx Description Zone XX has failed in the soak test Special KP=y Spkr l.bat rsS=y Special alarm from the from wireless keypad Y Speaker low battery restore from siren Y * Spkr low bat S=y Speaker low battery trouble from siren Y Start exit P=y * Stay:P=y C=zz Exit time started in partition Y Partition Y stay armed by user ZZ * Stay: P=y KF=zz * Tamper I/O Mdl. Partition Y stay armed by remote control ZZ Tamper alarm from I/O module Tamper I/O Mdl.
Agility 3 User Manual Appendix D: Web User Application The Web User Application provides a full interface to your system from a PC, cellular phone or PDA using the WAP portal. Via the Web you can perform a wide range of tasks such as arm/disarm, zone bypass, user code management and home automation control. . Logging In This application is hosted by your service provider behind a secure firewall. Access your account through the supplied portal address (default: www.riscocloud.com) login page.
Agility 3 User Manual Menu Bar Home Workspace Status Bar Menu Bar Use the Menu Bar to access the application functionality as per the above diagram. The following options are available from the Main Menu: Home – pressing the Home button allows the user to return to the Main page at any time Arm/Disarm – enables remote system disarming and (full or partial) arming Settings – offers various maintenance and management options including user codes, passwords, alerts, and zone bypass.
Agility 3 User Manual Workspace The workspace offers additional links to the following pages of the application, including: Users and Codes, History, Alerts, Change Password, Video. When you choose a page, either from the Main Menu, or from the workspace, the page is displayed in the workspace. For example, if you choose Arm/Disarm from the Main Menu, System Operation area and System Status area are displayed in the workspace (see the figure below).
Agility 3 User Manual User code management The Users and Codes page enables you to manage your system's users. The page displays a table of the system's current users and enables you add, edit and delete users as required. Please note that this capability is available only to a user with a Master code, the highest level of authorization. Adding a New User To add a new user: 1. Click ADD NEW USER at the bottom of the table; the Add New User page opens. 2.
Agility 3 User Manual 3. Choose the user type from the available options. 4. Enter the new user's 4-digit passcode. 5. Enter the new user's passcode again for confirmation. 6. Enter your Master code. 7. Click Update. Editing Existing Users To edit an existing user: 1. Click Edit for the user you want to modify; the Edit User page opens. 2. Edit the user's name in the field provided (16 characters max.). When editing an existing user, you cannot change the user type. 3.
Agility 3 User Manual Master users can click a listing bottom displayed ADD NEW row to enable creation of a new user, similar to the process of Self registration: Verify Password Change Password Click Settings then Change Password to change the password you use to login to the Web Application.
Agility 3 User Manual Zone Bypass On The Main Page menu, click SETTINGS then Zone Bypass to bypass specified zones in your home that you don't want to receive event messages from. The Zone Bypass page displays a list of the zones (i.e. sensors) in your system and allows you to bypass them or unbypass them as required. A bypassed zone is ignored by the system and will not generate an alarm when triggered.
Agility 3 User Manual Change Appearance On The Main Page menu, click SETTINGS then Change Appearance to change the color scheme of your account.
Agility 3 User Manual Alerts The Alerts feature allows those people included in your contact list to be notified by email when certain events occur. To add alert notification recipients to your contact list 1. On the SETTINGS tab, click the Alerts sub-menu to display the following: 2. Click ADD NEW to add email addresses or cellular telephone numbers for the alert messages or click Edit to modify and existing alert recipient 3. In the Name field, enter the name of the contact to receive alerts. 4.
Agility 3 User Manual Event Log History The History page displays a log of events that have occurred within your system. For each event you can view the date and time that the event occurred, a description of the event and the user or device that caused the event. Additionally, you can see whether or not the event was reported to your monitoring service. When the log is full, the oldest events are automatically purged and are replaced by new events.
Agility 3 User Manual Video Verification Using the 2-way wireless video verification PIR detectors installed in your home, the Web Application enables you to view live images over the Web through the Cameras submenu. Use the Images sub-menu to browse Stored Video Events images. Discuss this capability with your security service provider to determine if it is applicable to your system.
Agility 3 User Manual FCC Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Agility 3 User Manual RISCO Group Limited Warranty RISCO Group and its subsidiaries and affiliates ("Seller") warrants its products to be free from defects in materials and workmanship under normal use for 24 months from the date of production. Because Seller does not install or connect the product and because the product may be used in conjunction with products not manufactured by the Seller, Seller cannot guarantee the performance of the security system which uses this product.
