User`s guide

12
12
Outputs On Off
User Code Level: 5 and above.
Function: Allows you to turn the system relay outputs on and off.
This function is used to individually turn your system’s relay outputs
on and off. Your system may use these outputs to control interior and
exterior lighting, heating, air conditioning, or other appliances.
The names and numbers of the relays connected to your system are
located in the System Setup section of this guide.
Turning the Outputs On and Off
1. Access the User Menu.
2. Press COMMAND until OUTPUTS ON/OFF? displays.
3. Press any SELECT key to display OUTPUT: - ON OFF.
4. Enter the output number you want to turn on or off. The output
number will appear in the display.
5. With the output number displayed, press the SELECT key under
ON or OFF. The output is then turned on or off, depending on your
selection, and remains in that state until you change it.
Under certain conditions, some outputs cannot be turned on. If you
select a restricted output, the keypad displays CANNOT TURN ON.
6. The system automatically removes the output number and a new
output number can be entered. Refer back to step 4.
Press the ARROW key to exit the User Menu.
User Menu
Zone Status
User Code Level: All users at any time.
Function: Displays a list of armed, bypassed, or alarmed zones. Also
allows you to check the status of individual zones.
Zone Status can be used to give you a list of zones by category or
display the current status of an individual zone number. The four
categories are:
• Armed Zones - zones that are currently armed.
• Bypassed Zones - zones that are currently bypassed.
• Alarmed Zones - zones that have gone into alarm during the
current or previous armed period.
• Number - enter the number of any zone to check its status.
Using the Zone Status Function
1. Access the User Menu.
2. Press COMMAND until ZONE STATUS? displays. You can also
just enter the zone number (1 to 299) and press COMMAND. The
zone number and name is displayed followed by its status.
3. Press any SELECT key to display ARM BYPS ALR NBR.
4. Select ARM for a list of zones that are currently armed. You can
scroll through the list by pressing the COMMAND key.
5. Select BYPS for a list of zones that are currently bypassed.
6. Select ALR for a list of zones that have gone into alarm during the
current or previous armed period.
7. Press NBR and ZONE NO: - will be displayed.
Outputs On Off
User Code Level: 5 and above.
Function: Allows you to turn the system relay outputs on and off.
This function is used to individually turn your system’s relay outputs
on and off. Your system may use these outputs to control interior and
exterior lighting, heating, air conditioning, or other appliances.
The names and numbers of the relays connected to your system are
located in the System Setup section of this guide.
Turning the Outputs On and Off
1. Access the User Menu.
2. Press COMMAND until OUTPUTS ON/OFF? displays.
3. Press any SELECT key to display OUTPUT: - ON OFF.
4. Enter the output number you want to turn on or off. The output
number will appear in the display.
5. With the output number displayed, press the SELECT key under
ON or OFF. The output is then turned on or off, depending on your
selection, and remains in that state until you change it.
Under certain conditions, some outputs cannot be turned on. If you
select a restricted output, the keypad displays CANNOT TURN ON.
6. The system automatically removes the output number and a new
output number can be entered. Refer back to step 4.
Press the ARROW key to exit the User Menu.
User Menu
Zone Status
User Code Level: All users at any time.
Function: Displays a list of armed, bypassed, or alarmed zones. Also
allows you to check the status of individual zones.
Zone Status can be used to give you a list of zones by category or
display the current status of an individual zone number. The four
categories are:
• Armed Zones - zones that are currently armed.
• Bypassed Zones - zones that are currently bypassed.
• Alarmed Zones - zones that have gone into alarm during the
current or previous armed period.
• Number - enter the number of any zone to check its status.
Using the Zone Status Function
1. Access the User Menu.
2. Press COMMAND until ZONE STATUS? displays. You can also
just enter the zone number (1 to 299) and press COMMAND. The
zone number and name is displayed followed by its status.
3. Press any SELECT key to display ARM BYPS ALR NBR.
4. Select ARM for a list of zones that are currently armed. You can
scroll through the list by pressing the COMMAND key.
5. Select BYPS for a list of zones that are currently bypassed.
6. Select ALR for a list of zones that have gone into alarm during the
current or previous armed period.
7. Press NBR and ZONE NO: - will be displayed.