User`s guide

6
6
General Arming Operation
Your burglary protection is divided into areas. Each area has a custom
name, can be turned on or off independent of other areas, and can
have different schedules and authorized users.
After making your arming selection, the keypad displays any zones
that are currently bypassed. These zones remain bypassed until the
system is armed and then disarmed. Any 24 hour zones in a bad
condition are also displayed.
Before arming, the system verifies that all doors, windows, and other
protection devices to be armed are in normal condition.
If everything is okay, the system arms. If there is a problem on one or
more burglary zones the system cannot arm until the problem is
corrected. If the problem is simply an open door or window, correct the
problem and try arming again.
If the problem cannot be corrected, you can force arm or bypass the
zone or wait until the zone can be repaired by a service technician. A
force armed zone is ignored by the system until it restores to normal.
A bypassed zone is ignored by the system during the entire armed
period. A zone remains bypassed until the system is disarmed.
In some cases, you might see the keypad display FRONT DOOR
BAD *. The asterisk next to BAD means that the zone is a priority
zone, which cannot be bypassed. The problem on the zone must be
corrected before the system can be armed.
Introduction
Armed Message: After all bypassing is completed or zone faults
corrected, the keypad briefly displays ALL SYSTEM ON if all areas
in the system are arming and SYSTEM ON if only selected areas are
arming. The keypad then displays the exit delay time as it counts
down. When the exit delay time expires, all disarmed zones are
armed.
If your system uses a keyswitch to arm an area, the exit delay time is
NOT shown on the keypad display.
ONE MOMENT . . . Message: If your system is monitored, it may be
programmed to wait for the transmission of an arming report to the
central station before displaying the armed message. See Arming
Report below. This is to verify your phone lines are working properly.
While the system is waiting for the transmission, the display reads
ONE MOMENT.... If the report is received, the keypad displays the
armed message. If the report is not received, the keypad displays
LOCAL ALARM ONLY before displaying the armed message.
Arming Report: Your system can be programmed to send arming or
zone bypassing reports to a central station. This feature is optional
and can be programmed for you at any time.
General Arming Operation
Your burglary protection is divided into areas. Each area has a custom
name, can be turned on or off independent of other areas, and can
have different schedules and authorized users.
After making your arming selection, the keypad displays any zones
that are currently bypassed. These zones remain bypassed until the
system is armed and then disarmed. Any 24 hour zones in a bad
condition are also displayed.
Before arming, the system verifies that all doors, windows, and other
protection devices to be armed are in normal condition.
If everything is okay, the system arms. If there is a problem on one or
more burglary zones the system cannot arm until the problem is
corrected. If the problem is simply an open door or window, correct the
problem and try arming again.
If the problem cannot be corrected, you can force arm or bypass the
zone or wait until the zone can be repaired by a service technician. A
force armed zone is ignored by the system until it restores to normal.
A bypassed zone is ignored by the system during the entire armed
period. A zone remains bypassed until the system is disarmed.
In some cases, you might see the keypad display FRONT DOOR
BAD *. The asterisk next to BAD means that the zone is a priority
zone, which cannot be bypassed. The problem on the zone must be
corrected before the system can be armed.
Introduction
Armed Message: After all bypassing is completed or zone faults
corrected, the keypad briefly displays ALL SYSTEM ON if all areas
in the system are arming and SYSTEM ON if only selected areas are
arming. The keypad then displays the exit delay time as it counts
down. When the exit delay time expires, all disarmed zones are
armed.
If your system uses a keyswitch to arm an area, the exit delay time is
NOT shown on the keypad display.
ONE MOMENT . . . Message: If your system is monitored, it may be
programmed to wait for the transmission of an arming report to the
central station before displaying the armed message. See Arming
Report below. This is to verify your phone lines are working properly.
While the system is waiting for the transmission, the display reads
ONE MOMENT.... If the report is received, the keypad displays the
armed message. If the report is not received, the keypad displays
LOCAL ALARM ONLY before displaying the armed message.
Arming Report: Your system can be programmed to send arming or
zone bypassing reports to a central station. This feature is optional
and can be programmed for you at any time.