Specifications

1070 072 131-102 (96.08) GB
Index11-4
– connectivity with other BOSCH controllers and
extraneous communicating devices 2-1
– DIP switch settings 2-5
– function modules 2-1
– operating software
re-initialisation by pressing Reset button 2-3
– power supply 2-1
– precautions against electrostatic discharge
(ESD) 2-5
– setting block address 2-6
– specifications 2-12
R500 firmware 3-1
R500 operating system 8-19
R500 Reset procedure 8-19
R5CON confirmation module
– functional description 6-1
– I/O parameters 6-2
input parameters 6-2
output parameters 6-3
– interaction with R5REQ module 6-1
– introduction 6-1
R5INIT function module
– I/O parameters
output parameter 4-3
– R500 in server-only operation 4-1
R5REQ function module
– I/O parameters 5-1
input parameters 5-2
output parameters 5-3
HIGH byte, PLC response 5-3
LOW byte, error code 5-3
RBA — Result Bit Array
– and job bit array JBA 5-4
– definition 5-3
RD and WR pointers 8-8
RD pointer, see Ring buffer 8-2
RDT — Response Delay Time 9-4
Receive command 8-16, 8-31
RECEIVE connection sequence 9-13
Receive Mode
– definition 8-2
Receive Mode command 8-5, 8-19, 8-27, 8-31, 8-
33
Receive-data length 8-27, 8-28, 8-31
Receiving station RST, see RST 7-12
Request message 9-11
Request sequence detail 9-11
Requesting data 9-10
Reset Receive Buffer command 8-8, 8-18
Response Delay Time 9-4
Response message 9-9, 9-12
Result bit array RBA, definition 5-3
Ring buffer
– definition 8-2
– RD pointer 8-2
RST — Requesting Station
– address, High part 7-4
– address, Low part 7-4
– command attribute 7-4
– command code parameter 7-4
– command-type parameter
input into requesting station 7-3
output from requesting station 7-3
– definition 7-1
– job direction RST <--> PST 7-3
– job implementation 7-11
– operand types 7-3
– protocol-specific parameters in BÜP19E 7-2
RST/PST error catalogue 7-12
—S—
SC table — System Configuration table 4-2
Select Mode command 8-31
Send connection sequence 9-6
Send sequence details 9-8
Seven-segment display
– H31, for X31 interface 2-11
– H32, for X32 interface 2-11
Sicherheitshinweise 1-4
Siemens CP524/CP525 controllers, acting as PST
9-30
Siemens Simatic controller 9-2
spare parts 1-5
Start characters 8-20
Start command 8-12, 8-15, 8-31
Start parameters, BÜP03E 8-15
Status displays 2-11
STX — Start of Text, control character 9-4
Summary, BÜP03E commands 8-28
Syntax 8-18, 8-19, 8-22, 8-24
—T—
Terminate Job command 8-2, 8-11
Terminate Job sequence 8-13, 8-19
Termination via Receive-data length 8-27
Termination via termination character 8-26
Transfer completion sequence 9-2
Transfer response message 9-2
Transfer Routine 9-4
Transfer times 8-14
Transmit command 8-17
Twisted-pair, shielded cable
– baud rate and permitted lengths 2-10
—U—
UART Receive buffer
– definition 8-2
– flushing/Reset 8-7
– function 8-7
– information for processing 8-7
– RD and WR pointers 8-18
– Receive command and BÜP03E Receive buffer
8-8
– receive faults and fault message 8-7
Unrestricted Receive 8-5, 8-26, 8-30
– definition 8-2
Unrestricted Receive command 8-31
User pointer, see PLC Receive buffer 8-2
—V—
V.24 Interface
– differences in potential, sending vs. receiving
device 2-10
V.24/20 mA Interface 2-12
– available protocols 2-5
– cable length 2-10
– introduction 2-5