Specifications

1070 072 131-102 (96.08) GB
Index 11-3
—G—
General-purpose control characters 8-4
—H—
Hex dump, of data in controller 8-4
Hex format, PG editor 8-4
Hex word 8-4
High / Low priority, of devices during access
procedure 9-5
HIGH byte
– R5REQ output parameter, PLC response 5-3
HIGH byte, PLC response in result word 5-6
—I—
Input into the RST 7-3
Input job 7-3
Input parameter
– R5CON module 8-33
computer interface number CXN 6-2
data type 6-2
job number 6-2
– R5REQ module
byte offset 5-2
data type 5-2
data type attribute 5-2
job bit array JBA 5-2
Input, data into PLC memory via PG 8-4
Input, data into PLC memory via PG editor 8-4
Inputting text with control characters 8-4
Interface cable, specifications 2-10
Interlinking depth 8-19
Interlinking, via BÜP03E START command 8-12
Interpreter 9-4
Intervals, between incoming characters 9-6
—J—
JBA — Job Bit Array
– and result bit array RBA 5-4
– definition 5-2
– in R5REQ list of parameters 5-4
– P3 parameter of, 5-3
Job bits, resetting 5-2
Job parameter list 8-2, 8-11
Job queue 2-3
Job status 8-34
—L—
Labelling field 2-2
Left-justified printer output 8-23
LOW byte
– R5REQ output parameter, error code 5-3
LOW byte, error code in result word 5-5
Low-High word principle 8-24
—M—
measuring or testing procedures 1-5
Message header and data 9-8
—N—
NAK — Negative Acknowledge 9-5
Negative Acknowledge 9-5
Normal conclusion via Receive-data length 8-27
—O—
Output from the RST 7-3
Output job 7-3
Output parameter
– R5CON module
fault message 6-4
job number 6-3
status 6-3
– R5INIT module 4-3
– R5REQ module
fault message 5-3
result bit array RBA 5-3
Output to printer 8-1
—P—
PC600 controller, acting as PST 9-30
PCM — Process Coordination Marker
– definition 7-7
– specifying 7-7
PG editor 8-4
PLC interface
function modules
– introduction 3-1
– R5INIT initialisation FM 4-1
characteristic data 4-1
– R5REQ 5-1
– R5REQ function module
characteristic data 5-1
PLC Interface
– R500 in server-only operation 3-1
PLC Receive buffer 8-9
– definition 8-2
PLC Response 8-34
PLC response table 5-6
Printer formatting 8-1
Printer, sending data to 8-1
Process coordination marker, see PCM 7-7
PROFI software
Loader menu, Configuration option 2-12
Protocol loader 2-12
Protocol-dependent parameters 5-4, 5-7
Protocol-independent parameters 5-4, 5-5
Protocols
– filed in BOSCH.BIB subdirectory 2-12
– Loader menu in PROFI software 2-12
– loading in R500/R500P 2-12
PST 7-5
PST — Peripheral Station
– address, High part 7-5
– address, Low part 7-5
– command-attribute 7-5
– definition 7-1
– job implementation 7-11
—Q—
Quad word 7-3, 7-6
Quad word mask 7-3, 7-6
Qualifiziertes Personal 1-2
—R—
R500 Computer interface module
– CL400 slot assignment
GG2 basic unit 2-4
GG2/K basic unit 2-4
– CL500 slot assignment
GG2 basic unit 2-4
GG2/K basic unit 2-4
– compatibility
R500M-EN 2-1
R500P 2-1