Specifications

1070 072 131-102 (96.08) GB
Index 11-1
11 Index
—%—
% character, in control text 8-23
—0—
0 (zero) in control text 8-23
—1—
14 x 0.14 Bosch cable, see Twisted-pair, shielded
cable 2-10
—2—
20 mA Interface
– active operation
signal direction 2-9
23-bit mantissa 8-25
—3—
3964 / 3964R, Siemens protocols 9-1
—7—
7-segment display 2-3
—A—
Accuracy, in representing floating-point numbers 8-
24
Acknowledgement Delay Time 9-4
Acknowledgement interchange 9-4
Active phase, Receive 8-12
Address, zero-filled 8-4
ADT — Acknowledgement Delay Time 9-4
ASCII format, PG editor 8-4
Automatic transfer completion 9-4
—B—
Baud rate (bps) 2-10
BCC — Block Check Character 9-5
Bestimmungsgemäßer Gebrauch 1-1
Block address
– requesting station RST 7-4
Block Wait Time 9-5
BÜP03E receive buffer
– size selection 8-2
BÜP03E Receive buffer
– and Data Copy command 8-5
– copying contents into PLC Receive buffer 8-22
– Data Copy command 8-22, 8-30
– definition 8-2
– fault messages 8-35
– identical to PLC buffer 8-9
– in Conditional Receive mode 8-5
– RD and WD pointers 8-8
– Receive command 8-8
– Unrestricted Receive via R5REQ 8-5
BÜP03E, Bosch transmission protocol for free
configuration 2-5
BÜP19E transfer protocol
– CL500 controller acting as PST 7-7
– command code atttribute 7-4
– command type / operand type parameters 7-2,
7-3
– command type parameters
word masks 7-3
– coordination markers 7-6
– coordination parameter 7-6
– data volume parameter 7-6
– double word mask 7-3
– implementation of coordinated command 7-6
– introduction 7-1
– link installation, assigning high/low priority 7-2
– PG Protocol Loader 7-1
– protocol-specific DIP switch settings (S2) 7-2
– protocol-specific parameters 7-2
– PST address, High part 7-5
– PST address, Low part 7-5
– PST command attribute 7-5
– quad word mask 7-3
– RST address, High part 7-4
– RST address, Low part 7-4
– RST/PST command code parameter 7-4
– word mask 7-3
BÜP19E, Bosch standard protocol for secure data
transmission 2-5
BÜP64 Protocol
– acknowledgement delay time 9-1
– checkback signals 9-17
– CL300 controller, acting as PST 9-30
– CL500 controller, acting as PST 9-27
– DIP switch, protocol end identifier 9-2
– error class 9-19
– fault message summary 9-20
– FETCH data requesting sequence 9-10
– initialisation conflict 9-14
– interaction with R5CON module 9-1
– interaction with R5INIT module 9-1
– interaction with R5REQ module 9-1
– introduction 9-1
– job parameterisation examples
FETCH job, CL500 <- CL300 9-32
SEND job, CL500 -> CL300 9-31
SEND job, CL500 -> CL500 9-33
– job parameters 9-22
– job status 9-17
– main features 9-1
– on Bosch CL300 controller 9-2
– on Bosch PC600 controller identifier 9-2
– on R500/R500P controllers 9-2
– PC600 controller, acting as PST 9-30
– PLC response 9-18
– protocol-specific DIP switch settings 9-2
– protocol-specific parameters 9-23
command/operand type 9-23
coordination markers 9-27
data volume 9-26
field coordination markers 9-27
PST address
DM number 9-25
DM word number 9-25
RST / PST command type 9-24
RST address
block address of central processing unit 9-
24
DM number 9-24
DM word number 9-25
– Quasi-duplex Mode 9-14
– RECEIVE connection sequence 9-13
– request message 9-11