Specifications

1070 072 131-102 (96.08) GB
Index 10-1
10 Index of Figures
Fig. 2-1 CL400 — Slot assignment, GG2 Basic unit...........................................................................2-4
Fig. 2-2 CL400 — Slot assignment, GG2/K Basic unit........................................................................2-4
Fig. 2-3 CL500 — Slot assignment, GG2 Basic unit...........................................................................2-4
Fig. 2-4 CL500 — Slot assignment, GG2/K Basic unit........................................................................2-4
Fig. 2-5 R500 — DIP Switch settings..................................................................................................2-5
Fig. 2-6 V.24/20 mA Interface — Transmission rate DIP switch settings ...........................................2-7
Fig. 2-7 V.24 Interface — Pin assignment ..........................................................................................2-8
Fig. 2-8 20 mA Interface — Pin assignment, active operation............................................................2-9
Fig. 2-9 20 mA Interface — Pin assignment, passive operation .........................................................2-9
Fig. 2-10 V.24/20 mA Interface — Cable lengths..............................................................................2-10
Fig. 2-11 R500 — Specifications.......................................................................................................2-12
Fig. 4-1 R5INIT — Characteristic data................................................................................................4-1
Fig. 4-2 R5INIT — Input parameters...................................................................................................4-2
Fig. 4-3 R5INIT — Output parameter..................................................................................................4-3
Fig. 4-4 R5INIT — Error codes ...........................................................................................................4-3
Fig. 5-1 R5REQ — Characteristic data...............................................................................................5-1
Fig. 5-2 R5REQ — List of parameters ................................................................................................5-4
Fig. 5-3 R5REQ — Protocol-independent parameters........................................................................5-5
Fig. 5-4 R5REQ — Error codes ..........................................................................................................5-5
Fig. 5-5 R5REQ — PLC response ......................................................................................................5-6
Fig. 6-1 R5CON — Characteristic data...............................................................................................6-1
Fig. 6-2 R5CON — HIGH Byte status .................................................................................................6-3
Fig. 6-3 R5CON — LOW Byte status..................................................................................................6-4
Fig. 7-1 BÜP19E — S2 DIP Switch settings .......................................................................................7-2
Fig. 7-2 BÜP19E — Command type / Operand type...........................................................................7-2
Fig. 7-3 BÜP19E — Operand type parameter ....................................................................................7-3
Fig. 7-4 BÜP19E — RST / PST Command code................................................................................7-4
Fig. 7-5 BÜP19E — RST Command attribute.....................................................................................7-4
Fig. 7-6 BÜP19E — RST Address, High part......................................................................................7-4
Fig. 7-7 BÜP19E — RST Address, Low part ......................................................................................7-4
Fig. 7-8 BÜP19E — PST Command attribute.....................................................................................7-5
Fig. 7-9 BÜP19E — PST Address, High part......................................................................................7-5
Fig. 7-10 BÜP19E — PST Address, Low part.....................................................................................7-5
Fig. 7-11 BÜP19E — Data volume parameter....................................................................................7-6
Fig. 7-12 BÜP19E — Coordination parameter....................................................................................7-6
Fig. 7-13 BÜP19E — PLC Response ...............................................................................................7-11
Fig. 7-14 BÜP19E — Error class ......................................................................................................7-11
Fig. 7-15 BÜP19E — Fault messages, Part 1...................................................................................7-12
Fig. 7-16 BÜP19E — Fault messages, Part 2...................................................................................7-13
Fig. 8-1 Control characters — Protocols.............................................................................................8-4
Fig. 8-2 Control characters — General-purpose.................................................................................8-4
Fig. 8-3 UART Receive buffer.............................................................................................................8-7
Fig. 8-4 BÜP03E — Receive buffer ....................................................................................................8-8
Fig. 8-5 BÜP03E — Data exchange between Receive buffers...........................................................8-9
Fig. 8-6 BÜP03E — Interlinking command .......................................................................................8-12
Fig. 8-7 BÜP03E — Chronological sequence of a single communication ........................................8-13
Fig. 8-8 BÜP03E — Transfer times ..................................................................................................8-14
Fig. 8-9 BÜP03E — Start parameters...............................................................................................8-15
Fig. 8-10 BÜP03E — Transmit command parameters .....................................................................8-17
Fig. 8-11 BÜP03E — Reset Receive Buffer command parameters .................................................8-18
Fig. 8-12 BÜP03E — Data-Copy command parameters ..................................................................8-22
Fig. 8-13 BÜP03E — Summary of Commands, Part 1 .....................................................................8-28
Fig. 8-14 BÜP03E — Summary of Commands, Part 2 .....................................................................8-28
Fig. 8-15 BÜP03E — Summary of Commands, Part 3 .....................................................................8-29
Fig. 8-16 BÜP03E — Job status .......................................................................................................8-34
Fig. 8-17 BÜP03E — PLC Response ...............................................................................................8-34
Fig. 8-18 BÜP03E — Error class ......................................................................................................8-35
Fig. 8-19 BÜP03E — Fault messages ..............................................................................................8-35
Fig. 9-1 BÜP64 — S2 DIP switch settings ..........................................................................................9-2
Fig. 9-2 BÜP64 — Job status............................................................................................................9-17