Specifications

115V AC gearmotor assembly
with 3 output shafts: Shaft #1:
410 RPM, 6mm Dia. X 11/16
long, offset from case 9/16", CCW
rotation as viewed from shaft end
Shaft #2: 195 RPM, 6mm Dia. X 13/16 long, offset from
case 1/8", with flat, CCW rotation
Shaft #3: 180 RPM, 6mm Dia. X11/16 long, offset from
case 1/8", with flat, CW rotation
Cast aluminum motor/gear housing with steel cover on
gear case. Fan on back shaft, 10in leads.
L: 7" O/A W 6-1/2” O/A H: 6-1/4” O/A WT: 6.5
15639-MA 3 Shaft Gearmotor Special
$4.95
STOCK # DESC. 1EA
3 OUTPUT
GEARMOTOR
ASSEMBLY
MFG: FUJI
P/N: FM-43E
COIL : 12V
4600 RPM @ 12VDC, 2800 RPM @
6VDC. 4mm dia. X 10mm steel front shaft.
3 threaded mounting holes in front. 3" leads.
L: 3" (Body) DIA: 1-3/8” WT: .4
15581-MD 12VDC FUJI Motor
$9.95 $8.95
STOCK # DESC. 1EA 10+EA
12VDC MOTOR
MFG: JAPAN SERVO
P/N: KP-56LM2G-001
COIL: 3.3VDC/2.2A
TYPE: 2 Phase Uni-Polar 6 lead
STEP ANGLE:1.8 deg (Motor) .1deg. Output (18/1)
Step motor, gear box assembly with brake. Apply 24VDC
to release brake (removable). Motor side 13/32"dia. X 9/
16" steel shaft with coupling (held by roll pin), 6" leads,
Removable steel mtg. bracket.
3.3V STEP MOTOR
ASSEMBLY
L: 4-1/2"(Body) W: 3-1/2" H: 4-1/4" WT: 2.6
16237-MS Step Motor Assembly
$16.95 $15.95
STOCK # DESC. 1EA 10+EA
HANG ZHOU P/N DJ625, non-
resettable, 6 Digit, impulse
counter. Rated 24VDC/.6W/10CPS. Plastic case snap-
in mounts into a 1" X 17/32" cutout. 12in. leads. All have
a couple of test counts on them
24VDC IMPULSE
COUNTER
16521-MI 24VDC Counter $1.95 $1.50
STOCK # DESC. 1EA 25+EA
W: 1-1/16" H: 7/8" D: 1-3/8" WT: .04
MFG: Bimba PORTS: 1/8" NPT
BORE: 3/4" STROKE: 3/4"
USED. Double action, Stainless steel tube, aluminum
heads air cylinder. 200 PSI max pressure. 1/4" Dia. steel
rod X 1/2" (retracted) with 1/4-28 thread. Front mount
5/8"-18 threaded. Sorry, No Mtg. Nuts
L: 4-1/2"Body DIA: 13/16" WT: .2
STOCK # DESC. 1EA 5+EA
8851-HD Pneumatic Cylinder $4.95 $3.95
DOUBLE ACTION
SHORT ROD
CYLINDER
MFG: Bimba PORTS: 1/8" NPT
BORE: 1-1/2" STROKE: 3/4"
USED. Single action, Spring loaded Retract, pressure
extend. Stainless steel tube, aluminum heads, air cylin-
der. 200 PSI max pressure. 7/16" Dia.steel rod X 1"
(retracted) with 7/16-20 thread. Front mount 3/4"-16
threaded. 12 lbs to compress spring. Sorry, No Mtg.
Nuts
L: 4-3/4"Body DIA: 1-5/8" WT: .8
STOCK # DESC. 1EA 5+EA
8850-HD Pneumatic Cylinder $4.95 $3.95
SINGLE ACTION SPRING
LOADED
CYLINDER
MFG: Bimba PORTS: 1/8" NPT
BORE: 1-1/2" STROKE: 7/8"
USED. Single action, Spring loaded extension, pressure
retract. Stainless steel tube, aluminum heads, air cylin-
der. 200 PSI max pressure. 7/16" Dia.steel rod X 1-3/4"
(extended) with 7/16-20 thread. Front mount 3/4"-16
threaded. 12 lbs to compress spring. Sorry,No Mtg. Nuts
L: 4-3/4"Body DIA: 1-5/8" WT: .8
STOCK # DESC. 1EA 5+EA
8849-HD Pneumatic Cylinder $4.95 $3.95
SINGLE ACTION SPRING
LOADED
CYLINDER
SUSPA P/N C16-
09786 gas extension
spring. Used to lift & support
equipment hoods & doors, car hoods
& trunk lids.
Ball pivot on both ends, threaded 1/4-20
Center -to-center Extended length: 19.7in.
Center -to-center Compressed length: 11.8in
Extension Force: 30lbs.
WT: .8
16694-HD Suspa Gas Spring
$3.95 $3.50
STOCK # DESC. 1EA 10+EA
GAS
SPRING
TAMURA ot 6 Digit, non-resettable
24VDC impulse counter. Plastic case
snap-in mounts into a 1" X 17/32"
cutout. 4in. leads. All are set around
999XXX to allow testing of equipment
once installed.
24VDC IMPULSE
COUNTER
W: 1-1/16" H: 7/8" D: 1-3/8" WT: .04
15551-MI Tamura Counter
$3.95 $3.50
STOCK # DESC. 1EA 5+EA
MFG: BUEHLER
P/N: 1.61.046.514.01
COIL: 12-24VDC
USED, Gearhead DC motor rated:
450RPM @ 24V, .08A NL,1.5A Stall
225RPM @ 12V, .06A NL, .8A Stall
5mm dia. X 13mm flatted steel shaft. 3 metric (M3)
threaded mounting holes. 3" leads.
12V @ 225RPM
GEARHEAD MOTOR
L: 2-3/4"(Body) DIA: 1-3/8" WT: .4
17131-MD 225RPM/12V Motor
$14.95 $12.95
STOCK # DESC. 1EA 10EA
MFG: HSI
P/N: 20841-05-028
TYPE: 2 Phase Bi-Polar 4 lead
COIL : 5VDC/18ohms/5.5mH/.27A
LINEAR STEP: .001
Linear actuator/step motor with rotating, 9/64" (.140")
Dia. X 2-5/8" steel shaft. 1-1/4" max travel.1-3/64"
(1.031") mounting ctrs. 20" leads. Shaft end thread: 2-
56 UNC 2A X .15" long
17284-MS HSI 5V Linear Actuator $9.95
STOCK # DESC. 1EA
L: 3-1/2" O/A W: 1-5/16" O/A WT: .06
5V DC STEP MOTOR
WITH LEADSCREW
MFG: BUEHLER
P/N: 1.13.022.212.04
COIL: 12-24VDC
USED DC motor assembly rated:
Approx. 104RPM @ 24V, .05A NL,1.7A Stall
51 RPM @ 12V, .04A NL, .86A Stall
Motor assembly with brass worm gear driving two
plastic gears. Last gear has a 5/16" Dia. X 5/16" plastic
nib. to provide recripcating action. 1/2" radius of rotation
on nib. Steel mounting bracket. 3" leads.
MOTOR/GEAR
ASSEMBLY
L: 5-1/4"(O/A) W: 3-1/4" (O/A) H: 1-3/4" WT: .62
17132-MD 51RPM/12VDC Motor
$19.95
STOCK # DESC. 1EA
MECHANICAL
Visit www.mpja.com for our Complete Products Lines.
TECH. & INFO: CALL 561-848-8236 FAX [phone] [e-mail]
45
MFG: SHINANO KENSHI
P/N: STP-57D211
COIL: 3.84VDC/4.7 ohms/.8A
TYPE: 2 Phase Uni-Polar 5 lead
STEP ANGLE:1.8 deg (Motor)
6.5mm dia. X 18mm steel shaft with a 3/4” dia., 16 tooth,
plastic cog belt gear attached by a steel roll pin. Ball
bearings, 3" leads, 4 corner mounting holes, Remov-
able anti vibration rubber/steel mtg. bracket. 4" leads.
17607-MS 3.84VDC Stepmotor
$9.95
STOCK # DESC. 1EA
L: 2" Body Sq.: 2-3/16" WT: 1.5
3.84V
STEPMOTOR
MFG: SHINANO KENSHI
P/N: STP-57D505
COIL: 5.3VDC/1A
TYPE: 2 Phase Uni-Polar 5 lead
STEP ANGLE:1.8 deg (Motor)
Assembly#: 127K18074
Step motor & gear assembly for copy machine. Motor
has 7mm steel shaft with a pressed on aluminum spur
gear. Removable gear unit contains 5 various plastic
gears, 2 have mechanical unidirectional clutch. 5in.
17461-MS Stepmotor Assembly
$14.95
STOCK # DESC. 1EA
Motor: L: 3" Sq.: 2-1/4" WT: 2.3
Assembly: L: 4-3/4" W: 5-1/4" H: 2-7/8" WT: 2.9
MOTOR/GEAR
ASSEMBLY
USED Motor assembly with a
Buehler 1.16.025.031.00 motor
driving a 6 piece plastic gear
train. Center driven, 6-7/8" long output shaft drives two
1-5/16"Dia. off center plastic cams attached near ends.
Approx. 116 RPM @ 12VDC. 5-1/4" C/C distance on
cams. We guess that it was part of a paper feed.
"PICKER" MOTOR
ASSEMBLY
W: 6-7/8" O/A L: 3-1/2" H: 2-1/2" WT: .34
17266-MD "Picker" Motor Asm. $12.95 $9.95
STOCK # DESC. 1EA 10EA
ENM T33 series low power, Non-Resetable Time meter.
7digit, crystal contolled impulse counter. Black Face
with White & Red numbers, Max 99999.99 hrs. 24VDC
Operation, 10mW draw. Snap-in, front mounts in 1.18"
X .51 cutout. 11" leads
24VDC RUNNING
TIME METER
17906-MI 24VDC ENM Time Meter $14.95 $12.95
STOCK # DESC. 1EA 5EA
W: 1-1/4" H: 9/16" D: 1-7/16" WT: .05
360
O
WEB
360
O
VIEW
@MPJA.COM
NEW
LOWER
PRICE