60" INDOOR / OUTDOOR LED FAN LED CEILING FAN INSTRUCTION MANUAL
WE WANT YOU TO LOVE YOUR NEW FAN SO WE’RE HERE IF YOU HAVE A QUESTION, NEED SOME HELP OR WANT TO CHAT ABOUT OUR PRODUCTS. SEND SUGGESTIONS OUR WAY TOO—WE’RE ALWAYS LOOKING TO MAKE YOUR EXPERIENCE WITH A POSITIVE ONE. This manual contains complete instructions for the installation and operation of this fan. It has been designed to make the installation process as easy as possible. If you are unfamiliar or uncomfortable with wiring, please contact a qualified electrician.
TABLE OF CONTENTS 02 GENERAL INSTALLATION & OPERATING INSTRUCTIONS 10 INSTALLING THE MONTING PLATE 03 IMPORTANT SAFETY PRECAUTIONS 11 INSTALLING THE LED ASSEMBLY AND GLASS SHADE 03 TOOLS & MATERIALS REQUIRED 12 INSTALLING THE FAN WITHOUT THE LIGHT KIT (OPTIONAL) 04 UNPACKING YOUR FAN 13 INSTALLING THE WALL CONTROL 05 PREPARATION 15 OPERATION 05 INSTALLING THE HANGING BRACKET 17 CARE AND CLEANING 06 HANGING THE FAN 17 TROUBLESHOOTING 08 ELECTRICAL CONNECTIONS 18 ENERGY GUIDE 0
GENERAL INSTALLATION & OPERATION INSTRUCTIONS 1 2 02 | To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly before beginning. To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring. All electrical connections must be made in accordance with local codes, ordinances and/or the National Electric Code.
IMPORTANT SAFETY PRECAUTIONS WARNINGS: • Disconnect power by removing fuse or turning off circuit breaker before installing the fan and/or optional lighting. • Support directly from building structure. • To reduce the risk of fire, electric shock, or personal injury, mount to outlet box marked "acceptable for fan support" and use mounting screws provided with the outlet box. Most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced.
UNPACKING YOUR FAN UNPACK YOUR FAN AND CHECK THE CONTENTS. • Do not discard the carton. If warranty replacement or repair is ever necessary, the fan should be returned in original packing. Remove all parts and hardware. Do not lay motor housing on its side, or the decorative housing may shift, be bent or damaged. • Examine all parts.
PREPARATION PREPARATION: Canopy Verify you have all parts before beginning the installation. Check foam insert closely for missing parts. Remove motor from packing. To avoid damage to finish, assemble motor on soft padded surface or use the original foam inset in motor box. Yoke cover Downrod Motor Housing DO NOT LAY MOTOR HOUSING ON ITS SIDE AS THIS COULD RESULT IN SHIFTING OF MOTOR IN DECORATIVE ENCLOSURE. Blade LED Light Kit Parts identification on assembled fan.
HANGING THE FAN 1 Remove ball from downrod by loosening set screw in the side of the ball. Slide ball down and remove ball pin; remove ball. (Fig. 1) 2 Carefully support fan body (motor) in its styrofoam packing with the mounting collar (where the wires come out) facing upward. 3 Loosen the two security set screws and remove the downrod pin and retaining clip from the coupling on top of the motor assembly. (Fig.
REMEMBER to turn off the power before you begin. Safety Cable To properly install your ceiling fan, follow the steps below. Ball Moisture Cap 6 Slip the yoke cover, trim ring and canopy onto the downrod. (Fig. 3) 7 Slide the hanger ball onto the downrod, insert the cross pin through the downrod and tighten. Tighten the set screw. 8 Feed wires through holes in rubber ball moisture cap and slide cap down over top of ball. (Fig.
ELECTRICAL CONNECTIONS REMEMBER -Turn off the power! NOTE - Control must be installed within 30 feet of fan. WARNINGS: Check to see that all connections are tight, including ground, and that no bare wire is visible at the wire nuts, except for the ground wire. BLK (AC IN) CAUTION: To reduce the risk of electric shock, this fan must be installed with an isolating wall control/switch. WH (AC IN) Insert the receiver into the ceiling mounting bracket with the flat side of the receiver facing the ceiling.
FINISHING THE INSTALLATION 11 Tuck connections neatly into ceiling outlet box. 22 Slide the canopy up to mounting bracket and place the key hole on the trim ring the screw on the mounting bracket, turn canopy until it locks in place at the narrow section of the key holes. 3 Ceiling Fan Outlet Box Hanger Bracket Align the circular hole on canopy with the remaining hole on the mounting bracket, secure by tightening the two set screws.
INSTALLING THE BLADES NOTE: Remove any rubber supports that are installed for shipping. CAUTION: Remove the two rubber packing mounts from the fan motor assembly and discard prior to attaching the blades. Insert the blade through the slot on the housing. Align the holes on the blade and the fan motor assembly and secure with the blade support plates and blade attachment screws.
INSTALLING THE LED ASSEMBLY AND GLASS SHADE NOTE: Be sure the power is off before installing. 1 Remove one of the three screws on the adapter plate located on the fan motor. Loosen the other 2 screws. (Do not remove) (Fig. 2) 2 While holding the LED assembly under your fan, make the polarized plug connections: (Fig. 2) - Red to white - Black to black 3 Tuck connections neatly into adapter plate.
INSTALLING THE FAN WITHOUT THE LIGHT KIT (OPTIONAL) Mounting Hub (bottom of motor) Adapter Plate B Screws Fig. 1 12 | Metal Cover Fig. 2 1 Remove one of the three screws on the mounting hub located on the fan motor. Loosen the other 2 screws. (Do not remove) (Fig. 1) 2 Place the key holes on the adapter plate B over the 2 screws previously loosened, turn the adapter plate until it locks in place at the narrow section of the key holes.
INSTALLING THE WALL CONTROL REMEMBER to turn off the power before you begin. NOTE - Secures to any surface or application: flat wall, single gang box, multi gang box. Option 1. Flat Surface Installation 1 Select a desired location. Use the wall plate to mark the location of the mounting holes. Plastic wall anchors or mounting screws are needed for this application. (Fig. 1) 2 Seat the cradle B into the wall plate. Secure the wall plate to the wall using the provided hardware.
Option 3. Multi Gang Wall Switch Box Installation Outlet box 1 Remove the existing wall plate and old switch from the wall outlet box. (Fig. 3) 2 Connect the black lead wires from the switch in the cradle A to the black wires in the switch box. Hot input wire to one of the cradle switch leads. Power lead to the fan is connected to the remaining switch lead. (Fig. 4) Cradle A Face plate Transmitter 3 Attach the cradle A to the wall switch box using the supplied hardware.
OPERATION Your DC brushless motor is equipped with an automatically learned type remote control. There is no frequency switches on the receiver or transmitter. The fan can start to use once the pairing process is done. Remove the panel from the transmitter and then install one 2032 battery (included). You need to use a coin to open or close the battery cover. To prevent damage to transmitter, remove the battery if not use for long periods of time (Fig. 1) WARNING: Chemical Burn Hazard.
Summer Mode and Winter Mode Operation 1 IMPORTANT: To prevent damage or cause injury, be sure that fan is switched to off and blades have stopped moving completely before attempting to change direction of rotation. 2 The reverse switch is located on the top of the motor housing. Slide the switch to the right for winter mode operation. Slide the switch to the left for summer mode operation. Make sure switch is not stuck between forward and reverse positions.
CARE AND CLEANING Periodically it may be necessary to re-tighten blade to blade arm screws or blade arm to motor screws to prevent clicking or humming sound during operation. This is especially true in climates with broad temperature and humidity ranges. When dusting the blades, you must support the blade to prevent bending - no pressure should be applied to the blades. If you experience any flaws in the operation of your fan, please check the following points.
ENERGY GUIDE SPECIFICATIONS AVERAGE PERFORMANCE AND ENERGY INFORMATION PERFORMANCE SPECIFICATIONS Estimated Yearly Energy Cost $5 $3 $34 Cost Range of Similar Models (19” – 84”) Airflow LOW SPEED Airflow (CFM) 6324 2648 Cubic Feet Per Minute Energy Use (Watts) 26.6 2.9 • The higher the airflow, the more air the fan will move • Airflow Efficiency: 273 Cubic Feet Per Minute Per Watt Airflow Efficiency (CFM/W) 238 919 Energy Costs (Yearly) $5 $1 Amps 0.0 0.0 RPMs 0 0 ftc.
SMART BY BOND SMART FAN OPTIONS: In addition to the included wall control, you can control your fan through the Bond app. • To use the app, download it for free from the App Store or Google Play. • Open the app to create your account. You can also login with your Facebook or Google account. • Next, set up a WiFi connection. You will need the SSID and WiFi password for the network you want to connect to. • Brute Force Method a) Turn mains power OFF to the fan. b) Turn mains power back ON on the fan.
