User Instructions

VARIABLE - tone Pairing (can switch the tone through the MUSIC button)

(1) Plug-in the receiver, long press the receiver “VOLUME” button until the receiver beeps once,

which mean receiver get into pairing mode;

(2) Separate sensor and magnetic stripe once, the receiver will beeps twice with LED indicator

flashes 1 second;

(3) Separate sensor and magnetic stripe once again, the receiver will beeps once with LED

indicator flashes 1 second;

(4) Short press the receiver "VOLUME" button, done.

Adding the additional door sensors/receivers please according to the above steps.

Note: When the door chime enters the pairing state, short press any key on the door chime

receiver or leave it 20 seconds without any operation, the door chime will exit the pairing

state.

FIXED - tone Pairing (only play your saved tone)

(1) Plug in the receiver and press the “VOLUME” button to select a tone that you like;

(2) Long press the receiver “VOLUME” & “MUSIC” button for about 5-7 seconds until the

receiver beeps once, which mean receiver get into pairing mode;

(3) Separate sensor and magnetic stripe once, the receiver will beeps twice with LED indicator

flashes 1 second;

(4) Separate sensor and magnetic stripe once again, the receiver will beeps once with LED

indicator flashes 1 second;

(5) Short press the receiver “VOLUME” button , done.

Adding the additional door sensors/receivers please according to the above steps.

Note: When the door chime enters the pairing state, short press any key on the door chime

receiver or leave it 20 seconds without any operation, the door chime will exit the pairing

state.

Reset the receiver(s) - Clear all settings

Unplug the receiver, then long press and hold "VOLUME" button and plug in the outlet, you will

start to hear continuous beeping and the LED light will flash ten times. Keep on pressing and

holding the "VOLUME button until there is no more sound and light, the receiver and

transmitters are now all reset.

If you want to set different tones for different sensors, you need to reset the receiver(s) first and

then pair them in FIXED - tone Pairing way :

Pair the receiver(s) and sensors and set different tones for the sensors

(1) Clear all settings;

(2) Press the receiver "MUSIC" button to select a tone that you like;

(3) Long press the receiver “VOLUME” & “MUSIC” button for about 5-7 seconds until the

receiver beeps once;

(4) Separate sensor and magnetic stripe once, the receiver will beeps twice with LED indicator

flashes 1 second;

(5) Separate sensor and magnetic stripe once again, the receiver will beeps once with LED

PAGE 1
VARIABLE - tone Pairing (can switch the tone through the MUSIC button) (1) Plug-in the receiver, long press the receiver “VOLUME” button until the receiver beeps once, which mean receiver get into pairing mode; (2) Separate sensor and magnetic stripe once, the receiver will beeps twice with LED indicator flashes 1 second; (3) Separate sensor and magnetic stripe once again, the receiver will beeps once with LED indicator flashes 1 second; (4) Short press the receiver "VOLUME" button, done.
PAGE 2
indicator flashes 1 second; (6) Short press the receiver “VOLUME” button , done; (7) Then on this receiver to choose a different tone for the other one sensor and following the above pairing instructions to make them paired is fine. For example You bought 2 pack SECRUI M508+D017 door sensor chime.
PAGE 3
2 Receivers + 2 Sensors (activate either door sensors and both receivers will ring): Same tones for different sensors (e.g.
PAGE 4
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.