EVT-AH16-VT2Q 1U Rack-Mount 16-Channel Active Balun Hub Manual Transmits up to 5,000ft (1.5km) for color 16 Local loop out 32 Outputs total Rack or wall mountable, stackable Fits in standard IT racks Adjustable contrast and brightness at each port 12~24 VAC/VDC Removable terminal blocks Built-in video surge protection Note: Model numbers that end with “Q” or that have a round green “Q” sticker signify RoHS-compliant products.
ENFORCER 1U RACK-MOUNT 16-CHANNEL ACTIVE VIDEO BALUN HUB Table of Contents: Introduction .....................................2 Features .........................................2 Parts List ........................................3 Specifications ................................. 3 Overview ........................................ 3 Shelf/Table Mounting......................4 Wall Mounting ................................ 4 Rack Mounting............................... 4 Wiring ...........................
ENFORCER 1U RACK-MOUNT 16-CHANNEL ACTIVE BALUN HUB Parts List: Rack-mount balun hub ................................................................................... x1 Cable management brackets .......................................................................... x2 M3x6 Cable bracket screws ........................................................................... x4 Mounting brackets .......................................................................................... x2 Rubber feet ......
ENFORCER 1U RACK-MOUNT 16-CHANNEL ACTIVE VIDEO BALUN HUB Shelf/Table Mounting: 1. Units may be stacked one on top of the other, or with other equipment. 2. Make sure the rubber feet are firmly attached to the mounting points on the bottom of the unit. Mounting point Rubber foot Wall Mounting: 1. Remove the mounting screws from the mounting points. 2. Screw the mounting brackets on, facing downward. 3. Use screws or bolts (not included) to mount the unit in the desired location.
ENFORCER 1U RACK-MOUNT 16-CHANNEL ACTIVE BALUN HUB Wiring: 1. Connect the included 12VDC adapter to the EVT-AH16-VT2Q and to a power source. 2. Run a Cat 5e/6 UTP cable from each camera through the wall or through a conduit to the EVT-AH16-VT2Q. Note: If existing telecom or data UTP cables are available, they can be mixed and matched with new cables. Running two or more cables together should not affect the video signals. 3.
ENFORCER 1U RACK-MOUNT 16-CHANNEL ACTIVE VIDEO BALUN HUB Connecting to Ground: 1. For best surge protection results, connect the included ground wire to the ground screw located on the back of the EVT-AH16-VT2Q. 2. Connect the ground wire to earth ground. (For example, a grounded metal conduit, a cold water pipe, or a grounding rod.) To earth ground Adjusting the Image: 1. Locate the camera’s corresponding output on the front of the EVT-AH16-VT2Q. 2.
ENFORCER 1U RACK-MOUNT 16-CHANNEL ACTIVE BALUN HUB Sample Application: 1 Local display 2 EVT-PB1Q 3 EVT-TB1-42TQ EVT-AH16-VT2Q 5 DVR 4 MVD-V1501-1Q Local display Remote displays 1. The EV-2615-NKEQ NVD Dome Camera is connected to the EVT-AH16-VT2Q through the EVT-TB1-42TQ Active Balun Transmitter. 2. The EV-2615-NKEQ NVD Dome Camera is connected to the EVT-AH16-VT2Q through the EVT-PB1Q Passive Video Balun. 3. A security monitor is connected directly to the EVT-AH16-VT2Q’s video output. 4.
ENFORCER 1U RACK-MOUNT 16-CHANNEL ACTIVE VIDEO BALUN HUB Troubleshooting: The screen is blank Check that the Active Video Balun Hub is plugged in. Check that the CCTV camera is powered up. Check that the video cable connecting the camera to the hub is connected properly. Check that the cable(s) connecting the hub to the monitor, switcher, DVR, or multiplexer are connected properly. Double-check the connections to any passive or active baluns.
