SebArt professional line AngelS 30E ARF ASSEMBLY MANUAL The new AngelS 30E ARF, was designed by the 10 times F3A Italian Champion Sebastiano Silvestri, it is the replica of his 2 meter size F3A competition airplane, 3rd at the European Championships in Swiss land 2006 and 5th at the World Championships in Argentina 2007. This professional ARTF kit is the result of Sebastiano’s long research and experience in F3A and 3D.
Table of contents Table of contents...............................................................................................................……….. 2 Required radio, motor and battery.............................................................................................…. 3 Additional required items, tools and adhesives.............................................................................. 3 Warning............................................................................................
Required radio, motor and battery Radio equipment: • Minimum 4-channel radio system • 4 digital mini servo, recommended JR PROPO DS385 or DS381 • 2 servo extension 400mm, for elevator and rudder servo • 2 servo extension 100mm, for aileron servo Recommended electric motor for best performance: • Hacker A30-14L + X40 SBec-Pro controller + APC 14x8 E Recommended Li-Po battery pack for best performance: • Flight Power EVO 2170-3S .….for unlimited 3D • Flight Power EVO 2500-3S.…..
Before starting assembly Before starting the assebly of your AngelS 30E, remove each part from its bag and protection for a prior inspection. Closely inspect the fuselage, wing panels, rudder, and stabilizer for damage. If you find any damage or missing parts, contact the place of purchase. If you find any wrinkles in the covering, use a heat gun or covering iron to remove them. Use caution while working around areas where the covering material overlap to prevent separating the covers.
Section 1 – ailerons installation step 1 Trial fit the four aileron hinges, included in the hardware pack, in their place and verify the correct position and alignment of the aileron with the wing panel. step 2 Carefully glue, with some drops of thin CA, each of the four hinges in the aileron. step 3 Locate the aileron and carefully glue, with some drops of thin CA, the hinges into the wing panel.
step 4 Work the aileron up and down some times to work the hinges and check for proper movement. step 5 Repeat steps 1 through 4 for the remaining wing panel. Section 2 – aileron servo & control horn installation step 1 Locate the following items included in the hardware pack and the servo. step 2 Install the servo hardware (gommets and eyelets) and put the servo into the wing panel, as per pictures.
step 3 Drill using a 1,5mm drill bit, and install the servo into the wing panel using a Phillips screwdriver. step 4 Glue the fibreglass horn with medium CA into the aileron. step 5 Install the hardware and make the final adjustment as per pictures. step 6 Repeat steps 1 through 5 for the remaining wing panel.
Section 3 – rudder installation & tail wheel installation step 1 Locate the items included in the hardware pack and assemble them as per picture. step 2 Locate the following items. step 3 With the hobby knife cut a groove of 15mm length into the rudder. Drill in the rudder, 15mm from the bottom, the location for the tail wheel using a 2mm drill bit.
step 4 Drill the screw locations for the tail wheel using a 1,5mm drill bit, and install it as per picture. step 5 Locate the rudder in his place and check the alignment with the fuselage. Right after glue the rudder with some drops of medium CA,as per pictures. step 6 Insert the three hinges in their appropriate slots of the rudder, and glue them with some drops of thin CA.
step 7 Carefully put some drops of medium CA into the 2 mm hole into the rudder. Carefully locate the rudder and glue the hinges with some drops of thin CA. step 8 Work the rudder right and left some times to work the hinges and check for proper movement. Section 4 – elevator installation step 1 Insert in the elevator the four hinges into their appropriate slots and verify the correct position and alignment of the elevator with the stabilizer.
step 2 Carefully glue the hinges, with some drops of thin CA, in the elevator only. Than insert carefully the elevator through the fuselage. step 3 Insert the stabiliser into fuselage space and check the alignment with the wing carbon tube. step 4 Locate the elevator hinges into the stabiliser. Glue carefully the hinges in the stabiliser with some drops of thin CA.
step 5 Once satisfied with the alignment, glue carefully with thin CA the stabilizer at the fuselage. Section 5 – elevator servo & control horn installation step 1 Locate the following items included in the hardware pack, servo extension 400mm long and servo. step 2 Than install the servo hardware (gommets and eyelets) and locate the servo into the fuselage.
step 3 Drill using a 1,5mm drill bit, and install the servo into the fuselage using a Phillips screwdriver. step 4 Glue the fibreglass horn with medium CA into the elevator. Than install the hardware and make the final adjustment as per picture. Section 6 – rudder servo & control horn installation step 1 Locate the following items included in the hardware pack, servo extension 400mm long and servo.
step 2 Than install the servo hardware (gommets and eyelets) and locate the servo into the fuselage. step 3 Drill using a 1,5mm drill bit, and install the servo into the fuselage using a Phillips screwdriver. step 4 Glue the fibreglass horn with medium CA into the elevator. Than install the hardware and make the final adjustment as per picture.
Section 7 – landing gear & wheels installation step 1 Locate the following items included in the hardware pack. step 2 Install wheel and wheel pant as per pictures.
step 3 Locate the landing gear on the fuselage and fix it with the 3 screws included in the hardware pack. step 4 Test fit the L.G. Lift Generator and his alignment with the fuselage.
step 5 Glue carefully the landing gear fillet with some drops of medium CA, as per picture. step 6 Repeat steps 2 to 5 for the other side of the landing gear.
step 1 Locate the motor and fix it with the four screws included in the motor hardware pack. step 2 Locate and fix the ESC and his switch as per picture.
step 3 Glue with some drops of medium CA the Velcro strip included in the hardware pack. step 4 Fix carefully the prop and spinner. Section 9 – small wings installation (optional) We recommend to install this small wings (included in the kit) to improve the aerobatic capability of your AngelS 30E. step 1 Locate the following parts included in the kit.
step 2 Install the fuselage small wing, gluing the parts with some drops of medium CA, as per pictures. step 3 Install on both wing panels the small deflectors, gluing the parts carefully with some drops of thin CA, as per pictures.
Section 10 – final radio installation Install the receiver, two extension 100mm for aileron servos and the battery pack as per the picture. Wings installation Locate the wing panels and fix them using the two nylon screws, included in the hardware pack, and a Phillips screwdriver.
Control throws Please, follow carefully the recommended linkage setups for ailerons and elevators.
¾ 140mm is good for pattern flying. ¾ 150mm is good for 3D flying. Use the Flight Power battery pack, moving it forward or backward, to achieve the correct balance. A Flight Power 3s 2150 for more agility and a 3s 2500 for precision and sports flying. Range test your radio • Before fly, be sure to range check your radio as manufacturer’s instruction manual of you radio-system recommand. • Double-check all controls (aileron,elevator, rudder and throttle) move in the correct direction.
www.sebart.
