005600PMA0
1005600PMA0 This page is intentionally left blank
SeaSTAR 3610 USER MANUAL Notice to Customers This manual has been produced to ensure the very best performance from your SeaSTAR receiver. The manual has been clearly set out with simple instructions to ensure trouble free usage of your SeaSTAR receiver. This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these changes will be incorporated in new editions of the manual.
SeaSTAR 3610 USER MANUAL Dealer Information _______________________________________________ Cit y _______________________________________________ Address _______________________________________________ State ________________________________________________ Post Code _____________ __________________________________ Countr y _______________________________________________ Phone _______________________________________________ Fax _______________________________________________ Email __________
SeaSTAR 3610 USER MANUAL One-Year Limited Hardware Warranty Fugro Seastar AS and its operating companies world-wide (SeaSTAR), warrants this product to be free from defects in workmanship and material for a period of one year from the date of original sale by Fugro Seastar AS or its iiinauthoriz dealers, to the original purchaser or end user.
SeaSTAR 3610 USER MANUAL Issue 1.0 Issue 1.1 Issue 1.2 Issue 2.0 Issue 2.1 Issue 2.2 Issue 2.3 REVISION HISTORY April 2009 First issue May 2009 Minor corrections November 2009 References to G2 added. PDF version of user manual now on CD rather than USBstick. WEEE info inserted. February 2010 NTRIP and FTP functionality added Contact info on initial subscription added Menu interface layout added Default settings added Misc corrections March 2010 Minor corrections.
SeaSTAR 3610 USER MANUAL ACRONYMS USED IN THIS MANUAL CE CEMF C/N C/N0 DGPS DGNSS DHCP DPS EN G2 GPS GLONASS HP IEC IP LAN LED LNA NCC NMEA 1005600PMA0 NTRIP RF RoHS RTCM SCF TCP UDP WEEE WGS84 DOP GGA VBS FTP Communauté Européenne Counter Electro-magnetic Force Carrier to Noise ratio Carrier to normalised Noise ratio Differential GPS Differential Global Navigation Satellite System Dynamic Host Configuration Protocol Differential Positioning Sensor European Norm High Precision GPS&GLONASS Global Positio
SeaSTAR 3610 USER MANUAL TABLE OF CONTENTS INTRODUCTION......................................................................................................... 1 ABOUT THIS MANUAL.................................................................................................... 1 SYSTEM FEATURES...................................................................................................... 1 SYSTEM COMPONENTS ..........................................................................................
SeaSTAR 3610 USER MANUAL APPENDIX E - MENU STRUCTURE ....................................................................... 35 ABOUT MENU ............................................................................................................ 35 STATUS MENU - CHANNEL A, CHANNEL B.................................................................... 36 STATUS MENU - NTRIP ............................................................................................. 37 STATUS MENU - VBS ...................
SeaSTAR 3610 USER MANUAL 1005600PMA0 This page left intentionally blank viii Issue 2.
SeaSTAR 3610 USER MANUAL INTRODUCTION This manual has been produced to assist the typical user with the installation and operation of the 3610 DGNSS receiver. About this manual This manual is organised into the following chapters: Chapter 1 Introduction - A brief presentation of the manual and system features. Chapter 2 Getting started – Describes how to get started with the 3610 DGNSS receiver as quickly as possible. Chapter 3 Modes of operation setup – Description of the different operation modes.
SeaSTAR 3610 USER MANUAL The signals are received via the antenna/DGNSS receiver. After selection of the desired individual reference site's data set, the signals are made available as corrections for use in a GPS and GLONASS differential capable receiver. The 3610 DGNSS receiver supports the following SeaSTAR services: 1. 2. 3. 4. 5. SeaSTAR HP SeaSTAR G2 SeaSTAR XP SeaSTAR DGNSS SeaSTAR VBS SeaSTAR HP is a decimetre level phase-based service.
SeaSTAR 3610 USER MANUAL System components A standard delivery of the 3610 DGNSS receiver with a spotbeam antenna consists of the following parts: 1. 2. 3. 4. 3610 DGNSS receiver unit Coax cable RG-58 – N-male to N-female, 1 m Coax cable RG-58 – TNC-male to N-female, 1 m 2 x RS-232 serial cables LIYCY 3 x 2 x 0.14 mm2, 9-pin DSub male to 9-pin DSub female, 2 m length 5. RS-422 serial cable, 9-pin DSub male to 5-pin Weidmuller female, 2 m length 6. LAN cable, shielded, 3 m length. 7. Power supply 85 VAC...
SeaSTAR 3610 USER MANUAL GETTING STARTED The purpose of this section is to get you started with the 3610 DGNSS receiver as quickly as possible. When the receiver is supplied to you, it will be configured with default factory settings. This means that you need to configure the receiver and get a subscription before it can deliver useful corrections. In addition, you also need to connect the appropriate cables and apply power to the receiver (and antenna).
SeaSTAR 3610 USER MANUAL The receiver will indicate frequency searching by displaying "Init" on the signal status page. When it has locked to the signal, “Sync” and finally "Lock" will be displayed. Signal strength will also be indicated by a bar graph display and C/N ratio. Should the “Lock” indicator fail to be displayed after 30 – 90 seconds, check through steps 1 to 4 above.
SeaSTAR 3610 USER MANUAL MODES OF OPERATION SETUP Set the receiver to the required mode; DGNSS, HP/XP/G2 or VBS. Note! During certain situations it may take up to 40 min before normal operation is achieved with regard to output of correctional data. Reasons for this include: First time power-up. The unit has been moved for a longer distance without having GPS track. Without power for a longer period of time.
SeaSTAR 3610 USER MANUAL link), and receiver location entered via the display configuration menu or through the GGA message via a GPS receiver. In VBS mode, the RTCM data will appear on the output ports A and/or B or LAN. Default port settings are initially configured, and will by default change based upon the type of subscription. If different port settings are needed, the ports will need to be set up to match the requirements of your GPS receiver RTCM ports.
SeaSTAR 3610 USER MANUAL RECEIVER INTERFACES Power The 3610 DGNSS receiver will operate on any DC voltage between 9 VDC and 24 VDC. When operational, the unit dissipates typical 9 W (max 12 W) of power. Power is connected to the unit via a 1.5 metre long red/black lead. The cable is terminated with a 6-pin Hirose LF07WBP-6S female connector. Red is +Vin and black is -Vin. The connector pin layout is illustrated in Figure 4. Left is as viewed from the female mating side, and right is solder side. Figure 4.
SeaSTAR 3610 USER MANUAL Serial lines The panel connectors for serial port A and B are DB9 female. Pin layout is described below: Pin no. 1 2 3 4 5 6 7 8 9 Signal RS-422 TX+ RS-232 TXD RS-232 RXD Not in use GND RS-422 TXNot in use RS-422 RX+ RS-422 RX- Table 2 Serial line pin layout Special serial cables are supplied with the DGNSS receiver. The cables are terminated as described below.
SeaSTAR 3610 USER MANUAL The table below describes the automatic serial port configuration, depending on the type of subscription: Subscription type H : HP L : L1 I : IONO G : GLONASS V : VBS R : RAW (SCF) Serial port A Serial port B X X X X X X UDP ports The Ethernet connector is a standard RJ45 Ethernet connector with two LEDs. Shielded Ethernet cables can be used to connect to this port. The Ethernet interface provides the possibility to send corrections on four different UDP ports.
SeaSTAR 3610 USER MANUAL MENUS AND DISPLAYS General The 3610 DGNSS receiver has an internal display with two lines x 16 characters. There are six buttons on the keypad; ESC, , , , and (Enter). The button is used to confirm user input and settings. It is also used to select a page. The ESC button is used to exit pages without changing settings, while the Arrow buttons are used to turn pages and to set parameters.
SeaSTAR 3610 USER MANUAL Alarm situations The 3610 DGNSS receiver has two LED indicators, one green for power indication and one red for alarm indication. The red LED will be lit continuously or flash if one of the situations below arises. The LED will be turned off if the situation which activated the alarm becomes OK, for example if lock on signal, upgrade of software is finished. The alarm situation will, however, be stored in the Status menu.
SeaSTAR 3610 USER MANUAL Main pages Signal status The Signal status page is the top page in the 3610 DGNSS receiver. This page is displayed after start up, and is at the top level of the menu structure. About From the About menu it is possible to read receiver type, serial number, software version and subscription expiry date. It is also possible to reset receiver and select factory default. No configurations from these pages are possible.
SeaSTAR 3610 USER MANUAL Signal status The Signal status page for the 3610 DGNSS receiver indicates signal strength, which satellite the receiver is set to, the lock criteria and available subscriptions. After power on, the receiver will begin to search for a DGNSS satellite. "Init" will be displayed at the bottom right of the screen when the receiver is in search mode. When the receiver locks to a signal, "Lock" will be displayed instead. If a signal is lost after being locked, "Sync" will be displayed.
SeaSTAR 3610 USER MANUAL I : IONO G : GLONASS V : VBS R : RAW (SCF) About When pressing arrow down in the Signal status page, the Main menu with its main pages appears. The About menu shows information about the 3610 DGNSS receiver. The DGNSS receiver type, serial number and software version are displayed. Main Menu About In addition, the subscription expiry date of the DGNSS service is displayed. The serial number (Sno) of the unit is important when contacting Fugro SeaSTAR for subscription requests.
SeaSTAR 3610 USER MANUAL The NTRIP page displays if the NTRIP is active or not, the NTRIP IP address, the NTRIP port and the NTRIP mountpoint (satellite). The VBS page displays if an input from an external GPS receiver is available, and the status of the input data. Information available is the quality of the service: Q1 (GPS) or Q2 (DGPS), number of satellites, DOP, data age of the corrections and the latitude/longitude values that are input.
SeaSTAR 3610 USER MANUAL The Use Channel menu makes it possible to select which channel to use, if both channel A and channel B are selected in the Ch. Option menu. From the Channel page it is possible to set the satellite service, frequency and symbol rate. Note that the satellite service choice will not be available before a satellite list is downloaded. From the NTRIP page it is possible to set NTRIP enable/disable, IPaddress to server, user name and password.
SeaSTAR 3610 USER MANUAL From the FTP menu it is possible to configure FTP user name and FTP password. Port Cfg FTP Set GPS L1 sites menu From this menu the GPS L1 reference stations which shall be output, are set. These settings are only in use when a GPS L1 subscription is enabled. Main Menu Set GPS L1 Site The site list containing the reference stations must be available from the satellite before the stations are shown. If they are not available, “No station list” will be shown.
SeaSTAR 3610 USER MANUAL The following options may be selected: On/off/nearest It is possible to set all GLO L1 sites on or off, or only to use the nearest stations. How many of the nearest stations to use, is configurable. Factory default value is 32. When using the nearest sites option, it is important to insert the position into the receiver. The position is set in the Set Pos/Ch menu, or through port A or B as a GGA message.
SeaSTAR 3610 USER MANUAL 3610 DGNSS RECEIVER AND DPS SETUP EXAMPLE The 3610 DGNSS receiver may be used together with a variety of DPS systems: DPS 116, DPS 122, DPS 132, DPS 200, DPS 232 and DPS 700. The different DPS systems use different SeaSTAR services: DPS system DPS 116 DPS 122 DPS 132 DPS 200 DPS 232 DPS 700 SeaSTAR DGNSS X X X X X X SeaSTAR Plus SeaSTAR HP SeaSTAR XP X X X X X X X X X SeaSTAR G2 X X To set up a DPS system to use Fugro SeaSTAR services do the following: 1.
SeaSTAR 3610 USER MANUAL Figure 1 Entering the DPS setup file Select System|NavEngine standard. The figure below displays a default view for the Input/Output communication before any interface details are added. Figure 2 Input/Output view before interface details are added 1005600PMA0 4. 5. 6. Select a DGNSS link and configure the I/O type to match with the output of the 3610 Demodulator. It is possible to define several correction links in the DPS and the 3610 Demodulator system.
SeaSTAR 3610 USER MANUAL 7. When selecting an interface, the Input/Output view will be divided into two sections. The upper part consists of the list with all interfaces. The lower part consists of Configuration details for the interface selected in the list. The configuration details vary between the different interfaces. Figure 3 Input/Output list view with configuration details 8. The Configuration details view is the lower part of the Input/Output list view.
SeaSTAR 3610 USER MANUAL When planning to use HP/XP/G2 corrections, the DPS must be set up and connected to the 3610 DGNSS receiver when the subscription is transmitted and enabled. 1005600PMA0 Note! 23 Issue 2.
SeaSTAR 3610 USER MANUAL 1005600PMA0 This page is intentionally left blank 24 Issue 2.
SeaSTAR 3610 USER MANUAL INSTALLATION Installation considerations Before starting installation of the 3610 DGNSS receiver on a vessel, the following should be considered: Determine the preferred location for each unit. The 3610 DGNSS receiver is designed for indoor installation. Consider cable length, connector attachment space (cable bend radius), stowing of excess cable, moisture, chemical corrosion, vibration and heat exposure.
SeaSTAR 3610 USER MANUAL If cables must cross, ensure that they cross at an angle of 90°. This minimizes the possibility of interference. As far as is practicable, ensure that cables and I/O connectors are unique and fit only in their allocated location. Try to make the coaxial cables as short as possible. Avoid routing cables along-side power generator cabling and other high electrical noise sources. This can cause interference.
SeaSTAR 3610 USER MANUAL TECHNICAL SPECIFICATIONS Radio frequencies Receiver frequency band: ................................................................ 1525 – 1559 MHz Channel bandwidth: ............................................................................................. 5 kHz Physical dimensions Width: ........................................................................................................... 109.5 mm Height: ..................................................................
SeaSTAR 3610 USER MANUAL 1005600PMA0 This page is intentionally left blank 28 Issue 2.
SeaSTAR 3610 USER MANUAL APPENDIX A Receiver service procedure If a SeaSTAR receiver unit fails to perform, contact Fugro Seastar AS, after following the procedural checks. We wish to hear about frequently experienced problems and your assistance will be appreciated. Copy the form on the next page, fill in the details requested and faxing or mailing the form to Fugro Seastar AS for forwarding to Product Marketing. The most common problems are interfacing, and usually occur at installation time.
SeaSTAR 3610 USER MANUAL 1005600PMA0 This page is intentionally left blank 30 Issue 2.
SeaSTAR 3610 USER MANUAL APPENDIX B SeaSTAR receiver problem report form Please copy this form and report the problem with as much detail as possible. Problem with: Signal Y/N SeaSTAR Y/N Date: Manual Y/N Receiver Y/N Description of problem: Person Reporting: Contact Phone #: Model #: Serial #: Customer Name: Customer Address: Customer Phone #: Date purchased: / / Dealer: GPS Receiver used: Serial #: Area of operations: 1005600PMA0 Symptoms from display (if any): 31 Issue 2.
SeaSTAR 3610 USER MANUAL 1005600PMA0 This page is intentionally left blank 32 Issue 2.
SeaSTAR 3610 USER MANUAL APPENDIX C Factory Default settings Position Lat Lon Satellite Channel A Name Frequency SymbolRate Channel B Name Frequency SymbolRate : 5955.000000 : 1038.000000 : EUSAT : 1537440000 : 2438 : AOREH : 1535125000 : 1219 Sites GPS GLONASS : 32 Nearest : 32 Nearest Antenna Antenna power : Off Serial Ports A B : 38400 baud : 38400 baud TCP/IP Address NetMask Gateway UseDHCP Port A Port A Port A Port B : 192.168.004.100 : 255.255.255.000 : 192.000.000.
SeaSTAR 3610 USER MANUAL 1005600PMA0 This page is intentionally left blank 34 Issue 2.
SeaSTAR 3610 USER MANUAL APPENDIX E - MENU STRUCTURE This section describes the menu structure in the 3610 DGNSS Receiver. About menu Main Menu About SeaSTAR 3610 Sno. 1160579 Main Menu Status SeaSTAR 3610 Ver. 2.01.03 Main Menu Set Pos/Ch SeaSTAR 3610 Subsc. HLIGV Main Menu Port Cfg SeaSTAR 3610 Exp. 4 Oct 2010 Main Menu Port Output SeaSTAR 3610 Reset Main Menu Set GPS L1 Site Main Menu Set GLO L1 Site Main Menu Display Cfg 1005600PMA0 Main Menu Backup 35 Issue 2.
SeaSTAR 3610 USER MANUAL Status menu - Channel A, Channel B Channel: A, B Status Channel A Channel A Used EUSAT ID 7 Main Menu Set Pos/Ch Status Channel B Channel A Used Serv.ID 50821 Main Menu Port Cfg Status Ntrip Channel A Used Freq. 1537.4400M Main Menu Port Output Status VBS Channel A Used Symb rate 2438 Main Menu Set GPS L1 Site Status Alarms Channel A Used Uplink TiPoAlSi Main Menu Set GLO L1 Site Status Position Channel A Used G:98.4% B:1.
SeaSTAR 3610 USER MANUAL Status menu - NTRIP Main Menu Status Status Ntrip Ntrip Option Auto Main Menu Set Pos/Ch Status VBS Ntrip Address 150.101.173.014 Main Menu Port Cfg Status Alarms Ntrip Port 2101 Main Menu Port Output Status Position Ntrip Mountpoint EUSat Main Menu Set GPS L1 Site Status GPS Time No time Ntrip No Data Main Menu Set GLO L1 Site Status Ant.power 12.
SeaSTAR 3610 USER MANUAL Status menu - Alarms Main Menu Status Status Alarms Alarm Current No Lock Main Menu Set Pos/Ch Status Position AL: 060710 12:33 Not subscribed Main Menu Port Cfg Status GPS Time No time AL: 060710 12:33 No lock Main Menu Set GPS L1 Site Status Corrections AL: 060710 13:33 Not subscribed Main Menu Set GLO L1 Site Status Ant.power 12.40V 0.
SeaSTAR 3610 USER MANUAL Main Menu Status Status Position Position Fixed LAT 6336.4900N Main Menu Set Pos/Ch Status GPS Time No time Position Fixed LON 01124.1700E Main Menu Port Cfg Status Corrections Main Menu Port Output Status Ant.power 12.40V 0.04A Main Menu Set GPS L1 Site Status Channel A Main Menu Set GLO L1 Site Status Channel B Main Menu Display Cfg Status Ntrip Main Menu Backup Cfg Status VBS Main Menu About Status Alarms 1005600PMA0 Status menu - Position 39 Issue 2.
SeaSTAR 3610 USER MANUAL Status menu - GPS Time Main Menu Status Status GPS Time No time Main Menu Set Pos/Ch Status Corrections Main Menu Port Cfg Status Ant.power 12.40V 0.04A Main Menu Set GPS L1 Site Status Channel A Main Menu Set GLO L1 Site Status Channel B Main Menu Display Cfg Status Ntrip Main Menu Backup Cfg Status VBS Main Menu About Status Alarms 1005600PMA0 Status Position 40 Issue 2.
SeaSTAR 3610 USER MANUAL Status menu - Corrections Main Menu Status Status Corrections Corrections GPS L1 sB uABD Main Menu Set Pos/Ch Status Ant.power 12.40V 0.
SeaSTAR 3610 USER MANUAL Status menu - Ant. Power Status Ant.power 12.40V Main Menu Set Pos/Ch Status Channel A Main Menu Port Cfg Status Channel B Main Menu Port Output Status Ntrip Main Menu Set GPS L1 Site Status VBS Main Menu Set GLO L1 Site Status Alarms Main Menu Display Cfg Status Position Main Menu Backup Cfg Status GPS Time No time Main Menu About Status Corrections 1005600PMA0 Main Menu Status 42 Issue 2.
SeaSTAR 3610 USER MANUAL Set Pos/Ch - Ch. Option Main Menu Set Pos/Ch Set Pos/Ch Ch. Option AB Main Menu Port Cfg Set Pos/Ch Use Channel A Main Menu Port Output Set Pos/Ch Channel A Main Menu Set GPS L1 Site Set Pos/Ch Channel B Main Menu Set GLO L1 Site Set Pos/Ch Ntrip Main Menu Display Cfg Set Pos/Ch Position Main Menu Backup Cfg Set Pos/Ch Ant.Power On Main Menu About Set Pos/Ch Ant.Power 12.40V Shown if Antenna power is set to on 1005600PMA0 Main Menu Status 43 Issue 2.
SeaSTAR 3610 USER MANUAL Set Pos/Ch - Ch. Option Main Menu Set Pos/Ch Set Pos/Ch Use Channel A Main Menu Port Cfg Set Pos/Ch Channel A Main Menu Port Output Set Pos/Ch Channel B Main Menu Set GPS L1 Site Set Pos/Ch Ntrip Main Menu Set GLO L1 Site Set Pos/Ch Position Main Menu Display Cfg Set Pos/Ch Ant.Power On Main Menu Backup Cfg Set Pos/Ch Ant.Power 12.40V Main Menu About Set Pos/Ch Ch. Option AB Shown if Antenna power is set to on 1005600PMA0 Main Menu Status 44 Issue 2.
SeaSTAR 3610 USER MANUAL Set Pos/Ch - Channel Main Menu Set Pos/Ch Set Pos/Ch Channel A Channel A Service EUSAT Main Menu Port Cfg Set Pos/Ch Channel B Channel A Freq 1537.4400M Main Menu Port Output Set Pos/Ch Ntrip Channel A Symbol rate 2438 Main Menu Set GPS L1 Site Set Pos/Ch Position Main Menu Set GLO L1 Site Set Pos/Ch Ant.Power On Main Menu Display Cfg Set Pos/Ch Ant.Power 12.40V Main Menu Backup Cfg Set Pos/Ch Ch.
SeaSTAR 3610 USER MANUAL Set Pos/Ch - NTRIP Main Menu Set Pos/Ch Set Pos/Ch Ntrip Ntrip Option Auto Main Menu Port Cfg Set Pos/Ch Position Ntrip address 150.101.173.014 Main Menu Port Output Set Pos/Ch Ant.Power On Ntrip port 2101 Main Menu Set GPS L1 Site Set Pos/Ch Ant.Power 12.40V Ntrip mountpoint EUSat Main Menu Set GLO L1 Site Set Pos/Ch Ch.
SeaSTAR 3610 USER MANUAL Set Pos/Ch - Position Main Menu Set Pos/Ch Set Pos/Ch Position Position Fixed LAT 6326.4900N Main Menu Port Cfg Set Pos/Ch Ant.Power On Position Fixed LON 0101.1700E Main Menu Port Output Set Pos/Ch Ant.Power 12.40V Main Menu Set GPS L1 Site Set Pos/Ch Ch.
SeaSTAR 3610 USER MANUAL Set Pos/Ch - Ant.Power Main Menu Set Pos/Ch Set Pos/Ch Ant.Power On Main Menu Port Cfg Set Pos/Ch Ant.Power 12.40V Main Menu Port Output Set Pos/Ch Ch. Option AB Main Menu Set GPS L1 Site Set Pos/Ch Use Channel A Main Menu Set GLO L1 Site Set Pos/Ch Channel A Main Menu Display Cfg Set Pos/Ch Channel B Main Menu Backup Cfg Set Pos/Ch Ntrip Main Menu About Set Pos/Ch Position Shown if Antenna power is set to on 1005600PMA0 Main Menu Status 48 Issue 2.
SeaSTAR 3610 USER MANUAL Port Cfg - Serial Port Main Menu Port Cfg Port Cfg Serial Port A Serial Port A Baudrate 38400 GPS L1, VBS, G2/HP/XP,GLO L1, IONO, RAW, DEBUG Main Menu Port Output Port Cfg Serial Port B Serial Port A GPS L1 No Subsc Main Menu Set GPS L1 Site Port Cfg UDP Port A Serial Port A VBS L1 No Subsc Main Menu Set GLO L1 Site Port Cfg UDP Port B Serial Port A G2/HP/XP Diasble Main Menu Display Cfg Port Cfg UDP Port C Serial Port A GLO L1 No Subsc Main Menu Backup Cfg Port Cf
SeaSTAR 3610 USER MANUAL Port Cfg - UDP Port Port:A, B, C, D Main Menu Port Cfg Port Cfg UDP Port A UDP Port A mask 192.168.000.255 Main Menu Port Output Port Cfg UDP Port B UDP Port A numb.
SeaSTAR 3610 USER MANUAL Port Cfg - TCP/IP Main Menu Port Cfg Port Cfg TCP/IP IP address 192.168.004.100 Main Menu Port Output Port Cfg FTP IP Use DHCP No Main Menu Set GPS L1 Site Port Cfg Serial Port A IP Set Static Main Menu Set GLO L1 Site Port Cfg Serial Port B IP Netmask 255.255.255.000 Port Cfg UDP Port A IP gateway 192.000.000.001 Main Menu Display Cfg Main Menu Backup Cfg Port Cfg UDP Port A IP address 192.168.004.
SeaSTAR 3610 USER MANUAL Port Cfg - FTP Main Menu Port Cfg Port Cfg FTP FTP username *** Main Menu Port Output Port Cfg Serial Port A FTP password *** Main Menu Set GPS L1 Site Port Cfg Serial Port B Main Menu Set GLO L1 Site Port Cfg UDP Port A Main Menu Display Cfg Port Cfg UDP Port B Main Menu Backup Cfg Port Cfg UDP Port C Main Menu About Port Cfg UDP Port D Main Menu Status Port Cfg TCP/IP 1005600PMA0 Main Menu Set Pos/Ch 52 Issue 2.
SeaSTAR 3610 USER MANUAL Main menu - Set GPS L1 site Main Menu Set GPS L1 Site Set GPS L1 Sites Site Nearest Main Menu Set GLO L1 Site Set GPS L1 Sites Use 32 Main Menu Display Cfg Set GPS L1 Sites Site 132 On Only shown if Site is set to ”Nearest” Main Menu Backup Main Menu About Main Menu Status Main Menu Set Pos/Ch 1005600PMA0 Main Menu Port Cfg 53 Issue 2.
SeaSTAR 3610 USER MANUAL Main menu - Set GLO L1 site Main Menu Set GLO L1 Site Set GLO L1 Site Site Nearest Main Menu Display Cfg Set GLO L1 Site Use 32 Main Menu Backup Set GLO L1 Site Site 132 On Only shown if Site is set to ”Nearest” Main Menu About Main Menu Status Main Menu Set Pos/Ch Main Menu Port Cfg 1005600PMA0 Main Menu Set GPS L1 Site 54 Issue 2.
SeaSTAR 3610 USER MANUAL Main menu - Display Cfg Main Menu Display Cfg Display Cfg Backlight On Main Menu Backup Display Cfg Contrast High Main Menu About Main Menu Status Main Menu Set Pos/Ch Main Menu Port Cfg Main Menu Set GPS L1 Site 1005600PMA0 Main Menu Set GLO L1 Site 55 Issue 2.
SeaSTAR 3610 USER MANUAL Main menu - Backup Cfg Main Menu Backup Cfg Backup Cfg Save Main Menu About Restore Cfg Restore Main Menu Status Main Menu Set Pos/Ch Main Menu Port Cfg Main Menu Set GPS L1 Site Main Menu Set GLO L1 Site 1005600PMA0 Main Menu Display Cfg 56 Issue 2.
SeaSTAR 3610 USER MANUAL APPENDIX F – DIAGNOSTIC MENU This section describes the diagnostic menu structure in the 3610 DGNSS Receiver. It is accessed by pressing and simultaneously, anywhere in the 3610 DGNSS Receiver menu. Diagnostic menu – About Diagnostics About SeaSTAR 3610 ARM 2.01.03 Diagnostics Status SeaSTAR 3610 FPGA 2.01.01 Diagnostics Config SeaSTAR 3610 FGO 3.00.
SeaSTAR 3610 USER MANUAL Diagnostic menu – Status Diagnostics Status Status Total Lock 00:00:00 Diagnostics Config Status Last Lock 00:00:00 Diagnostics Corrections Status Lost Locks 0 Diagnostics IO-Statistics Status Ntrip Restarts 0 Diagnostics Reset stat. Status Counts Good 0 Diagnostics Erase flash Status Counts Bad 0 Diagnostics DAC calibration Status C/N 0.0 dB 1005600PMA0 Diagnostics About 58 Issue 2.
SeaSTAR 3610 USER MANUAL Diagnostic menu – Config Diagnostics Config Config Factory Diagnostics Corrections Config Ser. Port Setup Manual Diagnostics IO-Statistics Config Debug Stx Off Diagnostics Reset stat. Config Debug Fgo Off Diagnostics Erase flash Config Periodic Clear all No Diagnostics DAC calibration Config Periodic Status Off Diagnostics About Config Periodic Run Status Off Diagnostics Status Config Periodic Corr Stat.
SeaSTAR 3610 USER MANUAL Diagnostic menu – Corrections Diagnostics Corrections GPS RTCM 1 Rec 0 HP Rec 0 Diagnostics IO-Statistics GPS RTCM 1 Out 0 HP Out 0 Diagnostics Reset stat.
SeaSTAR 3610 USER MANUAL Diagnostic menu – IO- Statistics Diagnostics IO-Statistics IO Stat. GPS Rec 0 IO Stat. HP Err 0 IO Stat. RAW Rec 0 Diagnostics Reset stat. IO Stat. GPS Sel 0 IO Stat. HP Tx 0 IO Stat. RAW Sel 0 Diagnostics Erase flash IO Stat. GPS Err 0 IO Stat. HP Lost 0 IO Stat. RAW Err 0 Diagnostics DAC calibration IO Stat. GPS Tx 0 IO Stat. GLO Rec 0 IO Stat. RAW Tx 0 Diagnostics About IO Stat. GPS Lost 0 IO Stat. GLO Sel 0 IO Stat. RAW Lost 0 Diagnostics Status IO Stat.
SeaSTAR 3610 USER MANUAL Diagnostic menu – Reset statistics Diagnostics Reset stat. Diagnostics Erase flash Diagnostics DAC calibration Diagnostics About Diagnostics Status Diagnostics Config Diagnostics Corrections 1005600PMA0 Diagnostics IO-Statistics 62 Issue 2.
SeaSTAR 3610 USER MANUAL Diagnostic menu – Erase flash Diagnostics Erase flash Erase flash Main image Diagnostics DAC calibration Erase flash IO image Diagnostics About Diagnostics Status Diagnostics Config Diagnostics Corrections Diagnostics IO-Statistics 1005600PMA0 Diagnostics Reset stat. 63 Issue 2.
SeaSTAR 3610 USER MANUAL Diagnostic menu – DAC calibration Diagnostics DAC calibration DAC calibration Recalibrate Diagnostics About DAC calibration Value 2448 Diagnostics Status Diagnostics Config Diagnostics Corrections Diagnostics IO-Statistics Diagnostics Reset stat. 1005600PMA0 Diagnostics Erase flash 64 Issue 2.
SeaSTAR 3610 USER MANUAL 1005600PMA0 USER NOTES 65 Issue 2.
SeaSTAR 3610 USER MANUAL SeaSTAR Customer Support and 24 Hour Help Line 1005600PMA0 FUGRO SEASTAR AS Tel: +47 21 50 14 20 Fax: +47 21 50 14 01 E-Mail: seastarservice@fugro.no 66 Issue 2.
