OWNER’S MANUAL 4 0 ” L AW N A E R ATO R MODEL: S AT- 4 0 B H • • • • Assembly Installation Operation Repair Parts For the latest product updates & setup tips: Visit us on the web! www.brinly.com Important: This manual contains information for the safety of persons and property.
INTRODUCTION CONGRATULATIONS on the purchase of your new Brinly-Hardy Lawn Aerator! Your lawn aerator is designed, engineered and manufactured to give you the best possible dependability and performance. CUSTOMER RESPONSIBILITIES Please read and retain this manual. The instructions enables you to assemble and maintain your lawn aerator properly. And please, always observe the “Safety” instructions. TABLE OF CONTENTS SAFETY .........................................................................
SAFETY TO HELP PREVENT BODILY INJURY DUE TO LOSS OF STABILITY OR CONTROL: TOWING SAFELY • Do not exceed maximum towing capacity of towing vehicle listed in the vehicle operator's manual. • Stopping distance increases with speed and weight of towed load. Travel slowly and allow extra time and distance to stop. • Do not tow this machine behind a motor vehicle such as a car, truck or ATV. • Total towed weight must not exceed limits specified in towing vehicle operator's manual.
PARTS REFERENCE TOOLS REQUIRED FOR ASSEMBLY: • 1 - Pair of work gloves • 1 - Pair of pliers • 1 - Screwdriver (flat blade) • 2 - 7/16” Wrenches • 1 - 1/2” Wrench • 2 - 3/4” wrenches EXPLODED VIEW 2 13 5 13 11 3 29 16 29 16 15 15 18 14 4 19 10 1 15 16 24 15 12 16 15 16 17 8 6 17 28 25 26 22 27 7 21 27 23 20 23 9 PARTS LIST REF 3. PART NO. DESCRIPTION QTY. REF PART NO. DESCRIPTION 1. R-821-10 Drawbar Clevis 1 15. 30M1000P Hex Nut, 5/16” 11 2.
ASSEMBLY Step 1. ATTACH END PANELS TO TRAY 1a) Attach the two End Panels (5) to the Tray (3) using six 5/16” x3/4” Rd Hd. Screws (13), 5/16” Flat Washers (29), 5/16” Lock Washers (16) and 5/16” Hex Nuts (15), as shown. 5 29 16 15 16 29 13 5/16” Lock Washer Qty. 6 5/16” Flat Washer Qty. 6 3 13 5/16” x 3/4” Rd Hd Screw Qty. 6 Step 2. INSTALL DRAWBAR 2a) Install Drawbar (4) to Tray (3) using two 5/16” x3/4” Rd Hd. Screws (13), 5/16” Lock Washers (16) and 5/16” Hex Nuts (15), as shown.
ASSEMBLY 6 Step 3. ASSEMBLE TINES TO AXLE 3a) Place a 5/8” Flat Washer, Thick (17) onto the Axle Assembly (6), then slide it through the hole in End Panel (5 right Side) and add another Flat Washer Thick (17) if needed.
ASSEMBLY Step 4. ATTACH HANDLE ASSEMBLY 4a) Attach the Handle Assembly (8) to end the of the Axle Assembly (6) by inserting one 1/4” x 1-1/4” Hex Bolt (25) though the hole in the end of the Axle Assembly) and secure with 1/4” Hex Nut(26), as shown. Note: The wheel bar mount on the Axle Assembly must be positioned downward, as shown, in order to properly attached the wheels. 4b) Slide the Handle Grip (10) on to the Handle Assembly (8). WHEEL BAR MOUNT 10 8 25 6 26 25 Hex Bolt, 1/4 x 1-1/4” Qty.
ASSEMBLY Step 5. INSTALL WHEELS 4a) Attach one Wheel (9) to the Handle Assembly (8) and the other wheel to the wheel bar mount on the Axle (6). Secure to each side using hardware in the following order: 23 • 1/2” x 3” Hex Bolt (20) • 1/2” Flat Washer (23) 21 22 Flat Washer, 1/2” Qty. 4 Hex Nut, 1/2” Qty. 4 Lock Washer, 1/2” Qty. 3 • Wheel (9) • 1/2” Flat Washer (23) • 1/2” Hex Bolt (21) • 1/2” Lock Washer (22) 20 • 1/2” Hex Bolt Hex Bolt 1/2” x 3” Qty.
ASSEMBLY Step 6. MOUNTING & TRANSPORTING 6a) Attach Aerator to your towing vehicle using Drawbar Pin (18) and Hairpin Cotter (12) supplied. 6b) To place in Transport Position: • Pull FORWARD on Handle Assembly (8). • Pull out slightly and position over Transport Lock Pin (24). Aerator rests on wheels. CAUTION: Avoid damage to tines.
OPERATION INSTALLING YOUR AERATOR OPERATING CAUTION: Avoid injury! Make sure feet and hands are clear of Tine Tips. CAUTION: Avoid injury! Avoid damage to tines. Engage the transport wheels when crossing concrete or asphalt driveways and walkways. Avoid injury! Do not operate lift handle unless attachment is installed to towing vehicle Excessive towed load can cause loss of control on slopes. Stopping distance increases with speed and weight of towed load.
SERVICE MAINTENANCE After the first 30 minutes of use check all fasteners for tightness. Tines are manufactured with galvanized steel to resist wear of abrasive soil. Striking objects can cause tines to curl or break. Contact our Customer Service Department to purchase replacement Tines (Part # B-5423). Aerator is essentially maintenance free. However as with any steel product, it can rust. Apply a light coat of oil on tines after use to prevent rust.
MANUFACTURER’S LIMITED WARRANTY FOR Pull Behind Accessories The limited warranty set forth below is given by Brinly-Hardy Company with respect to new merchandise purchased and used in the United States, its possessions and territories. Brinly-Hardy Company warrants the products listed below against defects in material and workmanship, and will at its option, repair or replace, free of charge, any part found to be defective in materials or workmanship.
