Air Conditioner Owner's Manual

ELECTRICAL CONNECTIONS
FIELD WiRiNG iNSTRUCTiONS
1.MAiN POWER SUPPLY
THiS COOLER iS PREWIRED FOR 115 VOLT OR 230
VOLT, 6OHZ POWER ONLY. MAKE SURE YOU
CONNECT YOUR COOLER TO THE CORRECT VOLTAGE.
A_
B.
Remove the control box cover- (4)screws.
Remove 2"x 4" water tight junction box (3},junction Box
Cover (5), switch (4) and 1/2_chase nipple (1) and jam
nut (2) from the parts ca_ton.
C. Mount junction box to the cooler as foffows:
D.
1_ Insert chase nipple (1)into 7/8" hole from the inside of
the cabinet (8) arid fasten it tightly to the cooler with
the 1/2" conduit jam nut (2).
2. Screwthe Junction box (3)or_totimethread of the chase
nipple (1) until tight and aligned vertically.
CAUTION; Make sure the power is off to the supply
wires before proceeding with the next steps.
Connect ground wires asfollows; Referto wiring diagram
inside the control box cover.
2.
Pull the green ground wire harness from the cooler
through the chase nipple {l).
Attach the eyelet terminal of the ground wire harness
and the ground wire from the power supply to the
disconnect box (3) usingthe #10 Green Ground screw
supplied_Attach thespade terminal of the ground wire
assembly to the switch (4) ground screw.
E. Connect Li_'_eLeads as Follows:
F,
] 5 Volts CooPers: Pull the bi_ackand white jumper
wires from the cooler through thechasenipple (1) into
the iunction box (3}. Attach the black iumper wire to
one screw terminal on the switch (4). Attach the hot
supply lead to the other screw terminal on the switch
Attach the white iumper wire from the cooler to the
white or neutral wire from the supply line using the
orange wire nut supplied.
2_
230 Volt Coolers: Pull the black and orange iumper
wires from the cooter through the chasenipple (1) into
the iunction box (3). Fastenthe black wire to one !oad
screw on the switch. Fastenthe orange iumper wire to
the other load screw on the switch_ Fasten the two
supply leads to the two line screws on the swtich.
Mount the switch (4) onto the iunction box (3) with the
on position up and the ground screw on the switch
down.
G, Mount the junction box cover (5) onto the junction box
making certain that the gasket fits properly a[[ the way
around the periphery of the iunction box (3),
INSTRUCC[ONES DE ALAMBRADO
CONEXIONES ELECTRICAS
i. FUENTE DE PODER PRINCIPAL
ESTEENFRIADOR HA SIDO ALAMBRADO PARA
OPERAR CON CORR[ENT[ DE 115 VO[TIOS 60HZ
SOLAMENTE
a.
2_
Remueva tatapadera de [a casade control- (4) tornillos.
Remueva la caia impermeable 2" x 4" de empa[me (3),
tapadera de caia (5), interruptor(4) Y el nipie de encaie
de T/2"(I )e[ niple deencaje de 1/2 °(1) contratuerca (2)
de la caia de cart6n.
Monte la caja de empalme como sigue:
Co[oque elnipie de encaje (1)en el agujero de 7/8 _'de
adentro de/gabinete(8)Yasegurelocon lacontratuerca
(2).
Atornil[e [a caja de empaime (31en [a roscade el niple
(1)basraque quede apretada y vetticatmente aiineada_
PRECAUC!ON: Asegurese que la corriente est_
desconectada antes de proceder con los siguientes
pasos,
D. Conecte los a!ambres de tierra como sigue; Yea el
diagrama de alambrado dentro de la tapadera de/a caia
de control.
2_
E_
F_
G_
)ale el alambre verde altrav_s de el niple (1)
Conecte [a terminat de oiiito deI alambre de tierra y el
alambre de tierra de la fuente de poder a la caja de
empalme (3) usando el tornillo verde de tierra #10
incluido. Conecte [a terminal de espada de[ alambre
de tierra a[ tomi/[o de tierra del interruptor (4).
Conecte Los A/ambres de La Linea de Corrieme Como
Sigue:
Enfriadoresde 115 voltios: Jalelos alambresde cierre
negro y el bianco del enfriador atrav_s del nipie (t)
hacia la caja de empaime (3)_Conecte e/alambre
negro de cierre a un tomil[o de [a terminal en el
interruptor (4). Conecte el a el
otto tomillo en [a terminal del hterruptor, Conec:te el
aiambre de cierre blanco del enfriador al alambre
b/anco o neutral de la Iinea de corriente usando el
cono aislante anaraniado proveido.
2_
Enfriadoresde 230 Vol:tios: _alelos alambresde cierre
negro y el anaraniado del enfriador atrav_s de_nip[e
(1) hacia/a caja de empalme (3), Conecte el alambre
de cierre negro a unade lasterminales decarga (Load)
del interruptor. Conecte el alambre de derre
anaranjado a [a otraterminal de carga de[ interruptor.
Conecte los dos a[ambresde corriente a[asterminales
marcadas supply (Fuente) del it'_terruptor.
Monte el interruptor (4) en [a ca]a (3) con ta posici6n de
prendido hacia arriba y el tomiHo de tierra hada abajo.
Monte la tapadera de la caja (5) asegurandose que el
empaque cierre el periferio de la caja (3).