ISearsl OWNERS MANUAL KNOW YOUR UNIT MODEL NO . Read this booklet so that you will be able to enjoy all the features of your PROG RAMMABLE SCANNING MONITOR. 934.36390600 If after installing t he Programmable Scaning Monitor, if doesn't operate properly, recheck your installation procedures and if there is still a problem, see chart on page 10. INDEX Page Explanation of Features and Controls .. . ... . ... . • Operation. . . . . . . . . . . . . • Installation... .•. . . . . . . .
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. EXPLANATION OF FEATURES AND CONTROLS CHANNEL INDICATOR VO LUME ON/OFF SWITCH SQUELCH CONTROL AUTO/MAN UAL SWI TCH VOLUME ON/OFF SWITCH Turn clockwise to apply power to the unit and then adjust for desired sound level. SQUELCH CONTROL Th is control cuts off or el iminates annoying background noise in the absence of an incoming signal.
••••••••• EX TE RNAL SPEAKER JACK GRO UN D TERM INAL AC POWER SOCKET DC POWE R SOCKET PROGRAM CARD SLOT Insert your program card into this slot. For programming desirable frequencies on the program card refer to "Program Card Programming" in the other booklet provided and titled as "CODE BOOK", CHANNEL SKIP BUTTONS These skip buttons are provided to turn each individual channel on or off.
EXTERNAL SPEAKER JACK You can connect an external speaker (8 ohm) to this jack for remote listening (Built-in speaker is then disconnected automatically) . AC POWER SOCKET Can accept 120V AC. DC POWER SOCKET Connect the Red wire to the Positive (+) side of 12V DC power supply or battery and the Black wire to the Negative (-) side. Before attempting this, be sure to read "Installation" instructions. OPERATION 1. Set all CHANNEL SKIP BUTTONS to on position (button out). 2.
INSTALLATION HOME INSTALLATION No special mounting is required for indoo r use. The unit is designed for shelf or table·top operation. Connect the AC power cord and antenna to the appropriate jacks. To receive weak signals from a distant station, an outdoor-type external antenna may be required. An antenna tuned to the desired f requency bands is recommended. For best performance, the antenna shou Id be mou nted as high as practical. See your Sears store for available antenna models.
POWER CONNECTION FOR NEGATIVE GROUND VEHICLES Vehicle with negative ground will have the negative (-) terminal connected directly to the frame or chassis of the veh icle. Vehicles with positive ground will have the positive (+) terminal connected directly to the frame of chassis of the vehicle. DO NOT USE WITH POSITIVE GROUND SYSTEM. Connect the Red wire (with in-line fuse holder) to the Accessory terminal on the ignition switch of your vehicle.
OFFICIAL NATIONAL TEN CODE SIGNALS TH E LAW concerning possession and use of monitor receivers is embodied in Federal regulations based on Section 605 of the Communications Act of 1934. This FCC regulation does not prohibit listening to Public Service Band frequencies. It does prohibit persons from making use of information heard on Public Service Bands, for private gain. Some State laws prohibit the use of mobile monitors except by authorized vehicles.
10-84 10-85 10-86 10-87 10-88 10-89 10-90 10-91 If meeting ... advise ETA Delayed due to ... Officer operator on duty Pick up checks for distribution Advise present telephone number of .. . Bomb threat Bank alarm at ...
SYMPTOMS AND SOLUTIONS Before returning set for a malfunction be sure to check this chart for solutions check. SOLUTIONS Th is set requ ires at least 12.1 volts ON/OFF Switch and Volume D .C. input, but for best p erformance Power Cord Connec tion 13.8 volts D .C. is neede d (a fully Power Cord Fuse Squelch Cont rol is Set Properly charged car battery).
SPECIFICATIONS Frequency Ranges Sensitivity Sequelch Sensitivity Selectiv ity I F Frequency Modu lation Band w idth Audio Output Speaker Antenna impedance Power Requirement OimeQsions Weight VHF LOW 30.000 - 50.000 MHz VHF HIGH 150.000 - 170.000 MHz UHF 450.000 - 469.995 MHz UHF 470.000 - 489.995 MHz UHF 490.000 - 510.000 MHz VHF 0.5pV fo r 10 dB S + N/N UHF 0.8pV for 10 dB S + N/N VHF 0.6pV UHF 0.8pV 45 dB (± 25 KHz) 10.695 MHz 1st IF 2nd IF : 455 KHz ± 7 KHz 1.5W (THO 10%) 2W (Maximum) 3-1/8" (S cm).
