Operator’s Manual 3/8-in. Variable Speed / Reversible 9 Cordless Drill / Driver 1 3 5 7 9 1 3 5 7 Model No. 172.10300 9.6 Volt Model No. 172.10400 12.0 Volt 96 ® C US 3025736 Conforms to UL 60745-1 and UL 60745-2-1 Certified to CAN/CSA-C22, 2NO.60745-1-04, NO.60745-2-1-04 LIS T E D CHARGE BATTERY BEFORE FIRST USE CAUTION: Read, understand and follow all Safety Rules and Operating Instructions in this Manual before using this product. Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
SAFETY SYMBOLS TABLE OF CONTENTS Warranty……………........................................................…………………………..Page 2 Safety Symbols……........................................................……………………….….Page 3 Safety Instructions…........................................................………………………….Pages 4 - 10 Unpacking ………….........................................................………………………….Page 11 Description ......................................................
SAFETY INSTRUCTIONS ! SAFETY INSTRUCTIONS cont. WARNING: BE SURE to read and understand all instructions in this manual before using this drill / driver. Failure to follow all instructions may result in electric shock, fire and/or serious personal injury. WORK AREA SAFETY 1. Keep your work area clean and well lit. Cluttered workbenches and dark areas invite accidents. 2. DO NOT operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
SAFETY INSTRUCTIONS cont. SAFETY INSTRUCTIONS cont. ELECTRICAL SAFETY ! WARNING: BE SURE to read and understand all instructions before operating this drill/driver. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury. A battery operated tool with integral batteries or a separate battery pack must be recharged only with the specified charging stand/transformer for the battery.
SAFETY INSTRUCTIONS cont. SPECIFIC SAFETY RULES FOR CORDLESS DRILL / DRIVERS cont. 14. Do not charge battery pack in a damp or wet location. Following this rule will reduce the risk of electric shock. 15. For best results, your battery pack should be charged in a location where the temperature is more than 50°F but less that 100°F. Do not store battery outside or in vehicles. 16. Under extreme usage or temperature conditions, battery leakage may occur.
PACKING LIST: 1. Drill / Driver with Battery Pack (in Drill) 7 9 2. Charging Stand / Transformer n Companio 1 ! WARNING: Some dust created by using power tools contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. • Crystalline silica from bricks and cement and other masonry products. • Arsenic and chromium, from chemically treated lumber.
DESCRIPTION cont. DESCRIPTION KNOW YOUR CORDLESS DRILL / DRIVER (Fig. 1) NOTE: Before attempting to use this product, familiarize yourself with all operating features and safety rules.
OPERATION OPERATION cont. FORWARD / REVERSE SELECTOR SWITCH with POWER LOCK-OFF (Fig. 2) CHARGING THE BATTERY PACK (Fig. 4 and 4a) Fig. 2 The battery pack for this tool has been shipped in a low charge condition to prevent possible problems. Therefore, you should charge overnight prior to use. a. POWER LOCK-OFF b. c. FORWARD NOTE: Batteries will not reach full charge the first time they are charged. Allow several cycles (operation followed by recharging) for them to become fully charged.
OPERATION cont. OPERATION cont. CHARGING THE BATTERY PACK cont. (Fig. 4 and 4a) ELECTRIC BRAKE 8. The battery pack will become slightly warm to the touch while charging. This is normal and does not indicate a problem. 9. Do not place the charging stand/transformer in an area of extreme heat or cold. It will work best at normal room temperature. 10. When battery pack becomes fully charged, unplug charging stand/ transformer from power supply and remove the battery pack.
OPERATION cont. OPERATION cont. KEYLESS CHUCK (Fig. 7) 15 PLUS 1 ADJUSTABLE TORQUE CLUTCH (Fig. 9, 9a and 9b) The drill/driver has a keyless chuck which allows you to hand tighten or loosen accessory bits without the use of a chuck key. 1. Grasp and hold the rear chuck collar with one hand (see Fig. 7). 2. Rotate the front of the chuck with your other hand, clockwise (as viewed from the front of the chuck), to CLOSE the chuck jaws and tighten (”GRIP”) the accessory bit in the jaws. 3.
OPERATION cont. OPERATION cont. 1. Lock the trigger switch Off by placing the Forward / Reverse Selector Switch with Power Lock-Off in the Center position. 2. Open or close the chuck jaws to a point where the opening is slightly larger than the bit size you intend to use. Also, raise the front of the drill slightly to keep the bit from falling out of the chuck jaws (see Fig. 11 and 12). 3. Insert the accessory bit. 4. Rotate the chuck clockwise to tighten (GRIP) the chuck jaws securely on the bit.
MAINTENANCE OPERATION cont. OPERATION AS A SCREWDRIVER (Fig. 15) Fig. 15 Turn and set the torque clutch collar to the desired torque setting, 1 through 15. Install and tighten the desired fastener accessory bit into the chuck. 1. Install the battery pack into the drill/driver. 2. Push the forward/reverse selector switch to the forward position. 3. Follow the guidelines on page 19 to arrive at the proper torque setting for your job. 4.
MAINTENANCE ACCESSORIES cont. Fig. 18 TO RETIGHTEN A LOOSE CHUCK (Figs. 18 and 18a) The battery pack for this tool is equipped with nickel-cadmium rechargeable batteries. Length of service from each charging will depend on the type of work you are doing. 9 The chuck may become loose on the spindle and develop a wobble. Also, the chuck screw may become loose, causing the chuck jaws to bind and prevent them from closing.
PARTS LIST cont. PARTS LIST 3/8-IN. VARIABLE SPEED / REVERSIBLE CORDLESS DRILL / DRIVER Model No. 172-10300 9.6 Volt 26 3/8-IN. VARIABLE SPEED / REVERSIBLE CORDLESS DRILL / DRIVER Model No. 172-10300 9.6 Volt Item No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 36 37 38 41 42 43 44 45 46 47 48 49 50 51 52 53 Parts No.
PARTS LIST cont. PARTS LIST 3/8-IN. VARIABLE SPEED / REVERSIBLE CORDLESS DRILL / DRIVER Model No. 172-10400 12.0 Volt 28 3/8-IN. VARIABLE SPEED / REVERSIBLE CORDLESS DRILL / DRIVER Model No. 172-10400 12.0 Volt Item No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 36 37 38 41 42 43 44 45 46 47 48 49 50 51 52 53 Parts No.
NOTES NOTES 30 31 10-4-07 Drill 10300-10400
Get it fixed, at your home or ours! Your Home For expert troubleshooting and home solutions advice: www.managemyhome.com For repair – in your home – of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner’s manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters.
