AV-SAL-01 Solar Area Light Installation & Service Manual Version 2.
AV-SAL-01 Solar Area Light 140watt multicrystalline solar module UV-stabilised LEXAN® polycarbonate lens containing 8 ultra-high intensity LEDs for optimal area illumination (>120 degrees) Adjustable light arm Positive o-ring sealing Galvanised post AL-01 light head Membrane vent Anti-tamper fittings Battery section
AV-SAL-01 Solar Area Light Table of Contents Introduction...........................................................................................Page 4 Operating Principle..............................................................................Page 4 Technology............................................................................................Page 4 AV-SAL-01 Model..................................................................................Page 5 Installation & Assembly................
AV-SAL-01 Solar Area Light Introduction Congratulations! By choosing to purchase an Avlite light, you have become the owner of one of the most advanced solar LED airfield lights in the world. Avlite Systems draws on more than 25 years experience in the design and manufacture of navigation aids, and particular care has been taken to ensure your light gives years of trouble free service.
AV-SAL-01 Solar Area Light AV-SAL-01 Model Avlite’s state-of-the-art Solar Area Light provides users with the perfect solution for lighting remote locations such as shelters, car parks and maintenance areas where connection to power grids is unfeasible. The assembly uses the latest technologies in Light Emitting Diodes (LEDs) as a light source, and provides excellent illumination over a wide projected area.
AV-SAL-01 Solar Area Light Fig 2. AL-01 Light Head Latest products and information available at www.avlite.
AV-SAL-01 Solar Area Light SPECIFICATIONS•* AV-SAL-01 Light Characteristics Light Source LED Life Expectancy (hours) 8 ultra-high intensity white (warm daylight) LEDs >50,000 Total Luminous Flux (lm) Luminous Efficiacy (lm/W) 1360 69.7 Photometry Electrical Characteristics Voltage (V) Current (A) Power (W) Power Factor Circuit Protection Temperature Range 12 1.7 20 1.
AV-SAL-01 Solar Area Light Installation & Assembly Wind Loading Avlite Systems’ panel mounting post is designed to meet wind loading requirements of AS1170.2 for Region A, B & C, Terrain Category 2 in accordance with the design requirements of AS4676. For detailed information regarding wind load regions and wind loading in general refer to AS1170.2. Regions are marked with the letters A (A1 to A5), B, C and D.
AV-SAL-01 Solar Area Light Region A Region A covers most of Central and Southern Australia, including Tasmania. 1. Assembly of the lamp post is shown in Figure 5. 2. Electrical wiring of the Solar Area Light is shown in Figure 6. 3. Recommendations for mounting of the completed lamp post assembly are shown in Figure 4. 4.
AV-SAL-01 Solar Area Light Product Components Unpack your area light and check the contents of the package. Verify that all components and hardware have been received. Please contact your Avlite office if any components are missing or damaged. Item Description Quantity 1 Area Light 1 2 120W Solar Panel 1 3 Light Arm 1 4 Main Pole 1 5 Battery Housing 1 Fig 5. AV-SAL-01 Solar LED Area Light Components & Lamp Post Assembly Latest products and information available at www.avlite.
AV-SAL-01 Solar Area Light Assembly Before installing the area light, please read the section on wind loading and ensure that the installation will be suitable. Before installing the foundations, please consider the layout of the light arm location, solar panel direction required and the mounting foot print of the battery housing. Ensure that the prepared foundations are suitable to withstand the wind loading and comply with local laws. Bolt the area light pole to the battery housing.
AV-SAL-01 Solar Area Light Fig 6. Solar Area Light Electrical Wiring Diagram Latest products and information available at www.avlite.
AV-SAL-01 Solar Area Light Activation Charging the Battery New lights should be left in the sun for 1-2 days to ensure battery is charged before placing in service. Please note, light will re-charge even when toggle switch is turned to ‘OFF’ position. Preferred Installation Location For best light performance, ensure solar modules are not covered and are in clear view of the sky with no shadows. Light Operation 1. The AV-SAL-01 will be preset at the factory to steady-on. 2.
AV-SAL-01 Solar Area Light Regulator Connection & Operation Fit the Morning Star SS10 regulator into the carrier on the back wall. Fit the two 55 amp hour battery’s in to the shelves in the battery housing. Important: The regulator has a connection sequence that must be followed. Please ensure the regulator is connected in the following sequence. 1. Connect Battery Negative cable to the battery negative terminals on the batteries 2.
AV-SAL-01 Solar Area Light Maintenance & Servicing Designed to be maintenance free, the AV-SAL-01 requires minimal attention, though the following maintenance and servicing information is provided to help ensure the life of your Avlite product. 1. Cleaning Solar Panels - occasional cleaning of the solar panels may be required. Using a cloth and warm soapy water, wipe off any foreign matter before rinsing the panels with fresh water. 2.
AV-SAL-01 Solar Area Light Trouble Shooting Problem Remedy Light will not activate. • • • • Light will not operate for the entire night. • Expose light to direct sunlight and monitor operation for several days. Avlite products typically require 1.5 hours of direct sunlight per day to retain full autonomy. From a discharged state, the light may require several days of operational conditions to ‘cycle’ up to full autonomy.
AV-SAL-01 Solar Area Light Notes Latest products and information available at www.avlite.
AV-SAL-01 Solar Area Light Avlite Light Warranty V1.1 Activating the Warranty Upon purchase, the Avlite Systems warranty must be activated for recognition of future claims. To do this you have two (2) options: 1. Postal Registration Please complete the Avlite Systems Warranty Registration Card and return to Avlite within 30 days of your purchase. 2. Online Registration Please complete the Online Registration Form at; www.avlite.
AV-SAL-01 Solar Area Light 5. No modifications to the original specifications determined by Avlite shall be made without written approval of Avlite Systems. 6. Avlite lights can be fitted with 3rd party power supplies and accessories but are covered by the 3rd party warranty terms and conditions. 7. The product must be packed and returned to Avlite Systems by the customer at his or her sole expense. Avlite Systems will pay return freight of its choice.
AV-SAL-01 Solar Area Light Other Avlite Products Available Solar Aviation Lighting Radio Controlled & PALC Systems (FCC Compliant) Obstruction Lighting (LIOL A & LIOL B) Airfield Markers & Accessories Typical Applications • Temporary & permanent airfield lighting • Remote, emergency & defence airfield lighting • Barricade, hazard & perimeter lighting • Obstruction Lighting Area & Sign Lighting For a complete list of product compliances including ICAO & FAA, please contact Avlite today Head Office A
