Long Hand Sealer Models: WN-500H/HC, WN-650H/HC, WN-750H/HC, WN900H/HC, WN-1000H/HC, WN-1300H, WN-1500H/HC Distributed By: Version 1.
Copyright © 2015 by Stephanie Hwang All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, or other electronic or mechanical methods, without the prior written permission of the publisher, except in the case of brief quotations embodied in critical reviews and certain other noncommercial uses permitted by copyright law.
W H L H I N S T R U C T I O N M A N U A L General Information Thank you for purchasing our W-Series Long Hand Sealers. This owner’s manual contains information relating to your sealer. The manual will provide you with basic information concerning both operation and maintenance of your new machine. Please read it carefully as failure to do so may result in bodily injury and/or damage to the equipment. Please fill in the information below. You will find the information on the machine identification plate.
W H L H I N S T R U C T I O N M A N U A L Safety Instructions WARNING! Below are general safety precautions and warnings that should be understood prior to setting up or operating your equipment. Read and fully understand all instructions and warnings prior to using this unit. Your safety is most important! Failure to comply with procedures may result in serious injury or property damage. Remember: Your personal safety is your responsibility.
W H L H I N S T R U C T I O N M A N U A L Never touch the heating elements with hand while the sealer is plugged into a power source, in operation or just finished operation. Touching heated areas may cause fire and/or severe burns. The blade found on the Long Hand Sealer w/ Cutter is very sharp. Use extreme caution when handling or changing the blade. While machine is in operation, do not place fingers, tools, or other foreign objects on or into the machine.
W H L H I N S T R U C T I O N M A N U A L Introduction W-Series Long Hand sealers are designed for sealing longer materials for specialized sealing needs. Our W-Series Long Hand sealers w/ cutters are accompanied with a sliding cutter ideal for sealing or making bags from poly tubing. The sealers can seal polyethylene, polypropylene, saran, nylon, static shielding bags, and Mylar up to 10mil in total thickness.
W H L H I N S T R U C T I O N M A N U A L Getting to Know your Long Hand Sealer W-Series Long Hand Sealers are simple and efficient sealing machines. Sealing Arm Bring sealing arm to activate sealing process Cutting Bracket w/ Blade Units with Cutter(HC) can cut ~3/4” from seal Timer Adjustable timer for various material thicknesses Sealer Base Place material to be sealed on sealer base Figure 1.
W H L H I N S T R U C T I O N M A N U A L Figure 2.
W H L H I N S T R U C T I O N M A N U A L Electrical Circuit Diagram Figure 3.
W H L H I N S T R U C T I O N M A N U A L Operating your Sealer Assembly Instructions Sealer comes assembled and ready to operate. Operation 1. Before operating, check the heating element, PTFE cover, PTFE adhesive and the silicone rubber. The heating element should be intact. 2. Insert the power cord into the correct receptacle (110V). 3. Turn the power switch on. 4. Set the timer knob to the lowest setting. Always start with a low setting and increase gradually as needed. 5.
W H L H 6. I N S T R U C T I O N M A N U A L When replacing the heating elements, always replace the PTFE adhesive under the heating element. A worn PTFE adhesive can cause the heating element to break prematurely. The PTFE adhesive works as a barrier between the body of the sealer and the element. Never allow the element to come in direct contact with the sealer body as that will damage the timer. 7. Occasionally check the condition of the silicone sponge/compression foam for wear or burns.
W H L H I N S T R U C T I O N M A N U A L Maintenance The following maintenance procedures should be followed to ensure the longevity of your W-Series Long Hand sealer. Inspection and Cleaning 1. Inspect your machine daily. 2. Use a clean cloth to remove any plastic residue remaining on the top PTFE cloth. 3. When replacing the elements, always check the condition of the bottom PTFE adhesive. 4. Check the condition of the silicone rubber for wear and burns.
W H L H I N S T R U C T I O N M A N U A L To install your replacement kit on your sealer, turn off power and unplug sealer. Removing Worn Parts 1. Remove the heating element cover (Figure 4). 2. Loosen the screws on the PTFE cover plate (Figure 5). Figure 5. Remove PTFE cover plate Figure 4. Remove heating element cover 3. Lift up the PTFE cover to expose the heating element. 4.
W H L H I N S T R U C T I O N M A N U A L 3. Place a new element on top of the PTFE adhesive by fitting one eyelet of the heating element on one mounting spring followed by the other mounting spring. Using a screwdriver to flex the mounting spring inward will ease the placement of the element on the mounting spring. Check the element to ensure it is tight and intact. 4. Cut off any worn out PTFE cover.
W H L H I N S T R U C T I O N M A N U A L Figure 11. Carefully remove the old blade. Figure 10. Remove cutter protector. 3. Replace the old blade with a new blade. Replace cutter protector and screw back into place. 4. Slide the cutting bracket back on the silicone bracket. Install the spacer, washer and screw to hold the silicone bracket in place.
W H L H I N S T R U C T I O N M A N U A L Parts Diagram Figure 12.
W H L H I N S T R U C T I O N Item M A N U A L Part # Description Comments REPLACEMENT KITS Includes (2) elements, (2) PTFE adhesives, 1ft PTFE Cover, and blade if cutter unit (HC) specify model # when ordering 1 Base specify model # when ordering 2 Square Tube for WHLH and WHI specify model # when ordering RKs 2a RK-Model# WHI-65 3 4 Spring for Square Tube for WHLH and WHI Sealing Bar / Upper Arm specify model # when ordering SRS-specifymodel# Silicone Sponge, Compression Foam SR-WN
W H L H I N S T R U C T I O N Item M A N U A L Part # Description 40 WHLH-40 Bushing for Screw 41 MS-WHLH Spring Hook, Mounting 41a HTA-WH Spring Hook Assembly (includes 41,42,59) HTAB-WH-bracket Heating Terminal Block for WN-1500H / WN-1500HC 42 WHLH-42 Solderless Terminal 2-8 / Connecting Plate 43 Screw-M4x8 M4*8 Screw 44 WHLH-44 Hexagon Bolt M6*16 45 Hexagon Bolt 3/8*13/4 46 Screw M3*15 47 WHA-15 Multi Star Knob (W-Series) 48 WHA-14 Plate for PTFE Sheet (Clip) (W-Series
W H L H I N S T R U C T I O N M A N U A L Troubleshooting Problem Possible Causes Solution No sealing Timer lights off 1. Disconnected power cord 2. Power cord is broken 3. Blown fuse 4. Transformer is broken 1. Check or change plug 2. Replace power cord 3. Replace fuse 4. Replace the transformer No sealing Timer lights are on 1. Heating element is broken 2. Poor contact at heating terminal assembly 1. Replace the heating element 2.
