Specifications
RN: 2-31
RS3: Software Release Notes for P1 R4.2
Software and Hardware Requirements
Table 2.29. I/O Requirements for P1/V18 Combined PeerWay Image Designation (continued)
Type
Supported by
Controller
Images
Use the
following
FIC/FIM
software
image
Minimum
Required
Part NumberDescription
Type
Supported by
Controller
Images
Use the
following
FIC/FIM
software
image
S-RevF-Rev
Part NumberDescription
1984--4418--0001
1984--4418--0004
1.1 3.3
MAO
MAIO Output
F
I
M
10P54080004
(EMC Approved)
4.1 3.3
$$MAIO3_3
$MPC2+_18
$MPC2+
_
P1
M
A
O
F
I
M
10P58080005
(Replaces
10P54080004)
(EMC Approved)
5.1 3.3
$
$
M
A
I
O
3
_
3
$
M
P
C
2
+
_
P
1
$MPC5_P1
1
9
8
4
4
0
8
0
0
0
0
1
1
1
3
4
$
$
D
I
O
3
4
M
D
I
O
L
o
w
S
i
d
e
1984--4080--0001
1.1 3.4
$$DIO3
_
4
MDIO
M
D
I
O
L
ow
S
i
d
e
Switch
10P53520006 (EMC
Approved)
6.6 4.0
$
$
D
L
H
4
0
$MPC2+_18
$MPC2+_P1
$
M
P
C
5
P
1
MDIO High Side
Switch
10P53550006 (EMC
Approved)
6.7 4.0
$$DLH4
_
0
$
M
P
C
5
_
P
1
1
9
8
4
2
5
4
6
0
0
0
1
1
1
5
N
/
A
1984--2546--0001
1.15 N
/
A
PIOB Pulse I/O
1984--2546--0002
10P54470002 (EMC
Compliant)
12P25960002 (EMC
Compliant)
1.15
*
N/A
-- -- --
$$MPCAP18
$MPC2+_18
$MPC2+_P1
$MPC5_P1
TIB
Temperature
Input
1984--2731--0001
1.8 3.1
$$TFIC3_1
$$MPCAT18
$MPC2+_18
$MPC2+_P1
$MPC5_P1
(1)
Supports Contact FlexTerm (1984--1336--000x or 1984--1175--000x) that require the Contact Controller
(CC) Image. A Contact FlexTerm can be cabled to a ControlFile MultiPurpose Controller (MPC(I),
MPCII, or MPC5) jumpered to the CC image, or to a Contact Controller.
(2)
Supports Contact Card Cage (1984--2576--0001) that require the MultiPurpose Controller images. A
Contact Card Cage can be cabled only to a ControlFile MPC Controller (MPC(I), MPCII, or MPC5).
* The minimum acceptable firmware is shown. A higher level firmware of 2.07 is shipping with newer pulse
cards.
NOTES:
D
F--REV is the Boot ROM in the I/O card.
D
S--REV is the downloadable image stored on the I/O card’s battery--backed memory or flash memory. This software
can be upgraded, if required