NVR-xU NVR-xUD Network video recorder User´s manual i
Table of Contents 1 Features and Specifications ..................................................................................................................... 1 1.1 Overview .............................................................................................................................................. 1 1.2 Features ............................................................................................................................................... 1 1.3 Specifications .......
4.4.3 Image ................................................................................................................................ 4.4.4 Channel Name ................................................................................................................. 4.4.5 Upgrade ............................................................................................................................ 4.4.6 UPNP ........................................................................................
.9 Backup ..................................................................................................................................... 141 4.9.1 File Backup ....................................................................................................................... 141 4.9.2 Import/Export .................................................................................................................... 143 4.9.3 Backup Log ...............................................................
4.14.1.2 BPS ........................................................................................................................... 190 4.14.1.3 Online User .............................................................................................................. 190 4.14.1.4 Remote Device Information ................................................................................... 191 4.14.1.5 Remote ................................................................................................
5.8.2.7 DDNS ........................................................................................................................ 225 5.8.2.8 IP filter ...................................................................................................................... 226 5.8.2.9 Email ........................................................................................................................ 227 5.8.2.10 UPnP ................................................................................
5.8.5.3.1 Display .................................................................................................................... 260 5.8.5.3.2 Tour ......................................................................................................................... 260 5.8.5.4 Alarm Out ................................................................................................................. 261 5.8.5.5 Default ................................................................................
Important Safeguards and Warnings 1．Electrical safety All installation and operation here should conform to your local electrical safety codes. The product must be grounded to reduce the risk of electric shock. We assume no liability or responsibility for all the fires or electric shock caused by improper handling or installation. 2．Transportation security Heavy stress, violent vibration or water splash are not allowed during transportation, storage and installation. 3．Installation Keep upwards.
Keep away from extreme hot places and sources Avoid direct sunlight Keep away from extreme humid places Avoid violent vibration Do not put other devices on the top of the NVR Be installed in well ventilated place; do not block the vent.
1 Features and Specifications 1.1 Overview This series NVR is a high performance network video recorder. This series product support local preview, multiple-window display, recorded file local storage, remote control and mouse shortcut menu operation, and remote management and control function. This series product supports centre storage, front-end storage and client-end storage. The monitor zone in the front-end can be set in anywhere.
Network Monitor Through network, sending audio/video data compressed by IPC or NVS to client-ends, then the data will be decompressed and display. Support max 128 connections at the same time. Transmit audio/video data by HTTP, TCP, RTP/RTCP and etc. Transmit some alarm data or alarm info by SNMP. Support WEB access in WAN/LAN. Adopt the video compression and digital process to show several windows in one monitor.
Type Video Decode Capability Max 2-ch 1080P 30fps Video Input 4/8-ch network compression video input Video Output 1-channel VGA analog video output HDMI 1-ch HDMI output. Version number is 1.4 Window Split 1/4/8-window or 4-ch 720P 30fps or 8-ch D1 30fps N/A Audio Audio Input N/A Audio Output Alarm Funciton Port and Indicator Audio Compression Standard G.711a Alarm Input N/A Alarm Output N/A Storage 1 built-in 2.
Network Connection 1 RJ45 10/100Mbps self-adaptive Ethernet port. PoE N/A Power Port 1 power socket. Power adapter power supplying mode. DC 5V 2A power. 1 power socket. Power adapter power supplying mode. DC 48V 1.25A power. Power Button N/A Power Button On-off IR Receiver Window N/A N/A Clock Built-in clock. Indicator Light General N/A Power Consumption 10W (Exclude HDD) Working Temperature 10 Working Humidity 55 10℅ 90℅ Air pressure 86kPa 106kPa Dimension 191.8mm×128.2mm×35.
1.3.2 NVR-401U/801U Series System Decode Video System Resources 4/8-ch series product support 4/8 HD connection respectively. Total bandwidth supports 28/56Mbps respectively. OS Embedded Linux real-time operation system Operation Interface WEB/Local GUI Video Type H.264/MJPEG Decode Decode Capability Max 2-ch 1080P 30fps Video Input 4/8-ch network compression video input Video Output 1-channel VGA analog video output HDMI 1-ch HDMI output. Version number is 1.
Port and Indicator Multiple-Chann el Playback Max 8-channel D1 or 4-channel 720P or 2-channel 1080P playback RS232 Port N/A RS485 Port N/A 2 peripheral USB2.0 ports. USB Port Network Connection 1 RJ45 10/100Mbps self-adaptive Ethernet port. PoE N/A Power Port 1 power socket. Power adapter power supplying mode. DC 12V power. 1 power socket. Power adapter power supplying mode. DC 48V power. Power Button N/A Power Button On-off IR Receiver Window N/A N/A Clock Built-in clock.
Dimension 205mm×206.75mm×45.2mm Weight 0.5kg 1kg (Exclude HDD) Installation Mode Desk installation 1.3.3 NVR-1001U Series System Decode Video System Resources 4/8/16-ch series product support 4/8/16 HD connection respectively. Total bandwidth supports 28/56/80Mbps respectively. OS Embedded Linux real-time operation system Operation Interface WEB/Local GUI Video Type H.
Audio Alarm Funciton Port and Indicator Audio Input 1-ch bidirectional talk input Audio Output 1-ch bidirectional talk output Audio Compression Standard G.711a Alarm Input N/A Alarm Output N/A Storage 1 built-in SATA port Multiple-Chann el Playback Max 4-channel 1080P playback RS232 Port N/A RS485 Port N/A USB Port 2 peripheral USB2.0 ports. Network Connection 1 RJ45 10/100Mbps self-adaptive Ethernet port. PoE Port N/A Power Port 1 power socket.
Dimension 205mm×206.75mm×45.2mm Weight 0.5kg 1kg (Exclude HDD) Installation Mode Desk installation 2 Front Panel and Rear Panel 2.1 Front Panel 2.1.1 NVR-401U/801U Series The front panel is shown as in Figure 2-1. Figure 2-1 Please refer to the following sheet for detailed SN information. Name Function 1 HDD status indictor light The red light becomes on when HDD is abnormal. 2 Power indicator light The red light becomes on when the power connection is OK.
2.1.2 NVR-1001U Series The front panel is shown as below. See Figure 2-3. Figure 2-3 Please refer to the following sheet for detailed information. SN Name Function 1 Network status indicator light The red light becomes on when the network connection is abnormal. 2 Power indicator light The red light becomes on when the power connection is OK. 3 HDD status indictor light The red light becomes on when HDD is abnormal.
2.2 Rear Panel 2.2.1 NVR-xUD Series The rear panel is shown as below. See Figure 2-10. Figure 2-10 Port Name HDMI Connection Function USB2.0 port USB2.0 port. Connect to mouse, USB storage device, USB burner and etc. Network port 10M/100Mbps self-adaptive Connect to the network cable. High Definition Media Interface High definition audio and video signal output port. It transmits uncompressed high definition video and multiple-channel data to the HDMI port of the display device.
Port Name Connection Function VGA VGA video output port VGA video output port. Output analog video signal. It can connect to the monitor to view analog video. Power socket. Power input port input DC 5V/2A. 2.2.2 NVR-401U/801U Series The rear panel is shown as below. See Figure 2-12. Figure 2-12 Please refer to the following sheet for detailed information. Port Name Connection Function USB2.0 port USB2.0 port. Connect to mouse, USB storage device, USB burner and etc.
Port Name Connection Function HDMI High Definition Media Interface High definition audio and video signal output port. It transmits uncompressed high definition video and multiple-channel data to the HDMI port of the display device. HDMI version is 1.4. VGA VGA video output port VGA video output port. Output analog video signal. It can connect to the monitor to view analog video. GND Ground end Power socket. Power input port , input DC 12V/2A.
. Port Name Connection Function USB2.0 port USB2.0 port. Connect to mouse, USB storage device, USB burner and etc. Network port 10M/100Mbps self-adaptive Connect to the network cable. HDMI High Definition Media Interface High definition audio and video signal output port. It transmits uncompressed high definition video and multiple-channel data to the HDMI port of the display device. HDMI version is 1.4. VGA VGA video output port VGA video output port. Output analog video signal.
2.3 Alarm Connection 2.3.1 Alarm Port The alarm port is shown as below. See Figure 2-38. The following figure is based on the another series. Figure 2-38 Icon Function 1 16 ALARM1 ALARM16. The alarm becomes activated in the low level. NO1 C1 NO2 C2 NO3 C3 NO4 C4 Four NO activation output groups. (On-off button). NO5 C5 NC5 One NO/NC activation output group. (On-off button). CTRL 12V Control power output. Disable power output when alarm is canceled. Current is 500mA. 12V Rated current output.
Figure 2-39 Note There are two alarm input types: NO/NC. When connect the ground port of the alarm device to the NVR, you can use any of the GND ports ( ). Connect the NC port of the alarm device to the alarm input port (ALARM) of the NVR. When there is peripheral power supplying for the alarm device, please make sure it is earthed with the NVR. 2.3.3 Alarm input and output port There is peripheral power supplying for the external alarm device.
Surge voltage Between touches with different polarity 1000VAC 1minute Between touch and winding 1000VAC 1minute Between touches with same polarity 1500V (10×160us) Length of open time 3ms max Length of close time 3ms max Longevity Mechanical 50×106 MIN (3Hz) Electrical 200×103 MIN (0.5Hz) Temperature -40 ~+70 2.4 Bidirectional talk 2.4.1 Device-end to PC-end Device Connection Please connect the speaker or the pickup to the first audio input port in the device rear panel.
Login the Web and then enable the corresponding channel real-time monitor. Please refer to the above interface (Figure 2-40) to enable bidirectional talk. Listening Operation At the PC-end, speak via the speaker or the pickup, and then you can get the audio from the earphone or sound box at the device-end. See Figure 2-42. Figure 2-42 2.5 Mouse Operation Please refer to the following sheet for mouse operation instruction.
In multiple-window mode, double left click one channel to view in full-window. Double left click current video again to go back to previous multiple-window mode. Right click mouse In real-time monitor mode, pops up shortcut menu. Press middle button In numeral input box: Exit current menu without saving the modification. Increase or decrease numeral value. Switch the items in the check box.
3 Device Installation Note: All the installation and operations here should conform to your local electric safety rules. 3.1 Check Unpacked NVR When you receive the NVR from the forwarding agent, please check whether there is any visible damage. The protective materials used for the package of the NVR can protect most accidental clashes during transportation. Then you can open the box to check the accessories. Please check the items in accordance with the list.
the proper position, the columns on the two sides can lock the screw holes of the HDD to secure it. When you remove the HDD, please refer to the following figure to pull the spring up and then remove the HDD. 3.3.2 NVR-401U/801U Series 1. Loosen the screws of the upper cover and side panel. 4. Turn the device upside down and then turn the screws in 2. Fix four screws in the HDD (Turn just three rounds). 5. Fix the HDD firmly. 3. Place the HDD in accordance with the four holes in the bottom. 6.
7. Put the cover in accordance 8. with the clip and then place the rear panel and the side panel. Secure the screws in the upper cover back. 3.3.3 NVR-1001U Series 1. Loosen the screws of the rear panel and side panel. 4. Turn the device upside down 2. Fix four screws in the HDD (Turn just three rounds). 5. Fix the HDD firmly. and then turn the screws in 3. Place the HDD in accordance with the four holes in the bottom. 6. Connect the HDD cable and power cable. firmly. 7.
3.
4 Local Basic Operation 4.1 Boot up and Shutdown 4.1.1 Boot up Before the boot up, please make sure: The rated input voltage matches the device power on-off button. Please make sure the power wire connection is OK. Then click the power on-off button. Always use the stable current, if necessary UPS is a best alternative measure. Please follow the steps listed below to boot up the device. Connect the device to the monitor and then connect a mouse. Connect power cable.
Figure 4-1 Click Cancel button or Next Step button, system goes to login interface. See Figure 4-2. System consists of four accounts: Username: admin. Password: admin. (administrator, local and network) Username: 888888. Password: 888888. (administrator, local only) Username: 666666. Password: 666666(Lower authority user who can only monitor, playback, backup and etc.) Username: default. Password: default (hidden user). Hidden user “default” is for system interior use only and can not be deleted.
Figure 4-3 Click Next button, you can go to network interface. See Figure 4-4 For detailed information, please refer to chapter 4.11. Figure 4-4 Click Next button, you can go to remote device interface. See Figure 4-5 For detailed information, please refer to chapter 4.4.
Figure 4-5 Click Next button, you can go to Schedule interface. See Figure 4-6. For detailed information, please refer to chapter 4.7.2. Figure 4-6 Click Finish button, system pops up a dialogue box. Click the OK button, the startup wizard is complete. See Figure 4-7.
Figure 4-7 4.3 Navigation Bar You need to go to the Main menu->Setting->System->General to enable navigation bar function; otherwise you can not see the following interface. The navigation bar is shown as below. See Figure 4-8. Figure 4-8 4.3.1 Main Menu Click button to go to the main menu interface. 4.3.2 Dual-screen operation Important This function is for some series only. Click to select screen 2, you can view an interface shown as below. See Figure 4-9. It is a navigation bar for screen 2.
Note Screen 2 funciton is null if tour is in process. Please disable tour funciton first, Right now, the screen 2 operation can only be realized on the navigation bard. The operations on the right-click menu are for screen 1 only. 4.3.3 Output Screen Select corresponding window-split mode and output channels. 4.3.4 Tour Click button to enable tour, the icon becomes , you can see the tour is in process. 4.3.5 PTZ Click , system goes to the PTZ control interface. Please refer to chapter 4.6.2. 4.
4.3.10 Remote Device Click , system goes to the remote device interface. Please refer to chapter 4.4 4.3.11 Network Click , system goes to the network interface. It is to set network IP address, default gateway and etc. Please refer to chapter 4.11. 4.3.12 HDD Manager Click system goes to the HDD manager interface. It is to view and manage HDD information. Please refer to chapter 4.12.1. 4.3.13 USB Manager Click system goes to the USB Manager interface.
Click Device search button, you can view the searched IP addresses at the top pane of the interface. Double click an IP address or check one IP address and then click Add button, you can add current device to the bottom pane of the interface. System supports batch add function. Click Manual Add button, you can add a device directly. Here you can set TCP/UPD/auto connection mode. The default setup is TCP. See Figure 4-13.
4.4.3 Image From main menu->setting->camera->image, you can see the image interface is shown as below. See Figure 4-15. Channel: Select a channel from the dropdown list. Saturation: It is to adjust monitor window saturation. The value ranges from 0 to 100. The default value is 50. The larger the number, the strong the color is. This value has no effect on the general brightness of the whole video. The video color may become too strong if the value is too high.
Day/night. It is to set device color and the B/W mode switch. The default setup is auto. Color: Device outputs the color video. Auto: Device auto select to output the color or the B/W video accord ing to the device feature (The general bright of the video or there is IR light or not.) B/W: The device outputs the black and white video. Sensor: It is to set when there is peripheral connected IR light. Please note some non-IR series product support sensor input function. Figure 4-15 4.4.
Figure 4-16 4.4.5 Upgrade It is to update the network camera. From main menu->setting->camera->remote, the interface is shown as below. See Figure 4-17. Click Browse button and then select the upgrade file. Then select a channel (or you can select device type filter to select several devices at the same time.) Click Begin button to upgrade. You can see the corresponding dialogue once the upgrade is finish.
4.4.6 Built-in Switch Setup The built-in switch function is for product of PoE port. From Main menu->Setting->Network->Switch, you can set switch IP address, subnet mask, gateway and etc. See Figure 4-19. Figure 4-19 4.5 Preview After device booted up, the system is in multiple-channel display mode. See Figure 4-20.Please note the displayed window amount may vary. The following figure is for reference only. Please refer to chapter 1.3 Specifications for the window-amount your product supported.
Figure 4-20 4.5.1 Preview If you want to change system date and time, you can refer to general settings (Main Menu>Setting->System->General). If you want to modify the channel name, please refer to the display settings (Main Menu->Camera->CAM name) Please refer to the following sheet for detailed information.
System may pop up a dialogue box if there is no such record in current channel. 2) Digital zoom It is to zoom in specified zone of current channel. It supports zoom in function of multiple -channel. Click as button , the button is shown . There are two ways for you to zoom in. Drag the mouse to select a zone, you can view an interface show as Figure 4-22.
channels become as . 6) Remote device Shortcut menu. Click it to go to the remote device interface to add/delete remote device or view its corresponding information. Please refer to chapter4.4.2 for detailed information. 4.5.3 Right Click Menu After you logged in the device, right click mouse, you can see the short cut menu. Please see Figure 4-24. Window split mode: You can select window amount and then select channels. PTZ: Click it to go to PTZ interface.
4.5.4.1 Video Color Here you can set hue, brightness, contrast, saturation, gain, white level, color mode and etc. See Figure 4-25. Figure 4-25 Please refer to the following sheet for detailed information. Item Note Period There are two periods in one day. You can set different sharpness, brightness, and contrast setup for different periods. Effective Time Check the box here to enable this function and then set period time. Sharpness Brightness The value here is to adjust the edge of the video.
Item Note lack brightness while the bright section may over exposure .The recommended value ranges from 40 to 60. Saturation It is to adjust monitor window saturation. The value ranges from 0 to 100. The default value is 50. The larger the number, the strong the color is. This value has no effect on the general brightness of the whole video. The video color may become too strong if the value is too high. For the grey part of the video, the distortion may occur if the white balance is not accurate.
Resolution: There are four options: 1280×1024 (Default), 1280×720, 1920×1080, 1024×768. Please note the system needs to reboot to activate current setup. VGA+HDMI2: It is for dual-screen operation. Please select from the dropdown list according to your actual situation. Click Apply button, system needs to restart to activate new setup. For example, 32+4 means for VGA, system max supports 32-window split and for HDMI2, system max supports 4-window split.
release button, you can change channel 1 and channel 16 position. Tour setup: Here you can set preview window channel display mode and interval. Please follow the steps listed below. From Main menu->Setting->System->Display->Tour, you can see an interface shown as in Figure 4-28. Here you can set tour parameter. Enable tour: Check the box here to enable tour function. Interval: Input proper interval value here. The value ranges from 1-120 seconds. Monitor tour type: System support 1/8-window tour.
Channel: Select the current camera channel. PTZ type: There are two types: local/remote. Please select local mode if you are connect RS485 cable to connect to the Speed dome (PTZ). Please select remote mode if yo u are connecting to the network PTZ camera. Protocol: Select corresponding PTZ protocol(such as PELCOD) Address: Default address is 1. Baud rate: Select corresponding baud rate. Default value is 9600. Data bit: Select corresponding data bits. Default value is 8.
Figure 4-30 4.6.2 PTZ Control After completing all the setting please click save button. Right click mouse (click “Fn” Button in the front panel or click “Fn” key in the remote control). The interface is shown as in Figure 4-31. Please note you can only go to the PTZ control interface when you are in 1 -window display mode. Figure 4-31 The PTZ setup is shown as in See Figure 4-32. Please note the commend name is grey once device does not support this function.
The PTZ operation is only valid in one-window mode. Here you can control PTZ direction, speed, zoom, focus, iris, preset, tour, scan, pattern aux function, light and wiper, rotation and etc. Speed is to control PTZ movement speed. The value ranges from 1 to 8.The speed 8 is faster than speed 1. You can use the remote control to click the small keyboard to set. You can click and of the zoom, focus and iris to zoom in/out, definition and brightness. The PTZ rotation supports 8 directions.
Figure 4-34 Please refer to the following sheet for detailed information. Please note the above interface may vary due to different protocols. The button is grey and can not be selected once the current function is null. Right click mouse or click the ESC button at the front panel to go back to the Figure 4-32. Icon Function Icon Function Preset Flip Tour Reset Pattern Aux Scan Aux on-off button Rotate Go to menu 4.6.2.
The interface is shown as in Figure 4-36. Click Set button and then input preset number. Click Set button to save current preset. Figure 4-36 Tour Setup In Figure 4-35, click tour button. Input tour value and preset No. Click Add preset button to add current preset to the tour. See Figure 4-37. Tips Repeat the above steps to add more presets to the tour. Click Del preset button to remove it from the tour. Please note some protocols do not support delete preset function.
Figure 4-38 Scan Setup In Figure 4-35, click Scan button. Use direction buttons to set camera left limit and then click Left button. Use direction buttons to set camera right limit and then click Right button. Now the scan setup process is complete. Figure 4-39 4.6.2.2 Call PTZ Function Call Preset In Figure 4-34, input preset value and then click to call a preset. Click again to stop call. Call Pattern In Figure 4-34, input pattern value and then click call. to call a pattern.
Call Scan In Figure 4-34, input Scan value and then click to call a tour. Click again to stop call. Rotate In Figure 4-34, click to enable the camera to rotate. System supports preset, tour, pattern, scan, rotate, light and etc function. Note: Preset, tour and pattern all need the value to be the control parameters. You can define it as y ou require. You need to refer to your camera user’s manual for Aux definition. In some cases, it can be used for special process.
Quality: There are six levels ranging from 1 to 6. The sixth level has the highest image quality. Video/audio: You can enable or disable the video/audio. Please note, once you enable audio function for one channel, system may enable audio func tion of the rest channels by default. Copy After you complete the setup, you can click Copy button to copy current setup to other channel(s). You can see an interface is shown as in Figure 4-44. You can see current channel number is grey.
Figure 4-42 4.7.1.3 Snapshot Here you can set snapshot mode, picture size, quality and frequency. See Figure 4-43. Snapshot mode: There are two modes: regular and trigger. If you set regular mode, you need to set snapshot frequency. If you set trigger snapshot, you need to set snapshot activation operation. Image size: Here you can set snapshot picture size. Image quality: Here you can set snapshot quality. The value ranges from 1 to 6.
Figure 4-43 Figure 4-44 4.7.2 Schedule The record type priority is: Alarm>Motion detect>Regular. 4.7.2.1 Schedule Record Set record time, record plan and etc. Please note system is in 24-hour record by default after its first boot up. In the main menu, from Main menu->Setting->Storage->Schedule, you can go to schedule menu. See Figure 4-48. There are total six periods.
Channel: Please select the channel number first. You can select “all” if you want to set for the whole channels. : Sync connection icon. Select icon together. Now the icon is shown as of several dates, all checked items can be edited or . : Click it to delete a record type from one period. Record Type: Please check the box to select corresponding record type. There are four types: Regular/MD (motion detect)/Alarm/MD&Alarm.
Figure 4-47 Please check the box to select the corresponding function. After completing all the setups ple ase click save button, system goes back to the previous menu. There are color bars for your reference. Green color stands for regular recording, yellow color stands for motion detection and red color stands for alarm recording. The white means the MD and alarm record is valid.
Figure 4-49 Quick Setup Copy function allows you to copy one channel setup to another. After setting in channel 1, click Copy button, you can go to interface Figure 4-50. You can see current channel name is grey such as channel 1. Now you can select the channel you wan to paste such as channel 5/6/7. If you wan to save current setup of channel 1 to all channels, you can click the first box “ALL”. Click the OK button to save current copy setup.
Figure 4-51 From Main menu->Setting->Camera->Encode->Snapshot, you can go to snapshot interface. See Figure 4-52. Select the snapshot channel from the dropdown list and then select snapshot mode as Timing (Schedule) from the dropdown list and then set picture size, quality and snapshot frequency.
In the main menu, from Main menu->Setting->Storage->Schedule, you can go to schedule menu. See Figure 4-48. Here you can set snapshot period. There are total six periods in one day. Please refer to chapter 4.7.2.1 for detailed setup information. The setup steps are general the same. Figure 4-53 Note Please note the trigger snapshot has the higher priority than regular snapshot.
b) c) d) Figure 4-54 Select motion detect from the event type dropdown list. Select a channel from the dropdown list and then check the enable button to enable motion detect function. Click Region Select button to set motion detect zone. There are 396(PAL)/330(NTSC) small zones. The green zone is current cursor position. Grey zone is the motion detection zone. Black zone is the disarmed zone. You can click Fn button to switch between the arm mode and disarm mode.
i) j) Click Copy button to copy current setup to other channel(s). Click OK button to complete motion detect record setup. Figure 4-55 Figure 4-56 4.7.3.2 Motion Detect Snapshot a) b) c) d) From Main menu->Setting->Camera->Encode->Snapshot, you can go to snapshot interface. See Figure 4-57. In Figure 4-57, select trigger snapshot from the dropdown list and then set picture size, quality and snapshot frequency. Click OK button to save current setup.
Figure 4-57 4.7.4 Alarm Record/Snapshot 4.7.4.1 Alarm Record a) Before you set alarm setup information, please go to chapter 2.3 to connect alarm input and alarm output cable (such as light, siren and etc). b) The record priority is: Alarm>Motion detect>Regular. In the main menu, from Setting->Event-> Alarm, you can see alarm setup interface. See Figure 4-58. Alarm in: Here is for you to select channel number. Event type: There are four types. Local input/network input/IPC external/IPC offline alarm.
Figure 4-58 d) e) f) g) From Mani menu->Setting->Storage->Schedule, you can go to Figure 4-48. Select alarm channel, period and the record type shall be alarm. Please refer to chapter 4.7.2. Click Copy button to copy current setup to other channel(s). Click OK button to save alarm record information. 4.7.4.2 Alarm Snapshot a) b) c) d) Please refer to Step a) to step c) of chapter 4.7.3.2 to enable timing snapshot.
Figure 4-59 4.7.5 Manual Record/Snapshot You need to have proper rights to implement the following operations. Please make sure the HDD has been properly installed. 4.7.5.1 Manual Record a) Right click mouse and select manual record or in the main menu, Setting->Storage->Manual Record. Manual record menu is show n as in Figure 4-60. from Tips You can click Rec button on the front panel (if possible) to go to the Manual Record interface.
Figure 4-60 b) Check the box here to select manual record channel(s). You can see the corresponding indicator light on the front panel is on. Channel: It is to display device all channels. Manual: It has the highest priority. Enable corresponding channel to record no matter what period applied in the record setup. Now system is record general file. Auto: System enables auto record function as you set in chapter 4.7.
4-61. Figure 4-61 b) Click Add new holiday button, you can see an interface shown as in Figure 4-62. Here you can set holiday date name, repeat mode, start time/end time and etc.
c) d) Click Add button to complete holiday setup. Now you can enable holiday setup and then click Apply button. From Main menu->setting->Storage->schedule, you can go to schedule interface. See Figure 4-63. Now you can set period and record type of holiday time. Please refer to chapter 4.7.2.1 for detailed setup information. Figure 4-63 e) Click OK button to set holiday record setup. 4.7.6.2 Holiday Snapshot Set Holiday date first. Please refer to step a) to step c) of chapter 4.7.6.1.
4.8.2 Search Interface From Main menu->Search, or on the preview interface right click mouse and then select search item, you can go to the following interface. See Figure 4-64. Figure 4-64 Please refer to the following sheet for more information. SN 1 Name Display window Function Here is to display the searched picture or file. Support 1/4/9/16-window playback. Search type Here you can select to search the picture or the recorded file.
mode and channel selection pane. 5 Card number search 6 Mark file list button In 1-window playback mode: you can select 1-X channels (X depends on the product channel amount). In 4-window playback mode: you can select 4 channels according to your requirement. In 9-window playback mode, you can switch between 1-8, 9-16 and etc channels. In 16-window playback mode, you can switch between1-16, 17-32 and etc channels.
In normal play mode, when you pause current play, you can click │ and │ to begin frame by frame playback. In frame by frame playback mode, click ►/to restore normal playback. ► Slow play In playback mode, click it to realize various slow play modes such as slow play 1, slow play 2, and etc. Fast forward In playback mode, click to realize various fast play modes such as fast play 1,fast play 2 and etc. Note: The actual play speed has relationship with the software version.
display 32 files from one channel. After you clip on record file, click Backup button you can save it. For one device, if there is a backup in process, you can not start a new backup operation. 12 Clip It is to edit the file. ●Please play the file you want to edit and then click this button when you want to edit. You can see the corresponding slide bars in the time bar of the corresponding channel. You can adjust the slide bar or input the accurate time to set the file end time.
channel when playback This function is null if there is no record file or system is in smart search process. Note: All the operations here (such as playback speed, channel, time and progress) have relationship with hardware version. Some series NVRs do not support some functions or playback speeds. 4.8.2.1 Smart Search During the multiple-channel playback mode, double click one channel and then click the button, system begins smart search. System supports 396(22*18 PAL) and 330(22*15 NTSC) zones.
After you searched files, system implement accurate playback once you click Play for the first time. System does not support accurate playback for picture. System supports synchronization playback and non-synchronous playback. The synchronization playback supports all channels and non-synchronous playback only supports accurately playback of current select channel. Figure 4-66 4.8.2.3 Mark Playback Please make sure your purchased device support this function.
Mark Manager Click the mark manager button on the Search interface (Figure 4-64); you can go to Mark Manager interface. See Figure 4-68. System can manage all the record mark information of current channel by default. You can view all mark information of current channel by time. Figure 4-68 Modify Double click one mark information item, you can see system pops up a dialogue box for you to change mark information. You can only change mark name here.
Figure 4-69 c) Select backup device and then set channel, file start time and end time. d) Click add button, system begins search. All matched files are listed below. System automatically calculates the capacity needed and remained. See Figure 4-70. e) System only backup files with a √ before channel name. You can use Fn or cancel button to delete √ after file serial number. f) Click backup button, you can backup selected files. There is a process bar for you reference.
h) Click backup button, system begins burning. At the same time, the backup button becomes stop button. You can view the remaining time and process bar at the left bottom. Note During backup process, you can click ESC to exit current interface for other operation (For some series product only). The system will not terminate backup process. The file name format usually is: Channel number+Record type+Time. In the file name, the YDM format is Y+M+D+H+M+S. File extension name is .dav. 4.9.
Format: Click Format button, system pops up a dialogue box for you to confirm current operation. System begins format process after you click the OK button. Note: System can not open config backup interface again if there is backup operation in the process. System refreshes device when you go to the config backup every time and set current directory as the root directory of the peripheral device.
Figure 4-73 4.10 Alarm 4.10.1 Detect Alarm In the main menu, from Setting to Detect, you can see motion detect interface. See Figure 4-74.There are three detection types: motion detection, video loss, tampering. 4.10.1.1 Motion Detect After analysis video, system can generate a motion detect alarm when the detected moving signal reached the sensitivity you set here. Detection menu is shown as below. See Figure 4-74. Event type: From the dropdown list you can select motion detection type.
screen prompt, alarm upload, email will not be activated again. After 10s, if system detects another alarm signal, it can generate an alarm since the anti -dither time is out. Period: Click set button, you can see an interface is shown as in Figure 4-77. Here you can set motion detect period. System only enables motion detect operation in the specified periods. It is not for video loss or the tampering. There are two ways for you to set periods. Please note system only supports 6 periods in one day.
Figure 4-74 Figure 4-75 147
Figure 4-76 Figure 4-77 148
Figure 4-78 Motion detect here only has relationship with the sensitivity and region setup. It has no relationship with other setups. 4.10.1.2 Tampering When someone viciously masks the lens, or the output video is in one -color due to the environments light change, the system can alert you to guarantee video continuity. Tampering interface is shown as in Figure 4-79. You can enable “Alarm output “or “Show message” function when tampering alarm occurs. Sensitivity: The value ranges from 1 to 6.
Figure 4-79 4.10.1.3 Video Loss In Figure 4-74, select video loss from the type list. You can see the interface is shown as in Figure 4-80. This function allows you to be informed when video loss phenomenon occurred. You can enable alarm output channel and then enable show message function. You can refer to chapter 4.10.1.1Motion detect for detailed information. Tips: You can enable preset/tour/pattern activation operation when video loss occu rs.
Figure 4-80 4.10.2 Alarm output From Main menu->Setting->Event->Alarm output, you can see an interface shown as in Figure 4-81. Here is for you to set proper alarm output (Auto/manual/stop). Click OK button of the alarm reset, you can clear all alarm output status.
Please highlight icon to select the corresponding alarm output. After all the setups please click OK button, system goes back to the previous menu. 4.10.3 Alarm Setup In the main menu, from Setting->Event->Alarm, you can see alarm setup interface. Alarm in: Here is for you to select channel number. In the main menu, from Setting->Event->Alarm, you can see alarm setup interface. See Figure 4-82. There are four alarm types. See Figure 4-82 to Figure 4-85.
Alarm output: The number here is the device alarm output port. You can select the corresponding ports(s) so that system can activate the corresponding alarm device(s) when an alarm occurred. Latch: When the anti-dither time ended, the channel alarm you select in the alarm output may last the specified period. The value ranges from 1 to 300 seconds. This function is not for other alarm activation operations. The latch is still valid even you disable the alarm event function directly.
Figure 4-82 Figure 4-83 154
. Figure 4-84 Figure 4-85 155
Figure 4-86 Figure 4-87 156
Figure 4-88 Please highlight icon to select the corresponding function. After setting all the setups please click save button, system goes back to the previous menu. 4.10.4 Abnormality There are two types: Disk/Network. Disk: Disk error, no disk, no space. See Figure 4-89 and Figure 4-90. Network: Disconnection, IP conflict, MAC conflict. See Figure 4-91. Alarm output: Please select alarm activation output port (multiple choices).
Figure 4-89 Figure 4-90 158
Figure 4-91 4.11 Network 4.11.1 Basic Setup The single network adapter interface is shown as in Figure 4-92 and the dual network adapters interface is shown as in Figure 4-93. Network Mode : Includes multiple access, fault tolerance, and load balancing Multiple-address mode: eth0 and eth1 operate separately. You can use the services such as HTTP, RTP service via etho0 or the eth1.
IP Version: There are two options: IPv4 and IPv6. Right now, system supports these two IP address format and you can access via them. MAC address: The host in the LAN can get a unique MAC address. It is for you to access in the LAN. It is read-only. IP address: Here you can use up/down button () or input the corresponding number to input IP address. Then you can set the corresponding subnet mask the default gateway. Default gateway: Here you can input the default gateway.
Figure 4-92 Figure 4-93 4.11.1.1 Connection The connection setup interface is shown as in Figure 4-94.
Max connection: system support maximal 128 users. 0 means there is no connection limit. TCP port: Default value is 37777. UDP port: Default value is 37778. HTTP port: Default value is 80. HTTPS port: Default value is 443. RTSP port: Default value is 554. Important: System needs to reboot after you changed and saved any setup of the above four ports. Please make sure the port values here do not conflict. Figure 4-94 4.11.1.2 WIFI The WIFI interface is shown as below. See Figure 4-95.
Figure 4-95 WIFI working status: Here you can view current connection status. Please note: After successful connection, you can see WIFI connection icon at the top right corner of the preview interface. When the hotspot verification type is WEP, system displays as AUTO since the device can not detect its encryption type. System does not support verification type WPA and WPA2. The display may become abnormal for the verification type and encryption type.
APN: It is the wireless connection server. It is to set you access the wireless network via which method. AUTH: It is the authentication mode. It supports PAP/CHAP. Dial number: Please input 3G network dialup number you got from your ISP. User name: It is the user name for you to login the 3G network. Password: It is the password for you to login the 3G network. Pulse interval: You can set dialup duration. Once you disable the extra stream, the connection time begins.
Figure 4-97 4.11.1.5 DDNS Setup DDNS setup interface is shown as in Figure 4-98. You need a PC of fixed IP in the internet and there is the DDNS softw are running in this PC. In other words, this PC is a DNS (domain name server). In network DDNS, please select DDNS type and highlight enable item. And them please input your PPPoE name you get from you IPS and server IP (PC with DDNS). Click save button and then reboot system. Click save button, system prompts for rebooting to get all setup activated.
Figure 4-98 Please note NNDS type includes: CN99 DDNS, NO-IP DDNS, Quick DDNS, Dyndns DDNS and sysdns DDNS. All the DDNS can be valid at the same time, you can select as you requirement. Private DDNS function shall work with special DDNS server and special Professional Surveillance Software (PSS). Quick DDNS and Client-end Introduction 1) Background Introduction Device IP is not fixed if you use ADSL to login the network. The DDNS function allows you to access the NVR via the registered domain name.
the device IP. User name: It is optional. You can input your commonly used email address. Important Do not register frequently. The interval between two registrations shall be more than 60 seconds. Too many registration requests may result in server attack. System may take back the domain name that is idle for one year. You can get a notification email before the cancel operation if your email address setup is OK. 4.11.1.
Figure 4-99 Figure 4-100 4.11.1.7 IP Filter IP filter interface is shown as in Figure 4-101. You can add IP in the following list. The list supports max 64 IP addresses. System supports valid address of IPv4 and IPv6. Please note system needs to check the validity of all IPv6 addresses and implement optimization. After you enabled trusted sites function, only the IP listed below can access current NVR. If you enable blocked sites function, the following listed IP addresses can not access current NVR.
Type: You can select trusted site and blacklist from the dropdown list. You can view the IP address on the following column. Start address/end address: Select one type from the dropdown list, you can input IP address in the start address and end address. Now you can click Add IP address or Add IP section to add. a) For the newly added IP address, it is in enable status by default. Remove the √ before the item, and then current item is not in the list. b) System max supports 64 items.
Figure 4-102 4.11.1.8 Email The email interface is shown as below. See Figure 4-103. SMTP server: Please input your email SMTP server IP here. Port: Please input corresponding port value here. User name: Please input the user name to login the sender email box. Password: Please input the corresponding password here. Sender: Please input sender email box here. Title: Please input email subject here. System support English character and Arabic number. Max 32-digit.
Figure 4-103 4.11.1.9 FTP You need to download or buy FTP service tool (such as Ser-U FTP SERVER) to establish FTP service. Please install Ser-U FTP SERVER first. From “start” -> “program” -> Serv-U FTP Server -> Serv-U Administator. Now you can set user password and FTP folder. Please note you need to grant write right to FTP upload user. See Figure 4-104. Figure 4-104 You can use a PC or FTP login tool to test setup is right or not. For example, you can login user ZHY to FTP://10.10.7.
Figure 4-105 System also supports upload multiple NVRs to one FTP server. You can create multiple folders under this FTP. FTP interface is shown as in Figure 4-106. Please highlight the icon in front of Enable to activate FTP function. Here you can input FTP server address, port and remote directory. When remote directory is null, system automatically create folders according to the IP, time and channel. User name and password is the account information for you to login the FTP.
4.11.1.10 SNMP SNMP is an abbreviation of Simple Network Management Protocol. It provides the basic network management frame of the network management system. The SNMP widely used in many environments. It is used in many network device, software and system. You can set in the following interface. See Figure 4-107. Figure 4-107 Please enable the SNMP function. Use the corresponding software tool (MIB Builder and MG-SOFT MIB Browser.
Figure 4-108 Here you can set a multiple cast group. Please refer to the following sheet for detailed information. IP multiple cast group address -224.0.0.0-239.255.255.255 -“D”addressspace The higher four-bitofthefirstbyte=”1110” Reserved local multiple cast group address -224.0.0.0-224.0.0.255 -TTL=1 When sending out telegraph -For example 224.1.1.1 All systems in the sub-net 224.1.1.2 All routers in the sub-net 224.1.1.4 DVMRP router 224.1.1.5 OSPF router 224.0.0.
Please note multiple cast function applies to special series only. 4.11.1.12 Alarm Centre This interface is reserved for you to develop. See Figure 4-109. Figure 4-109 4.11.1.13 Auto register This function allows the device to auto register to the proxy you specified. In this way, you can use the client-end to access the NVR and etc via the proxy. Here the proxy has a switch function. In the network service, device supports the server address of IPv4 or domain.
Figure 4-110 2) The proxy server software developed from the SDK. Please open the software and input the global setup. Please make sure the auto connection port here is the same as the port you set in the previous step. 3) Now you can add device. Please do not input default port number such as the TCP port in the mapping port number. The device ID here shall be the same with the ID you input in Figure 4-110. Click Add button to complete the setup. 4) Now you can boot up the proxy server.
Figure 4-111 4.11.1.15 P2P The P2P interface is shown as in Figure 4-112. You can visit www.easy4ip.com to scan the QR code to login. Figure 4-112 4.11.2 Network Test In this interface, you can see network test and network load information. 4.11.2.1 Network Test From main menu->Info-Network->Test, the network test interface is shown as in Figure 4-113. Destination IP: Please input valid IPV4 address and domain name.
Test: Click it to test the connection with the destination IP address. The test results can display average delay and packet loss rate and you can also view the network status as OK, bad, no connection and etc. Network Sniffer backup: Please insert USB2.0 device and click the Refresh button, you can view the device on the following column. You can use the dropdown list to select peripheral device. Click Browse button to select the snap path. The steps here are same as preview backup operation.
Figure 4-114 4.12 HDD Setup Here you can view HDD information such as type, status, total capacity, record time and etc. The operation includes format, resume from error, change HDD property (Read write, Read-only). Here you can also set alarm and HDD storage position. 4.12.1 Format a) From Mani-menu->Setting->Storage->HDD Manager, you can go to HDD management interface. See Figure 4-115.
Figure 4-115 b) Select a HDD and then select format from the dropdown list. Click Execute button. c) Click OK button to complete the setup. You can see system needs to restart to activate current setup. 4.12.2 HDD Information Here is to list hard disk type, total space, free space, and status. See Figure 4-116. ○ means current HDD is normal.. - means there is no HDD. If disk is damaged, system shows as “?”. Please remove the broken hard disk before you add a new one.
Figure 4-116 In Figure 4-116, click one HDD item, the S.M.A.R.T interface is shown as in Figure 4-117.
Parameter Function SATA 1 here means there is 1 HDD. For different series product, the max HDD amount may vary, When HDD is working properly, system is shown as O. . “_” means there is no HDD. SN You can view the HDD amount the device connected to; means the second HDD is current working HDD. Type The corresponding HDD property. Total space The HDD total capacity. Free space The HDD free capacity. Status HDD can work properly or not. Bad track Display there is bad track or not.
Figure 4-118 Please select the correspond group from the dropdown list and then click Apply button. Click main stream/sub stream/snapshot button to set corresponding HDD group information. See Figure 4-119 through Figure 4-121.
Figure 4-120 Figure 4-121 4.12.4 RAID Manager Important Please make sure your purchased product support the RAID function, otherwise you can not see the following interface. Right now, RAID supports Raid0, Raid1, Raid5, Raid6, and Raid10.
Raid5, Raid6, and Raid10. 4.12.4.1 RAID Config It is for you to manage RAID HDD. It can display RAID name, type, free space, total space, status and etc. Here you can add/delete RAID HDD. Click Add button to select RAID type and then select HDDs, click OK button to add. See Figure 4-122. Figure 4-122 4.12.4.2 Hotspare disks Click Hotspare disks tab name, you can add the hot spare HDD. See Figure 4-123. The type includes two options: Global: It is global hotspare disk.
Figure 4-123 4.13 Basic Setups Set NVR basic setup, device setup and other setups. 4.13.1 Device Setup From Main menu->Setting->System->General, you can go to the general interface. See Figure 4-125. Pack duration: Here is for you to specify record duration. The value ranges from 0 to 120 minutes. Default value is 60 minutes. Device ID: Please input a corresponding device name here.
IPC Time Sync: You can input an interval here to synchronize the NVR time and IPC time. Startup wizard: Once you check the box here, system will go to the startup wizard directly when the system restarts the next time. Otherwise, it will go to the logi n interface. Mouse property: You can set double click speed via dragging the slide bard. You can Click Default button to restore default setup. Figure 4-124 4.13.
Figure 4-125 4.13.3 Holiday Holiday setup interface is shown as in Figure 4-126. Click Add new holiday button, you can input new holiday information. See Figure 4-127. Here you can set holiday name, repeat mode and start/end time.
Figure 4-127 4.14 Device Maintenance and Manager 4.14.1 System Info 4.14.1.1 Version From main menu->Info->System->version, you can go to version interface. Here is for you to view some version information. See Figure 4-128. Please note the following figure for reference only.
Figure 4-128 4.14.1.2 BPS Here is for you to view current video bit rate (kb/s) and resolution. See Figure 4-129. Figure 4-129 4.14.1.3 Online User Here is for you manage online users connected to your NVR. See Figure 4-130.
You can click button to disconnect or block one user if you have proper system right. System detects there is any newly added or deleted user in each five seconds and refresh the list automatically. Figure 4-130 4.14.1.4 Remote Device Information From main menu->info-Event, here you can view the channel status of the remote device, connection log and etc. See Figure 4-131.
Figure 4-131 4.14.1.5 Remote 4.14.1.5.1 Device Status Here you can view the IPC status of the corresponding channel such as motion detect, video loss, tampering, alarm and etc. See Figure 4-132. IPC status: : Front-end does not support. event from current front-end. Connection Refresh: Click it to get latest front-end channel status. status: : Front-end supports. : Connection succeeded. : There is alarm : Connection failed.
Figure 4-132 4.14.1.5.2 Firmware It is to view channel, IP address, manufacturer, type, system version, SN, video input, audio input, external alarm and etc. See Figure 4-133.
4.14.2 Log From Main menu->Info->Log, you can go to the following interface. See Figure 4-134. Start time/end time: Pleased select start time and end time, then click search button. You can view the log files in a list. System max displays 100 logs in one page. It can max save 1024 log files. Please use page up/down button on the interface or the front panel to view more. Tips Double click a log item to view its detailed information. See Figure 4-135. Click PgUp/PgDn to view more logs.
Figure 4-135 4.14.3 Account Here is for you to implement account management. See Figure 4-136 and Figure 4-137. Here you can: Add new user Modify user Add group Modify group Modify password. For account management please note: For the user account name and the user group, the string max length is 6-byte. The backspace in front of or at the back of the string is invalid. There can be backspace in the middle.
Figure 4-136 Figure 4-137 4.14.3.
Click add group button, the interface is shown as below. See Figure 4-138. Here you can input group name and then input some memo information if necessary. There are many rights such as control panel, shut down, real-time monitor, playback, record, record file backup, PTZ, user account, system information view, alarm input/output setup, system setup, log view, clear log, upgrade system, control device and etc. The modify group interface is similar to the Figure 4-138. Figure 4-138 4.14.3.
Figure 4-139 4.14.4 Update From Mani menu->Setting->Info->Update, you can go to the following interface. See Figure 4-140. a) Insert USB device that contain the upgrade file. b) Click Start button and then select the .bin file. c) You can see the corresponding dialogue box after the update process is complete.
4.14.5 Default You can restore factory default setup to fix some problems when the device is running slowly. Configuration error occurred. From Main menu->Setting->System->Default, you can go to the default interface. See Figure 4-141. Click default icon, system pops up a dialogue box. You can highlight to restore factory default setup. All Camera Network Event Storage System Please highlight icon to select the corresponding function.
Function: There are various devices for you to select. Console is for you to use the COM or mini -end software to upgrade or debug the program. The control keyboard is for you to control the device via the special keyboard. Transparent COM (adapter) is to connect to the PC to transfer data directly. Protocol COM is for card overlay function. Network keyboard is for you to use the special keyboard to control the device. PTZ matrix is to connect to the peripheral matrix control.
Figure 4-143 4.14.8 Logout /Shutdown/Restart From Mani menu->Operation->Shutdown, you can see an interface shown as in Figure 4-144. Shutdown: System shuts down and turns off power. Logout: Log out menu. You need to input password when you login the next time. Restart: reboot device. If you shut down the device, there is a process bar for your reference, system waits for 3 seconds and then shut down (You can not cancel).
5 Web Operation 5.1 General Introduction The device web provides channel monitor menu tree, search, alarm setup, system setup, PTZ control and monitor window and etc. Important The following operation is based on 32-channel series device. 5.1.1 Preparation Before log in, please make sure: Network connection is right NVR and PC network setup is right. Please refer to network setup(main menu->setting->network) Use order ping ***.***.***.***(* NVR IP address) to check connection is OK or not.
Figure 5-2 After installation, the interface is shown as below. See Figure 5-3. Figure 5-3 Please input your user name and password. Default factory name is admin and password is admin. Note: For security reasons, please modify your password after you first login. 5.2 LAN Mode For the LAN mode, after you logged in, you can see the main window. See Figure 5-9. This main window can be divided into the following sections.
Section 1: there are six function buttons: Live chapter 0 , setup (chapter 5.8), info (Chapter 5.9), playback (chapter 5.10), alarm (chapter 5.11), and logout (chapter 5.12). Section 2: There are monitor channels successfully connected to the NVR. Please refer to Figure 5-4 for main stream and extra stream switch information. Figure 5-4 Section 3: Open all. Open all button is to enable/disable all-channel real-time monitor. Here you can select main stream/sub stream too. See Figure 5-5.
The Web can playback the saved (Extension name is dav) files in the PC-end. Click local play button, system pops up the following interface for you to select local play file. See Figure 5-8. Figure 5-8 Section 7 Zero-channel encoding. Please refer to chapter 5.6 for detailed information. Section 8: PTZ operation panel. Please refer to chapter 5.4 for detailed information. Section 9: Image setup and alarm setup. Please refer to chapter 5.5 for detailed information.
In section 2, left click the channel name you want to view, you can see the corresponding video in current window. On the top left corner, you can view device IP(172.11.10.11), channel number(1), network monitor bit stream(2202Kbps) and stream type(M=main stream, S=sub stream). See Figure 5-10. 1 2 3 4 Figure 5-10 On the top right corner, there are six unction buttons. See Figure 5-11.
Parameter Function Preset Select Preset from the dropdown list. Turn the camera to the corresponding position and Input the preset value. Click Add button to add a preset. Tour Select Tour from the dropdown list. Input preset value in the column. Click Add preset button, you have added one preset in the tour. Repeat the above procedures you can add more presets in one tour. Or you can click delete preset button to remove one preset from the tour.
5.5 Image/Alarm-out Select one monitor channel video and then click Image button in section 9, the interface is shown as Figure 5-13. 5.5.1 Image Here you can adjust its brightness, contrast, hue and saturation. (Current channel border becomes green). Or you can click Reset button to restore system default setup. Figure 5-13 5.5.2 Alarm output Here you can enable or disable the alarm signal of the corresponding port. See Figure 5-14. Figure 5-14 5.
Figure 5-15 5.7 WAN Login In WAN mode, after you logged in, the interface is shown as below. See Figure 5-16. Figure 5-16 Please refer to the following contents for LAN and WAN login difference. 1) In the WAN mode, system opens the main stream of the first channel to monitor by default. The open/close button on the left pane is null. 2) You can select different channels and different monitor modes at the bottom of the interface.
Figure 5-17. Figure 5-17 Important The window display mode and the channel number are by default. For example, for the 16-channel, the max window split mode is 16. 3) Multiple-channel monitor, system adopts extra stream to monitor by default. Double click one channel, system switches to single channel and system uses main stream to monitor. You can view there are two icons at the left top corner of the channel number for you reference. M stands for main stream. S stands for sub stream (extra stream).
Figure 5-18 Figure 5-19 Please refer to the following sheet for log parameter information. Parameter Function Device search Click Device search button, you can view the searched device information on the list. It includes device IP address, port, device name, manufacturer and type. Add Select a device in the list and then click Add button, system can connect the device automatically and add it to the Added device list. Or you can double click one item in the list to add a device.
Parameter Modify Function Click or any device in the Added device list, you can change the corresponding channel setup. Delete Click , you can delete the remote connection of the corresponding channel. Connection status : Connection succeeded. : Connection failed. Delete Select a device in the Added device list and then click Delete button, system can disconnect the device and remove it from the Added device list. Manual Add Click it, the interface is shown as in Figure 5-19.
Please refer to the following sheet for detailed information. Parameter Function Channel Please select a channel from the dropdown list. Period It divides one day (24 hours) to two periods. You can set different hue, brightness, and contrast for different periods. Hue It is to adjust monitor video brightness and darkness level. The default value is 50. The bigger the value is, the large the contrast between the bright and dark section is and vice versa.
BLC Mode BLC The device auto exposures according to the environments situation so that the darkest area of the video is cleared WDR For the WDR scene, this function can lower the high bright section and enhance the brightness of the low bright section. So that you can view these two sections clearly at the same time. The value ranges from 1 to 100. When you switch the camera from no-WDR mode to the WDR mode, system may lose several seconds record video.
Figure 5-21 Please refer to the following sheet for detailed information. Parameter Function Channel Please select a channel from the dropdown list. Video enable Check the box here to enable extra stream video. This item is enabled by default. Code stream type It includes main stream, motion stream and alarm stream. You can select different encode frame rates form different recorded events. System supports active control frame function (ACF). It allows you to record in different frame rates.
VBR mode. Reference bit rate Recommended bit rate value according to the resolution and frame rate you have set. I Frame Here you can set the P frame amount between two I frames. The value ranges from 1 to 150. Default value is 50. Recommended value is frame rate *2. Watermark enable This function allows you to verify the video is tampered or not. Here you can select watermark bit stream, watermark mode and watermark character. Default character is DigitalCCTV. The max length is 85-digit.
5.8.1.3.3Video Overlay The video overlay interface is shown as in Figure 5-23. Figure 5-23 Please refer to the following sheet for detailed information. Parameter Function Cover-area Check Preview or Monitor first. Click Set button, you can privacy mask the specified video in the preview or monitor video. System max supports 4 privacy mask zones. You can enable this function so that system overlays time information in video window. You can use the mouse to drag the time title position.
Figure 5-24 5.8.1.4 Channel Name Here you can set channel name. See Figure 5-25. Figure 5-25 5.8.1.5 IPC Upgrade This interface is to upgrade network camera. See Figure 5-26. Click Browse button to select upgrade file. Or you can use filter to select several network cameras at the same time.
Figure 5-26 5.8.2 Network 5.8.2.1 TCP/IP The TCP/IP interface is shown as in Figure 5-27. Figure 5-27 Please refer to the following sheet for detailed information. Parameter Function Mode There are two modes: static mode and the DHCP mode. The IP/submask/gateway are null when you select the DHCP mode to auto search the IP.
IP/submask/gateway manually. If you select the DHCP mode, you can view the IP/submask/gateway from the DHCP. If you switch from the DHCP mode to the static mode, you need to reset the IP parameters. Besides, IP/submask/gateway and DHCP are read-only when the PPPoE dial is OK. Mac Address It is to display host Mac address. IP Version It is to select IP version. IPV4 or IPV6. You can access the IP address of these two versions.
Figure 5-29 Please refer to the following sheet for detailed information. Parameter Function Max connection It is the max Web connection for the same device. The value ranges from 1 to 120. The default setup is 120. TCP port The default value is 37777. You can input the actual port number if necessary. UDP port The default value is 37778. You can input the actual port number if necessary. HTTP port The default value is 80. You can input the actual port number if necessary.
Figure 5-30 Please check the box to enable WIFI function and then click the Search SSID button. Now you can view all the wireless network information in the following list. Double click a name to connect to it. Click Refresh button, you can view latest connection status. 5.8.2.5 3G 5.8.2.5.1CDMA/GPRS The CDMA/GPRS interface is shown as in Figure 5-31.
Please refer to the following sheet for detailed information. Parameter Function WLAN type Here you can select 3G network type to distinguish the 3G module from different ISP. The types include WCDMA CDMA1x and etc. APN/Dial No. Here is the important parameter of PPP. Authorization It includes PAP,CHAP,NO_AUTH. Pulse interval It is to set time to end 3G connection after you close extra stream monitor.
Device connects to the internet via PPPoE after reboot. You can get the IP address in the WAN from the IP address column. Please note, you need to use previous IP address in the LAN to login the device. Please go to the IP address item to via the device current device information. You can access the client-end via this new address. Figure 5-33 5.8.2.7 DDNS The DDNS interface is shown as in Figure 5-34. The DDNS is to set to connect the various servers so that you can access the system via the server.
Parameter Function Server IP DDNS server IP address Server Port DDNS server port. Domain Name Your self-defined domain name. User The user name you input to log in the server. Password The password you input to log in the server. Update period Device sends out alive signal to the server regularly. You can set interval value between the device and DDNS server here. Quick DDNS and Client-end Introduction 1) Background Introduction Device IP is not fixed if you use ADSL to login the network.
Figure 5-35 5.8.2.9 Email The email interface is shown as in Figure 5-36. Figure 5-36 Please refer to the following sheet for detailed information. Parameter Function Enable Please check the box here to enable email function. SMTP Server Input server address and then enable this function. Port Default value is 25. You can modify it if necessary.
Parameter Function Anonymity For the server supports the anonymity function. You can auto login anonymously. You do not need to input the user name. password and the sender information. User Name The user name of the sender email account. Password The password of sender email account. Sender Sender email address. Authentication (Encryption mode) You can select SSL or none. Subject Input email subject here.
Figure 5-37 5.8.2.11 SNMP The SNMP interface is shown as in Figure 5-38. The SNMP allows the communication between the network management work station software and the proxy of the managed device. It is reserved for the 3rd party to develop. Figure 5-38 Please refer to the following sheet for detailed information. Parameter Function SNMP Port The listening port of the proxy program of the device. It is a UDP port not a TCP port. The value ranges from 1 to 65535.
Parameter Function Read Community It is a string. It is a command between the manage process and the proxy process. It defined the authentication, access control and the management relationship between one proxy and one group of the managers. Please make sure the device and the proxy are the same. The read community will read all the objects the SNMP supported in the specified name. The default setup is public. It is a string. It is a command between the manage process and the proxy process.
Please follow the steps listed below to use this function. Please set proxy server address, port, and sub-device name at the device-end. Please enable the auto register function, the device can auto register to the proxy server. Figure 5-40 5.8.2.14 Alarm Centre The alarm center interface is shown as below. See Figure 5-41. This interface is reserved for you to develop. System can upload alarm signal to the alarm center when local alarm occurs.
You need to implement server certificate again if you have changed device IP. You need to download root certificate if it is your first time to use HTTPS on current PC. Figure 5-42 5.8.2.15.1 Create Server Certificate If it is your first time to use this function, please follow the steps listed below. In Figure 5-42, click state name and etc. Click Create button. See Figure 5-43.
Figure 5-45 Click Open button, you can go to the following interface. See Figure 5-46. Figure 5-46 Click Install certificate button, you can go to certificate wizard. See Figure 5-47.
Figure 5-47 Click Next button to continue. Now you can select a location for the certificate. See Figure 5-48. Figure 5-48 Click Next button, you can see the certificate import process is complete. See Figure 5-49.
Figure 5-49 Click Finish button, you can see system pops up a security warning dialogue box. See Figure 5-50. Figure 5-50 Click Yes button, system pops up the following dialogue box, you can see the certificate download is complete. See Figure 5-51. Figure 5-51 5.8.2.15.3 View and set HTTPS port From Setup->Network->Connection, you can see the following interface. See Figure 5-52. You can see HTTPS default value is 443.
Figure 5-52 5.8.2.15.4 Login Open the browser and then input https://xx.xx.xx.xx:port. xx.xx.xx.xx: is your device IP or domain mane. Port is your HTTPS port. If you are using default HTTPS value 443, you do not need to add port information here. You can input https://xx.xx.xx.xx to access. Now you can see the login interface if your setup is right. 5.8.3 Event 5.8.3.1 Video detect 5.8.3.1.
Figure 5-53 Figure 5-54 236
Figure 5-55 Figure 5-56 Figure 5-57 238
Figure 5-58 Please refer to the following sheet for detailed information. Parameter Function Enable You need to check the box to enable motion detection function. Please select a channel from the dropdown list. Period Motion detection function becomes activated in the specified periods. See Figure 5-54. There are six periods in one day. Please draw a circle to enable corresponding period. Click OK button, system goes back to motion detection interface, please click save button to exit.
Parameter Function message screen if you enabled this function. Buzzer Check the box here to enable this function. The buzzer beeps when an alarm occurs. Alarm upload System can upload the alarm signal to the centre (Including alarm centre. Message When 3G network connection is OK, system can send out a message when motion detect occurs. Send Email If you enabled this function, System can send out an email to alert you when an alarm occurs.
Figure 5-59 5.8.3.1.3Tampering The tampering interface is shown as in Figure 5-60. After analysis video, system can generate a tampering alarm when the detected moving signal reached the sensitivity you set here. For detailed setups, please refer to chapter 5.8.3.1.1 motion detect for detailed information. Figure 5-60 5.8.3.2 Alarm Before operation, please make sure you have properly connected alarm devices such as buzzer. The input mode includes local alarm and network alarm. 5.8.3.2.
Figure 5-61 Figure 5-62 242
Figure 5-63 Please refer to the following sheet for detailed information. Parameter Function Enable You need to check the box to enable this function. Please select a channel from the dropdown list. Period This function becomes activated in the specified periods. There are six periods in one day. Please draw a circle to enable corresponding period. Select date. If you do not select, current setup applies to today only. You can select all week column to apply to the whole week.
Parameter Function Show message System can pop up a message to alarm you in the local host screen if you enabled this function. Buzzer Check the box here to enable this function. The buzzer beeps when an alarm occurs. Alarm upload System can upload the alarm signal to the centre (Including alarm centre). Send Email If you enabled this function, System can send out an email to alert you when an alarm occurs. Tour You need to click setup button to select tour channel.
setup. For setup information, please refer to chapter 5.8.3.2.1. Figure 5-65 5.8.3.2.4 IPC Offline Alarm The IPC offline alarm interface is shown as in Figure 5-66. System can generate an alarm once the network camera is offline. For setup information, please refer to chapter 5.8.3.2.1.
5.8.3.3 Abnormality It includes six types: No disk, disk error, disks no space, disconnect, IP conflict, MAC conflict. See Figure 5-67 through Figure 5-72.
Figure 5-71 Figure 5-72 Please refer to the following sheet for detailed information. Parameter Function Event Type The abnormal events include: No disk, disk error, disk no space, net disconnection, IP conflict and MAC conflict. You can set one or more items here. Less than: You can set the minimum percentage value here (For disk not space only). The device can alarm when capacity is not sufficient. You need to draw a circle to enable this function.
Parameter Function Buzzer Check the box here to enable this function. The buzzer beeps when an alarm occurs. 5.8.4 Storage 5.8.4.1 Schedule In this interfaces, you can add or remove the schedule record setup. See Figure 5-73. There are four record modes: general (auto), motion detect, alarm and MD&alarm. There are six periods in one day. You can view the current time period setup from the color bar. Green color stands for the general record/snapshot.
Figure 5-75 Please refer to the following sheet for detailed information. Parameter Function Channel Please select a channel from the dropdown list. Pre-record Please input pre-record time here. The value ranges from 0 to 30. Redundancy Check the box here to enable redundancy function. Please note this function is null if there is only one HDD. Snapshot Check the box here to enable snapshot function. Holiday Check the box here to enable holiday function.
Parameter Function 5/6/7. If you wan to save current setup of channel 1 to all channels, you can click the first box “ALL”. Click the OK button to save current copy setup. Click the OK button in the Encode interface, the copy function succeeded. 5.8.4.2 HDD Manager 5.8.4.2.1 Local Storage The local interface is shown as in Figure 5-76. Here you can see HDD information. You can also operate the read-only, read-write, redundancy (if there are more than on HDD) and format operation. Figure 5-76 5.8.4.2.
Figure 5-78 5.8.4.3 Record Control The interface is shown as in Figure 5-79. Figure 5-79 Please refer to the following sheet for detailed information. Parameter Function Channel Here you can view channel number. The number displayed here is the max channel amount of your device. Status There are three statuses: schedule, manual and stop. Schedule System enables auto record function as you set in record schedule setup (general, motion detect and alarm).
Manual It has the highest priority. Enable corresponding channel to record no matter what period applied in the record setup. Stop Stop current channel record no matter what period applied in the record setup. Start all/ stop all Check the corresponding All button, you can enable or disable all channels record. 5.8.4.4 RAID Manager Important Please make sure your purchased product support the RAID function, otherwise you can not see the following interface. 5.8.4.4.
Figure 5-81 5.8.4.5 Storage 5.8.4.5.1 Main Stream The main stream interface is shown as in Figure 5-82. Here you can set corresponding HDD group to save main stream. Figure 5-82 5.8.4.5.2 Sub Stream The sub stream interface is shown as in Figure 5-83. Here you can set corresponding HDD group to save sub stream.
Figure 5-83 5.8.4.5.3Snapshot The snapshot interface is shown as in Figure 5-84. Here you can set corresponding HDD group to save snapshot picture. Figure 5-84 5.8.5 Setting 5.8.5.1 General The general interface includes general, date/time and holiday setup. 5.8.5.1.1General The general interface is shown as in Figure 5-85.
Please refer to the following sheet for detailed information. Parameter Function Device ID It is to set device name. Device No. It is device channel number. Language You can select the language from the dropdown list. Please note the device needs to reboot to get the modification activated. Video Standard This is to display video standard such as PAL. HDD full Here is for you to select working mode when hard disk is full. There are two options: stop recording or rewrite.
Time Format There are two options: 24-H and 12-H. Time zone The time zone of the device. System time It is to set system time. It becomes valid after you set. Sync PC You can click this button to save the system time as your PC current time. DST Here you can set day night save time begin time and end time. You can set according to the date format or according to the week format. NTP You can check the box to enable NTP function. NTP server You can set the time server address.
5.8.5.2.1User name In this interface you can add/remove user and modify user name. See Figure 5-88. Figure 5-88 Add user: It is to add a name to group and set the user rights. See Figure 5-89. There are four default users: admin/888888/666666 and hidden user “default”. Except user 6666, other users have administrator right. The user 666666 can only have the monitor rights,. Hidden user “default” is for system interior use only and can not be deleted.
Modify user It is to modify the user property, belonging group, password and rights. See Figure 5-90. Modify password It is to modify the user password. You need to input the old password and then input the new password twice to confirm the new setup. Please click the OK button to save. Please note, the password ranges from 1-digit to 6-digit. It shall include the number only. For the user of the account rights, he can modify the password of other users. Figure 5-90 5.8.5.2.
Add group: It is to add group and set its corresponding rights. See Figure 5-92. Please input the group name and then check the box to select the corresponding rights. It includes: shutdown/reboot device, live view, record control, PTZ control and etc. Figure 5-92 Modify group Click the modify group button, you can see an interface is shown as in Figure 5-93. Here you can modify group information such as remarks and rights.
5.8.5.3 Display Display interface includes GUI, TV adjust, Tour and zero-channel encoding. 5.8.5.3.1Display Here you can set background color and transparency level. See Figure 5-94. Figure 5-94 Please refer to the following sheet for detailed information. Parameter Function Resolution There are four options: 1920×1080,1280×1024(default),1280×720,1024×768. Please note the system needs to reboot to activate current setup. Here is for you to adjust transparency. The value ranges from 128 to 255.
Figure 5-95 Please refer to the following sheet for detailed information. Parameter Function Enable tour Check the box here to enable tour function. Interval Here is for you to adjust transparency. The value ranges from 5 to 120s. The default setup is 5s. Here you can set window mode and channel group. System can support 1/4/8/9/16/25/36-window according to device channel amount. Here you can set motion detect tour/alarm tour window mode. System supports 1/8-window now.
Figure 5-96 5.8.5.5 Default The default setup interface is shown as in Figure 5-97. Here you can select Network/Event/Storage/Setting/Camera. Or you can check the All box to select all items. Figure 5-97 5.8.5.6 Import/Export The interface is shown as in Figure 5-98. This interface is for you to export or import the configuration files.
Please refer to the following sheet for detailed information. Parameter Function Browse Click to select import file. Import It is to import the local setup files to the system. Export It is to export the corresponding WEB setup to your local PC. 5.8.5.7 Auto maintain The auto maintain interface is shown as in Figure 5-99. Here you can select auto reboot and auto delete old files interval from the dropdown list. If you want to use the auto delete old files function, you need to set the file period.
5.8.5.9 RS232 The RS232 interface is shown as in Figure 5-101. Figure 5-101 Please refer to the following sheet for detailed information. Parameter Function Protocol Select the corresponding dome protocol. Default setup is console. Select the baud rate. Default setup is 115200. Baud Rate Data Bit The value ranges from 5 to 8. Default setup is 8. Stop bit There are two options: 1/2. Default setup is 1. Parity There are five options: none/odd/even/space/mark. Default setup is none. 5.8.5.
Figure 5-102 Figure 5-103 Please refer to the following sheet for detailed information. Parameter Function Channel Select speed dome connected channel. PTZ Type There are two options: local/remote. Please select remote type if you are connecting to the network PTZ. Protocol Select the corresponding dome protocol such as PELCOD. Address Set corresponding dome address. Default value is 1. Please note your setup here shall comply with your dome address; otherwise you can not control the speed dome.
Parameter Function setup. Parity 5.9 Default setup is none. Please set according to the speed dome dial switch setup. Information 5.9.1 Version The version interface is shown as in Figure 5-104. Here you can view record channel, alarm input/output information, software version, release date and etc. Please note the following information is for reference only. Figure 5-104 5.9.2 Log Here you can view system log. See Figure 5-105.
Parameter Function Type Start time Log types include: system operation, configuration operation, data operation, event operation, record operation, user management, log clear. Set the start time of the requested log. End time Set the end time of the requested log. Search You can select log type from the drop down list and then click search button to view the list. You can click the stop button to terminate current search operation.
Figure 5-107 Then please click File list button, you can see the corresponding files in the list. See Figure 5-108. Figure 5-108 Select a file you want to play and then click Play button, system can begin playback. You can select to playback in full-screen. Please note for one channel, system can not playback and download at the same time. You can use the playback control bar to implement various operations such as play, pause, stop, slow play, fast play and etc. See Figure 5-109.
Figure 5-109 Select the file(s) you want to download and then click download button, you can see an interface shown as in Figure 5-110. The Download button becomes Stop button and there is a process bar for your reference. Please go to you default file saved path to view the files.
Load more Click More button in Figure 5-110, you can see an interface shown as in Figure 5-111. It is for you to search record or picture. You can select record channel, record type and record time to download. Figure 5-111 Watermark Watermark interface is shown as in Figure 5-112.
5.11 Alarm Click alarm function, you can see an interface is shown as Figure 5-113. Here you can set device alarm type and alarm sound setup (Please make sure you have enabled audio function of corresponding alarm events.). Figure 5-113 Please refer to the following sheet for detailed information. Type Parameter Function Alarm Type Video loss System alarms when video loss occurs. Motion detection System alarms when motion detection alarm occurs.
Click log out button, system goes back to log in interface. See Figure 5-114. You need to input user name and password to login again. Figure 5-114 5.13 Un-install Web Control You can use web un-install tool “uninstall web.bat” to un-install web control. Please note, before you un-installation, please close all web pages, otherwise the un-installation might result in error.
6 Glossary DHCP: DHCP (Dynamic Host Configuration Protocol) is a network protocol. It is one of the TCP/IP protocol cluster. It is principally used to assign temporary IP addresses to computers on a network. DDNS: DDNS (Dynamic Domain Name Server) is a service that maps Internet domain names to IP addresses.
7 Appendix A HDD Capacity Calculation Calculate total capacity needed by each device according to video recording (video recording type and video file storage time). Step 1: According to Formula (1) to calculate storage capacity qi that is the capacity of each channel needed for each hour, unit Mbyte.
8 Appendix B Compatible Network Camera Please note all the models in the following list are for reference only. For those products not included in the list, please contact your local retailer or technical supporting engineer for detailed information. Manufact ure Model Version Video Encode Audio/Vid eo Protocol AXIS P1346 5.40.9.2 H264 √ ONVIF, Private P3344/P3344E 5.40.9.2 H264 √ ONVIF, Private H264 √ ONVIF, Private P5512 Q1604 5.40.3.2 H264 √ ONVIF, Private Q1604-E 5.40.
H264 √ Private XNETM112011 1229 H264 √ ONVIF VIPBL1.3MIR VF XNETM210011 1229 H264 √ ONVIF IGC-2050F XNETM210011 1229 H264 √ ONVIF CP-NC9-K 6.E.2.7776 H264 √ Private, ONVIF CP-NC9W-K 6.E.2.
LG Imatek Panasonic HICC-1300W 2.0.1.7 H264 √ ONVIF HICC-2300 2.0.0.21 H264 √ ONVIF HDZ20HDX H20130114NS A H264 √ ONVIF LW342-FP H264 √ Private LNB5100 H264 √ ONVIF KNC-B5000 H264 √ Private KNC-B5162 H264 √ Private KNC-B2161 H264 √ Private NP240/CH MPEG4 √ Private WV-NP502 MPEG4 √ Private H264 √ Private, H264 √ Private, ONVIF WV-SP102H 1.41 WV-SP105H WV-SP302H 1.41 H264 MPEG4 √ Private, ONVIF WV-SP306H 1.
Samsung DD4N-X 01.02.0015 MPEG4 √ Private DD423-X 01.02.0006 MPEG4 √ Private D5220 1.8.3-FC2-2012 0614-1.9320-A 1.8035 H264 √ Private SNB-3000P 2.41 H264 MPEG4 √ Private, ONVIF SNP-3120 1.22_110120_1 √ Private, ONVIF SNP-3370 1.21_110318 H264 MPEG4 MPEG4 √ Private SNB-5000 2.10_111227 H264 MPEG4 √ Private, ONVIF H264 MPEG4 √ Private SND-5080 Sony SANYO SNZ-5200 1.02_110512 H264 MPEG4 √ Private, ONVIF SNP-5200 1.04_110825 √ Private, ONVIF SNB-7000 1.
9 Appendix C Compatible Backup Device List Compatible USB drive list Manufacturer Model Capacity Sandisk Cruzer Micro 512M Sandisk Cruzer Micro 1G Sandisk Cruzer Micro 2G Sandisk Cruzer Freedom 256M Sandisk Cruzer Freedom 512M Sandisk Cruzer Freedom 1G Sandisk Cruzer Freedom 2G Kingston DataTraveler 1G Kingston 2G Kingston DataTraveler DataTraveler Kingston DataTraveler 2G Maxell USB Flash Stick 128M Maxell USB Flash Stick 256M Maxell USB Flash Stick 512M Maxell
Manufacturer Model Capacity Kingston Data Traveler Locker+ 32GB Netac U228 8GB Compatible SD Card List Please refer to the following sheet for compatible SD card brand. Brand Standard Capacity Card type Transcend SDHC6 16GB SD Kingston SDHC4 4GB SD Kingston SD 2GB SD Kingston SD 1GB SD Sandisk SDHC2 8GB Micro-SD Sandisk SD 1GB Micro-SD Compatible Portable HDD List Please refer to the following sheet for compatible portable HDD brand.
Manufacturer Model SONY AW-G170S Pioneer NVR-217CH Pioneer NVR-215CHG Compatible SATA HDD List Manufacturer Series Model Capacity Port Mode Seagate Seagate SV35.1 ST3250824SV 250G SATA Seagate Seagate SV35.1 ST3500641SV 500G SATA Seagate Seagate SV35.2 ST3250820SV 250G SATA Seagate Seagate SV35.2 ST3320620SV 320G SATA Seagate Seagate SV35.2 ST3500630SV 500G SATA Seagate Seagate SV35.2 ST3750640SV 750G SATA Seagate Seagate SV35.
Manufacturer Series Model Capacity Port Mode HD2 Seagate Seagate HD2 Pipeline ST3320311CS 250G SATA Seagate Seagate HD2 Pipeline ST3500414CS 500G SATA Seagate Seagate HD2 Pipeline ST3500312CS 500G SATA Seagate Seagate HD2 Pipeline ST31000424CS 1T SATA Seagate Seagate HD2 Pipeline ST31000322CS 1T SATA Seagate Seagate HD2 Pipeline ST1000VM002 1T SATA Seagate Seagate HD2 Pipeline ST1500VM002 1T SATA Seagate Seagate HD2 Pipeline ST2000VM002 2T SATA Seagate S
Manufacturer Series Model Capacity Port Mode Constellation ES Seagate Seagate Constellation ES ST2000NM0051 2T SATA Seagate Seagate Constellation ES ST1000NM0051 1T SATA Seagate Seagate Constellation ES ST500NM0051 500G SATA Seagate Seagate Constellation ES.2 ST33000650NS 3T SATA Seagate Seagate Constellation ES.2 ST32000645NS 2T SATA Seagate Seagate Constellation ES.2 ST33000651NS 3T SATA Seagate Seagate Constellation ES.
Series Model Capacity Port Mode Westem Digital WD Caviar RE16 WD3200YS-01PGB0 320G SATA Westem Digital WD Caviar RE2 WD5000YS-01MPB0 500G SATA Westem Digital WD AV—AVJS WD2500AVJS-63WDA0 500G SATA Westem Digital WD AV—AVJS WD3200AVJS-63WDA0 320G SATA Westem Digital WD AV—AVJS WD5000AVJS-63YJA0 500G SATA Westem Digital WDAV-GP—AVCS WD5000AVCS-63H1B1 500G SATA Westem Digital WDAV-GP—AVCS WD7500AVCS-63ZLB0 750G SATA Westem Digital WDAV-GP—AVCS WD3200AVCS 320G SATA We
Series Model Capacity Port Mode Westem Digital WDAV-GP—EVDS WD20EVDS-63T3B0 2T SATA Westem Digital WDAV-GP—AVDS WD5000AVDS-63U7B0 500G SATA Westem Digital WD AV-GP WD30EURS 3T SATA Westem Digital WD AV-GP WD25EURS 2.5T SATA Westem Digital WD AV-GP WD20EURS 2T SATA Westem Digital WD AV-GP WD15EURS 1.
Manufacturer Series Model Capacity Port Mode Hitachi HitachiCinemaStar™ 7K1000.B HCT721075SLA360 750G SATA Hitachi HitachiCinemaStar™ 7K1000.B HCT721010SLA360 1T SATA Maxtor DiamondMax 20 STM3320820AS 320G SATA Maxtor DiamondMax 20 STM3250820AS 250G SATA Compatible 2.
10 Appendix D Compatible CD/DVD Manufacturer Model Port Mode Type Sony DRX-S50U USB DVD-RW Sony DRX-S70U USB DVD-RW Sony AW-G170S SATA DVD-RW Samsung TS-H653A SATA DVD-RW Panasonic SW-9588-C SATA DVD-RW Sony DRX-S50U USB DVD-RW BenQ 5232WI USB DVD-RW 287
11 Appendix E Compatible Displayer List Brand Model Dimension (Unit: inch) BENQ LCD ET-0007-TA 19-inch (wide screen) DELL LCD E178FPc 17-inch BENQ LCD Q7T4 17-inch BENQ LCD Q7T3 17-inch LENOVO LCD LXB-L17C 17-inch SANGSUNG LCD LENOVO(CRT) 225BW 22-inch (wide screen) LXB-FD17069HB 17-inch LENOVO(CRT) LXB-HF769A 17-inch LENOVO(CRT) LX-GJ556D 17-inch Samsung (LCD) 2494HS 24-inch Samsung (LCD) P2350 23-inch Samsung (LCD) P2250 22-inch Samsung (LCD) P2370G 23-inch Samsung
12 Appendix F Toxic or Hazardous Materials or Elements Component Name Toxic or Hazardous Materials or Elements Pb Hg Cd Cr VI PBB PBDE Sheet Metal(Case) ○ ○ ○ ○ ○ ○ Plastic Parts Panel ○ ○ ○ ○ ○ ○ Circuit Board ○ ○ ○ ○ ○ ○ Fastener ○ ○ ○ ○ ○ ○ Wire and Cable/Ac Adapter ○ ○ ○ ○ ○ ○ Packing Material ○ ○ ○ ○ ○ ○ Accessories ○ ○ ○ ○ ○ ○ Note O: Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below th
