Computer Drive User Manual
Table Of Contents
- 1.0 Scope 1
- 2.0 Standards, compliance and reference documents 3
- 3.0 General description 7
- 4.0 Performance characteristics 11
- 5.0 Reliability specifications 15
- 6.0 Physical/electrical specifications 23
- 6.1 AC power requirements 23
- 6.2 DC power requirements 23
- 6.3 Power dissipation 29
- 6.4 Environmental limits 32
- 6.4.1 Temperature 32
- 6.4.2 Relative humidity 32
- 6.4.3 Effective altitude (sea level) 33
- 6.4.4 Shock and vibration 33
- 6.4.5 Acoustics 35
- 6.4.6 Air cleanliness 35
- 6.4.7 Corrosive environment 35
- 6.4.8 European Union Restriction of Hazardous Substances (RoHS) Directive 36
- 6.4.9 China Restriction of Hazardous Substances (RoHS) Directive 36
- 6.4.10 Electromagnetic susceptibility 36
- 6.5 Mechanical specifications 37
- 7.0 Defect and error management 39
- 8.0 Installation 43
- 9.0 Interface requirements 47
- 9.1 FC-AL features 47
- 9.1.1 Fibre Channel link service frames 47
- 9.1.2 Fibre Channel task management functions 48
- 9.1.3 Fibre Channel task management responses 48
- 9.1.4 Fibre Channel port login 49
- 9.1.5 Fibre Channel port login accept 50
- 9.1.6 Fibre Channel Process Login 50
- 9.1.7 Fibre Channel Process Login Accept 51
- 9.1.8 Fibre Channel fabric login 51
- 9.1.9 Fibre Channel fabric accept login 52
- 9.1.10 Fibre Channel Arbitrated Loop options 53
- 9.2 Dual port support 53
- 9.3 SCSI commands supported 54
- 9.4 Miscellaneous operating features and conditions 63
- 9.5 FC-AL physical interface 64
- 9.5.1 Physical characteristics 64
- 9.5.2 Connector requirements 65
- 9.5.3 Electrical description 65
- 9.5.4 Pin descriptions 65
- 9.5.5 FC-AL transmitters and receivers 66
- 9.5.6 Power 67
- 9.5.7 Fault LED Out 67
- 9.5.8 Active LED Out 68
- 9.5.9 Enable port bypass signals 68
- 9.5.10 Motor start controls 68
- 9.5.11 SEL_6 through SEL_0 ID lines 69
- 9.5.12 Device control codes 71
- 9.6 Signal characteristics 71
- 9.1 FC-AL features 47
- 10.0 Seagate Technology support services 75
- 1.0 Scope
- 2.0 Standards, compliance and reference documents
- 3.0 General description
- 4.0 Performance characteristics
- 5.0 Reliability specifications
- 6.0 Physical/electrical specifications
- 6.1 AC power requirements
- 6.2 DC power requirements
- 6.3 Power dissipation
- 6.4 Environmental limits
- 6.4.1 Temperature
- 6.4.2 Relative humidity
- 6.4.3 Effective altitude (sea level)
- 6.4.4 Shock and vibration
- 6.4.5 Acoustics
- 6.4.6 Air cleanliness
- 6.4.7 Corrosive environment
- 6.4.8 European Union Restriction of Hazardous Substances (RoHS) Directive
- 6.4.9 China Restriction of Hazardous Substances (RoHS) Directive
- 6.4.10 Electromagnetic susceptibility
- 6.5 Mechanical specifications
- 7.0 Defect and error management
- 8.0 Installation
- 9.0 Interface requirements
- 9.1 FC-AL features
- 9.1.1 Fibre Channel link service frames
- 9.1.2 Fibre Channel task management functions
- 9.1.3 Fibre Channel task management responses
- 9.1.4 Fibre Channel port login
- 9.1.5 Fibre Channel port login accept
- 9.1.6 Fibre Channel Process Login
- 9.1.7 Fibre Channel Process Login Accept
- 9.1.8 Fibre Channel fabric login
- 9.1.9 Fibre Channel fabric accept login
- 9.1.10 Fibre Channel Arbitrated Loop options
- 9.2 Dual port support
- 9.3 SCSI commands supported
- 9.4 Miscellaneous operating features and conditions
- 9.5 FC-AL physical interface
- 9.5.1 Physical characteristics
- 9.5.2 Connector requirements
- 9.5.3 Electrical description
- 9.5.4 Pin descriptions
- 9.5.5 FC-AL transmitters and receivers
- 9.5.6 Power
- 9.5.7 Fault LED Out
- 9.5.8 Active LED Out
- 9.5.9 Enable port bypass signals
- 9.5.10 Motor start controls
- 9.5.11 SEL_6 through SEL_0 ID lines
- 9.5.12 Device control codes
- 9.6 Signal characteristics
- 9.1 FC-AL features
- 10.0 Seagate Technology support services
78 Cheetah NS 10K.2 FC Product Manual, Rev. B
D
DAR 42
data block size
modifing the 9
data heads
read/write 11
data rate
internal 11
data transfer rate 12
data valid eye 73
Date code page command 54
DC power 65
requirements 23
defect and error management 39
defects 39
Deferred Auto-Reallocation 42
deferred error handling 63
description 7
DEV_CTRL_CODE 71
Device Behavior page command 54
device control code values 71
Device Identification page command 54
device selection IDs 43
devices 43
dimensions 37
Disable page out command 55
disc rotation speed 11
Disconnect/reconnect control (page 02h) command
54
Download microcode and save modes (5) 56
Download microcode mode (4) 56
Download microcode with offsets and save mode (7)
56
Download microcode with offsets mode (6) 56
drive 35
drive capacity
programmable 10
drive characteristics 11
drive ID 43
drive ID/option select headers 43
drive mounting 37, 44
drive orientation 43
drive select 65
driver signals 72
drivers and receivers 8
dual port support 53
E
electrical
description of connector 65
signal characteristics 71
specifications 23
electromagnetic compatibility 3
electromagnetic susceptibility 36
EMI requirements 3
enable bypass
port A 68
port B 68
signal 68
state 16
Enclosure Services interface 65
Enclosure services page command 55
environmental
limits 32
requirements 15
environmental control 35
error
detection mechanisms, FC 16
management 39
rates 15
error correction code
96-bit Reed-Solomon 8
Error recovery page (01h) command 54
errors 39
EU RoHS directive 36
extended link service
frames 47
reply frames 47
Extended sense command 54
Extent reservation command 57
F
fabric 52
Fabric Address Notification (FAN) 47
Fabric Login (FLOGI) 47
FAN 52
fault LED out signal 67
FC differential input 72
FC-AL
document 5
interface 43, 65
options supported 53
physical interface 64
SCA device connector, illustrated 65
selective reset 63
FCC rules and regulations 3
FCP
for SCSI, document 5
response codes 48
task management functions 48
FC-PH document 5
features 8
interface 47
Fibre Channel documents 5
Fibre Channel Interface Control page (19h) 55
Fibre Channel Interface Manual 1, 3
Fibre Channel Services 47
Field pointer bytes command 54
firmware 8