.......................................... Barracuda 5400.1 Family .......................................... ST340015A .......................................... .......................................... .......................................... Ultra ATA Interface Drives .......................................... Product Manual ..........................................
....................................... Barracuda 5400.1 Family ....................................... ST340015A ....................................... ....................................... ....................................... Ultra ATA Interface Drives ....................................... Product Manual .......................................
© 2003–2004 Seagate Technology LLC All rights reserved Publication number: 100256411, Rev. G May 2004 Seagate, Seagate Technology, and the Seagate logo are either registered trademarks or trademarks of Seagate Technology LLC. Barracuda, DiscWizard, SeaFONE, SeaShell, SeaShield, SeaTDD, and 3D Defense System are either registered trademarks or trademarks of Seagate Technology LLC. Other product names are registered trademarks or trademarks of their owners.
Barracuda 5400.1 Product Manual, Rev. G iii Contents 1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1 Specification summary table . . . . . . . . . . . . . . . . . . . . . . . 3 2.2 Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2.3 Default logical geometry . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2.
iv Barracuda 5400.1 Product Manual, Rev. G 4.1.1 4.1.2 4.1.3 4.1.4 5.0 Supported ATA commands. . . . . . . . . . . . . . . . 29 Identify Device command . . . . . . . . . . . . . . . . . 31 Set Features command. . . . . . . . . . . . . . . . . . . 36 S.M.A.R.T. commands . . . . . . . . . . . . . . . . . . . 38 Seagate Technology support services . . . . . . . . . . . . . . . . . . .
Barracuda 5400.1 Product Manual, Rev. G v List of Figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Typical 5V startup and operation current profile . . . . . . . . . Typical 12V startup and operation current profile . . . . . . . . Breather filter hole location . . . . . . . . . . . . . . . . . . . . . . . . . Master/slave jumper settings . . . . . . . . . . . . . . . . . . . . . . . Ultra ATA cable connectors . . . . . . . . . . . . . . . . . . . . . . . .
vi Barracuda 5400.1 Product Manual, Rev.
Barracuda 5400.1 Product Manual, Rev. G 1.0 1 Introduction This manual describes the functional, mechanical and interface specifications for Seagate® Barracuda® 5400.1 ST340015A model drives. This drive provides the following key features: • Low power consumption. • High instantaneous (burst) data transfer rates (up to 100 Mbytes per second) using Ultra DMA mode 5. • Giant magnetoresistive (GMR) recording heads and EPRML technology provide the drives with increased areal density.
2 Barracuda 5400.1 Product Manual, Rev.
Barracuda 5400.1 Product Manual, Rev. G 2.0 3 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate ST340015A model drives. 2.1 Specification summary table The specifications listed in this table are for quick reference. For details on specification measurement or definition, see the appropriate section of this manual.
4 Barracuda 5400.1 Product Manual, Rev.
Barracuda 5400.1 Product Manual, Rev. G Drive specification ST340015A Idle mode (typical) 5.0 watts Standby mode (typical) 1.4 watts Sleep mode (typical) 1.
6 Barracuda 5400.1 Product Manual, Rev. G 2.2 Formatted capacity Model Formatted capacity Guaranteed sectors Bytes per sector ST340015A 40 Gbytes 78,165,360 512 2.3 Default logical geometry Cylinders Read/write heads Sectors per track 16,383 16 63 LBA mode When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above. 2.
Barracuda 5400.1 Product Manual, Rev. G 2.5 Recording and interface technology Interface ATA Recording method GPRML detector with NPML post processor Recording density BPI (bits/inch max) 475,127 Track density TPI (tracks/inch max) 94,000 Areal density (Mbits/inch2 max) 49,888 Spindle speed (RPM) (± 0.2%) 5,800 Internal data transfer rate (Mbits/sec) 511 I/O data transfer rate (Mbytes/sec max) 16.
8 2.7 Barracuda 5400.1 Product Manual, Rev. G Seek time Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using drive diagnostics. The specifications in the table below are defined as follows: • Track-to-track seek time is an average of all possible single-track seeks in both directions. • Average seek time is a true statistical random average of at least 5,000 measurements of seeks between random tracks, less overhead.
Barracuda 5400.1 Product Manual, Rev. G 2.9.1 9 Power consumption Power requirements for the drives are listed in the table on page 10. Typical power measurements are based on an average of drives tested, under nominal conditions, using 5.0V and 12.0V input voltage at 25°C ambient temperature. • Spinup power Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed.
10 Barracuda 5400.1 Product Manual, Rev. G Power dissipation (watts) Spinup Average (watts, 25° C) — 5V typ amps 12V typ amps 1.20 (max) 2.0 (max) Idle 5.0 0.46 0.23 Idle* (with offline activity) 8.2 1.11 0.22 Operating 40% r/w, 40% seek, 20% inop. 6.6 0.59 0.30 Seeking 7.3 0.47 0.39 Standby 1.4 0.24 0.02 Sleep 1.0 0.16 0.02 *During periods of drive idle, some offline activity may occur according to the S.M.A.R.T.
Barracuda 5400.1 Product Manual, Rev. G 2.9.1.1 11 Typical current profile 3.0 2.5 +5 Volt Current during spindle start — Typical Amperes 2.0 Amps 1.5 1.0 0.5 0.0 0 2 4 6 8 10 12 14 16 Seconds Figure 1. Typical 5V startup and operation current profile 6.0 5.0 +12 Volt Current during spindle start — Typical Amperes 4.0 Amps 3.0 2.0 1.0 0.0 0.0 2 4 6 8 10 12 14 16 Seconds Figure 2.
12 2.9.2 Barracuda 5400.1 Product Manual, Rev. G Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on the +12 volt line or an equivalent 15-ohm resistive load on the +5 volt line. • Using 12-volt power, the drive is expected to operate with a maximum of 120 mV peak-to-peak square-wave injected noise at up to 10 MHz.
Barracuda 5400.1 Product Manual, Rev. G 13 Standby mode automatically after the drive has been inactive for a specifiable length of time. The standby timer delay is established using a Standby or Idle command. In Standby mode, the drive buffer is enabled, the heads are parked and the spindle is at rest. The drive accepts all commands and returns to Active mode any time disc access is necessary. • Sleep mode The drive enters Sleep mode after receiving a Sleep command from the host.
14 2.10.2 Barracuda 5400.1 Product Manual, Rev. G Temperature gradient Operating: 20°C per hour (68°F per hour max), without condensation Nonoperating: 30°C per hour (86°F per hour max) 2.10.3 Humidity 2.10.3.1 Relative humidity Operating: 5% to 90% noncondensing (30% per hour max) Nonoperating: 5% to 95% noncondensing (30% per hour max) 2.10.3.2 Wet bulb temperature Operating: 33°C (91.4°F max) Nonoperating: 40.0°C (104°F max) 2.10.4 Altitude Operating: –60.
Barracuda 5400.1 Product Manual, Rev. G 2.10.5 15 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis. 2.10.5.1 Operating shock These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 63 Gs based on half-sine shock pulses of 2 msec. Shocks should not be repeated more than two times per second. 2.10.5.
16 Barracuda 5400.1 Product Manual, Rev. G 2.11 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All measurements are consistent with ISO document 7779. Sound power measurements are taken under essentially free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward. Note. For seek mode tests, the drive is placed in seek mode only.
Barracuda 5400.1 Product Manual, Rev. G 2.
18 Barracuda 5400.1 Product Manual, Rev. G 2.14 Agency certification 2.14.1 Safety certification The drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections of IEC950 and EN 60950 as tested by TUV North America. 2.14.2 Electromagnetic compatibility Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Electromagnetic Compatibility Directive (89/336/ EEC).
Barracuda 5400.1 Product Manual, Rev. G 19 Australian C-Tick (N176) If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZS3548 1995 and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communication Authority (ACA). 2.14.3 FCC verification These drives are intended to be contained solely within a personal computer or similar enclosure (not attached as an external device).
20 Barracuda 5400.1 Product Manual, Rev.
Barracuda 5400.1 Product Manual, Rev. G 3.0 21 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static discharge precautions After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards. Observe the following standard handling and static-discharge precautions: Caution: • The SeaShell™ replaces electrostatic discharge (ESD) bags.
22 3.2 Barracuda 5400.1 Product Manual, Rev. G Breather filter hole precautions This section contains information regarding the precautions which should be taken regarding the breather filter hole in Seagate hard disc drives. Proper precautions should be taken to ensure full functionality and prevent possible damage to the drive. Breather Hole Do not cover or seal. Figure 3. Breather filter hole location Caution: Do not cover, seal, or insert any object into this hole.
Barracuda 5400.1 Product Manual, Rev. G 3.3 Jumper settings 3.3.1 Master/slave configuration 23 The options jumper block shown in Figure 4 is used to configure the drive for operation. It is the 8-pin dual header between the interface connector and the power connector. Use the following settings to configure the drive as a master or a slave. Master or single drive. The drive is configured at the factory for a master or single-drive operation with a jumper set on pins 7 and 8. Drive as slave.
24 Barracuda 5400.1 Product Manual, Rev. G 3.3.3 Ultra ATA/100 cable An 80-conductor 40-pin cable is required to run Ultra DMA mode 3, mode 4 and mode 5. This cable uses even-numbered conductors connected to the ground pins to improve signal integrity. Master Pin 1 Slave Note. If you are using a 40-pin 80-conductor cable, attach the blue connector to the motherboard, the black connector to the master drive, and the grey connector Co Mo mpu to the slave. the ter r bo ard Figure 5. Note. 3.
Barracuda 5400.1 Product Manual, Rev. G 25 4.000 in. (101.600 mm) Notes: 1. Dimensions are shown in inches (mm) Dimensions are per SFF-8301 specification 0.787 in. max (19.99 mm) 0.250 in. max (6.350 mm) 0.226 in. (5.750 mm) 2.229 in. (56.616 mm) 2.829 in. (71.856 mm) 1.140 +0.024 0.015 in. 3.717 – 0.30 in. (94.406 – 0.762 mm) (28.956 +0.635 0.381 mm) 2X 1.645 +0.020 0.010 in. 1.683 +0.025 0.015 in. (41.783 +0.508 0.254 mm) (41.605 +0.635 0.381 mm) 4.000 +0.025 0.015 in. (101.60 +0.635 0.
26 Barracuda 5400.1 Product Manual, Rev.
Barracuda 5400.1 Product Manual, Rev. G 4.0 27 ATA interface These drives use the industry-standard ATA task file interface that supports 16-bit data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–5. The drive also supports the use of the IORDY signal to provide reliable high-speed data transfers. You can use a daisy-chain cable to connect two drives to a single AT host bus.
28 Barracuda 5400.1 Product Manual, Rev.
Barracuda 5400.1 Product Manual, Rev. G 4.1.1 29 Supported ATA commands The following table lists ATA-standard commands that the drive supports. Barracuda 5400.1 drives support ATA-7 specifications. For a detailed description of the ATA commands, refer to the Draft ATA-7 Standard. See “S.M.A.R.T. commands” on page 38 for details and subcommands used in the S.M.A.R.T. implementation.
30 Barracuda 5400.1 Product Manual, Rev.
Barracuda 5400.1 Product Manual, Rev. G Command name 31 Command code (in hex) ATA-standard power-management commands Check Power Mode 98H or E5H Idle 97H or E3H Idle Immediate 95H or E1H Sleep 99H or E6H Standby 96H or E2H Standby Immediate 94H or E0H ATA-standard security commands Security Set Password F1H Security Unlock F2H Security Erase Prepare F3H Security Erase Unit F4H Security Freeze Lock F5H Security Disable Password F6H 4.1.
32 Barracuda 5400.1 Product Manual, Rev.
Barracuda 5400.1 Product Manual, Rev. G 33 Word Description Value 54 Number of current logical cylinders xxxxH 55 Number of current logical heads xxxxH 56 Number of current logical sectors per log- xxxxH ical track 57–58 Current capacity in sectors 59 Number of sectors transferred during a xxxxH Read Multiple or Write Multiple command 60–61 Total number of user-addressable LBA sectors available xxxxH ST340015A = 80,022,600 (see Section 2.
34 Barracuda 5400.1 Product Manual, Rev.
Barracuda 5400.1 Product Manual, Rev. G Note. 35 See the bit descriptions below for words 63, 88, 93 and 94 of the Identify Drive data: Description (if bit is set to 1) Bit Word 63 0 Multiword DMA mode 0 is supported. 1 Multiword DMA mode 1 is supported. 2 Multiword DMA mode 2 is supported. 8 Multiword DMA mode 0 is currently active. 9 Multiword DMA mode 1 is currently active. 10 Multiword DMA mode 2 is currently active. Bit Word 88 0 Ultra DMA mode 0 is supported.
36 Barracuda 5400.1 Product Manual, Rev. G 4.1.3 Set Features command This command (EFH) controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted. Power-on default has the read look-ahead and write caching features enabled.
Barracuda 5400.1 Product Manual, Rev. G F1H Note. 37 Report full capacity available At power-on, or after a hardware or software reset, the default values of the features are as indicated above.
38 4.1.4 Barracuda 5400.1 Product Manual, Rev. G S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for disc drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable. S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.
Barracuda 5400.1 Product Manual, Rev. G 5.0 39 Seagate Technology support services Online Services Internet www.seagate.com for information about Seagate products and services. Worldwide support is available 24 hours daily by e-mail for your questions. Presales Support: www.seagate.com/support/email/email_presales.html or DiscPresales@Seagate.com Technical Support: www.seagate.com/support/email/email_disc_support.html or DiscSupport@Seagate.com mySeagate my.seagate.
40 Barracuda 5400.1 Product Manual, Rev. G Seagate Online Store US customers can purchase Seagate disc drives 24 hours daily at www.seagate.com/buy/online/. Automated Phone Services SeaFONE® (1-800-SEAGATE) is the Seagate toll-free number (1-800-7324283) to access our automated self-help and directory assistance for Seagate support services.
Barracuda 5400.1 Product Manual, Rev. G 41 USA/Canada/Latin America Support Services Presales Support Call Center Americas Toll-free 1-877-271-3285 Direct dial +1-405-324-4730 FAX +1-405-324-4704 Direct dial +1-405-324-4770 FAX +1-405-324-4702 Toll-free 1-800-468-3472 Direct dial +1-405-324-4720 FAX / Internet +1-405-324-4722 1-800-636-6349 +1-905-660-4936 1-800-624-9857 +1-905-890-3099 +1-905-660-4951 www.memofix.com +1-905-890-3977 www.adtech1.
42 Barracuda 5400.1 Product Manual, Rev. G European Support Services For European presales, technical support, and warranty service, dial the tollfree number for your specific country. If your country is not listed here, dial our European call center at +31-20-316-7222 from 8:30 A.M. to 5:00 P.M. (Central Europe time) Monday through Friday. The European call center is located in Amsterdam, The Netherlands.
Barracuda 5400.1 Product Manual, Rev. G 43 Asia/Pacific Support Services For Asia/Pacific presales and technical support, dial the toll-free number for your specific country. The Asia/Pacific toll-free numbers are available from 6:00 A.M. to 10:45 A.M. and 12:00 P.M. to 6:00 P.M. (Australian Eastern time) Monday through Friday, except as noted. If your country is not listed here, direct dial one of our technical support locations.
44 Barracuda 5400.1 Product Manual, Rev.
Barracuda 5400.1 Product Manual, Rev.
46 Barracuda 5400.1 Product Manual, Rev.
Barracuda 5400.1 Product Manual, Rev. G R radiated RF immunity 17 radio and television interference 19 Radio frequency (RF) 17 random track location 9 Read Buffer 29 Read DMA 29 read errors 17 Read Multiple 1, 29 Read Sectors 29 Read Verify Sectors 29 read/write heads 6 read/write power and current 9 Recalibrate 29 recording and interface technology 7 recording density 7 recording heads 1 recording method 7 register 36 relative humidity 14 reliability 17 resistance 12 resistive load 12 RF 17 S S.M.A.R.T.
48 U UL 1950 18 Ultra ATA/100 24 Ultra DMA 24 V vibration 15 voltage 12 voltage dips, interrupts 17 voltage tolerance 12 W weight 7 wet bulb temperature 14 width 7 Write Buffer 30 Write DMA 30 Write Multiple 1, 30 Write Sectors 30 Barracuda 5400.1 Product Manual, Rev.
Seagate Technology LLC 920 Disc Drive, Scotts Valley, California 95066-4544, USA Publication Number: 100256411, Rev.
