Datasheet
Table Of Contents
- 1.0 Introduction 1
- 2.0 Drive specifications 3
- 2.1 Formatted capacity 8
- 2.2 Default logical geometry 8
- 2.3 Recording and interface technology 8
- 2.4 Physical characteristics 9
- 2.5 Access time 9
- 2.6 Start/stop times 9
- 2.7 Power specifications 10
- 2.8 Environmental specifications 14
- 2.9 Acoustics 16
- 2.10 Electromagnetic immunity 16
- 2.11 Reliability 17
- 2.12 Agency certification 17
- 2.13 Environmental protection 19
- 2.14 Corrosive environment 19
- 3.0 Configuring and mounting the drive 21
- 4.0 Serial ATA (SATA) interface 25
- 5.0 Seagate Technology support services 35
- Figure 1. Serial ATA connectors 22
- Figure 2. Attaching SATA cabling 22
- Figure 3. Mounting dimensions (2.0, 1.5 and 1.0 TB models) 23
- Figure 4. Mounting dimensions (500 GB models) 24
- 1.0 Introduction
- 2.0 Drive specifications
- 2.1 Formatted capacity
- 2.2 Default logical geometry
- 2.3 Recording and interface technology
- 2.4 Physical characteristics
- 2.5 Access time
- 2.6 Start/stop times
- 2.7 Power specifications
- 2.8 Environmental specifications
- 2.9 Acoustics
- 2.10 Electromagnetic immunity
- 2.11 Reliability
- 2.12 Agency certification
- 2.13 Environmental protection
- 2.14 Corrosive environment
- 3.0 Configuring and mounting the drive
- 4.0 Serial ATA (SATA) interface
- 5.0 Seagate Technology support services
- Index

30 Barracuda LP Series SATA Product Manual, Rev. B
60–61
Total number of user-addressable LBA sectors available
(see Section 2.1 for related information)
*Note: The maximum value allowed in this field is: 0FFFFFFFh
(268,435,455 sectors, 137 Gbytes). Drives with capacities over 137
Gbytes will have 0FFFFFFFh in this field and the actual number of
user-addressable LBAs specified in words 100-103. This is required
for drives that support the 48-bit addressing feature.
0FFFFFFFh*
62 Retired 0000
H
63
Multiword DMA active and modes supported
(see note following this table)
xx07
H
64 Advanced PIO modes supported (modes 3 and 4 supported) 0003
H
65 Minimum multiword DMA transfer cycle time per word (120 nsec) 0078
H
66
Recommended multiword DMA transfer cycle time per word
(120 nsec)
0078
H
67 Minimum PIO cycle time without IORDY flow control (240 nsec) 00F0
H
68 Minimum PIO cycle time with IORDY flow control (120 nsec) 0078
H
69–74 ATA-reserved 0000
H
75 Queue depth 0000
H
76 Serial ATA capabilities xxxx
H
77 Reserved for future Serial ATA definition xxxx
H
78 Serial ATA features supported xxxx
H
79 Serial ATA features enabled xxxx
H
80 Major version number 003E
H
81 Minor version number 0000
H
82 Command sets supported 364B
H
83 Command sets supported 7C03
H
84
Command sets support extension
(see note following this table)
4003
H
See Word 108-111 note.
(4003H = 0100000000000011
binary)
85 Command sets enabled 30xx
H
86 Command sets enabled 0001
H
87 Command sets enable extension 4000
H
88 Ultra DMA support and current mode (see note following this table) xx3F
H
89 Security erase time 0000
H
90 Enhanced security erase time 0000
H
92 Master password revision code FFFE
H
93 Hardware reset value xxxx
H
95–99 ATA-reserved 0000
H
100–103
Total number of user-addressable LBA sectors available (see Section
2.1 for related information). These words are required for drives that
support the 48-bit addressing feature. Maximum value:
0000FFFFFFFFFFFFh.
ST32000542AS = 3,907,029,168
ST31500541AS = 2,930,277,168
ST31000520AS = 1,953,525,168
ST3500412AS = 488,397,168
104–107 ATA-reserved 0000
H
Word Description Value