Product Manual Barracuda 7200.9 PATA ® ST3500841A ST3500641A ST3400833A ST3400633A ST3320833A ST3320633A ST3300822A ST3300622A ST3250824A ST3250624A 100389997 Rev.
©2006-2007, Seagate Technology LLC All rights reserved. Publication number: 100389997, Rev. F August 2007 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Barracuda, SeaTools and SeaTDD are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries.
Contents 1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.1 Specification summary table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2.2 Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . .
ii Barracuda 7200.9 PATA Product Manual, Rev.
List of Figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Typical 5V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Typical 12V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Breather filter hole location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Master/slave jumper settings . . . . . . . . . . . . . .
iv Barracuda 7200.9 PATA Product Manual, Rev.
1.0 Introduction This manual describes the functional, mechanical and interface specifications for the following Seagate® Barracuda® 7200.
2 Barracuda 7200.9 PATA Product Manual, Rev.
2.0 Drive specifications Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the following drive models: ST3500841A ST3300822A ST3160212A ST3500641A ST3300622A ST3120814A ST3400833A ST3250824A ST3120213A ST3400633A ST3250624A ST3802110A ST3320833A ST3200827A ST3402111A ST3320633A ST3160812A 2.
Table 1: Drive specifications summary for 500 Gbyte models Drive specification 4 ST3500841A Formatted Gbytes (512 bytes/sector)* 500 Guaranteed sectors 976,773,168 Bytes per sector 512 Default sectors per track 63 Default read/write heads 16 Default cylinders 16,383 ST3500641A Recording density, KBPI (kbits/in max) 790.1 Track density, KTPI (ktracks/in avg.) 124.5 Areal density, (Gbits/in2 avg) 97.96 Spindle speed (RPM) 7,200 Internal data transfer rate (Mbits/sec max) 815.
Drive specification ST3500841A ST3500641A Vibration, nonoperating 5–22 Hz: 0.25 Gs, Limited displacement 22–350 Hz: 5.0 Gs 350–500 Hz: 1.0 Gs Drive acoustics, sound power (bels) Idle** 2.8 (typical) 3.0 (max) Quiet seek 3.2 (typical) 3.4 (max) Nonrecoverable read errors 1 per 1014 bits read Annualized Failure Rate (AFR) 0.34% Warranty 5 years on distribution units. To determine the warranty for a specific drive, use a web browser to access the following web page: www.seagate.
Table 2: Drive specifications summary for 400 Gbyte models Drive specification 6 ST3400633A Formatted Gbytes (512 bytes/sector)* 400 Guaranteed sectors 781,422,768 Bytes per sector 512 Default sectors per track 63 Default read/write heads 16 Default cylinders 16,383 Recording density, KBPI (kbits/in max) 790.1 Track density, KTPI (ktracks/in avg.) 124.5 Areal density, (Gbits/in2 avg) 97.69 Spindle speed (RPM) 7,200 ST3400833A Internal data transfer rate (Mbits/sec max) 815.
Drive specification ST3400633A ST3400833A Vibration, nonoperating 5–22 Hz: 0.25 Gs, Limited displacement 22–350 Hz: 5.0 Gs 350–500 Hz: 1.0 Gs Drive acoustics, sound power (bels) Idle** 2.8 (typical) 3.0 (max) Quiet seek 3.2 (typical) 3.4 (max) Nonrecoverable read errors 1 per 1014 bits read Annualized Failure Rate (AFR) 0.34% Warranty 5 years on distribution units. To determine the warranty for a specific drive, use a web browser to access the following web page: www.seagate.
Table 3: Drive specifications summary for 320 Gbyte models Drive specification 8 ST3320633A Formatted Gbytes (512 bytes/sector)* 320 Guaranteed sectors 625,142,448 Bytes per sector 512 Default sectors per track 63 Default read/write heads 16 Default cylinders 16,383 Recording density, KBPI (kbits/in max) 790.1 Track density, KTPI (ktracks/in avg.) 124.5 Areal density, (Gbits/in2 avg) 97.69 Spindle speed (RPM) 7,200 ST3320633A Internal data transfer rate (Mbits/sec max) 867.
Drive specification ST3320633A ST3320633A Vibration, nonoperating 5–22 Hz: 0.25 Gs, Limited displacement 22–350 Hz: 5.0 Gs 350–500 Hz: 1.0 Gs Drive acoustics, sound power (bels) Idle** 2.7 (typical) 2.9 (max) Quiet seek 3.0 (typical) 3.2 (max) Nonrecoverable read errors 1 per 1014 bits read Annualized Failure Rate (AFR) 0.34% Warranty 5 years on distribution units. To determine the warranty for a specific drive, use a web browser to access the following web page: www.seagate.
Table 4: Drive specifications summary for 300 Gbyte models Drive specification ST3300622A Formatted Gbytes (512 bytes/sector)* 300 Guaranteed sectors 586,072,368 Bytes per sector 512 Default sectors per track 63 Default read/write heads 16 Default cylinders 16,383 Recording density, KBPI (kbits/in max) 790.1 Track density, KTPI (ktracks/in avg.) 124.5 Areal density, (Gbits/in2 avg) 97.69 Spindle speed (RPM) 7,200 ST3300822A Internal data transfer rate (Mbits/sec max) 867.
Drive specification ST3300622A ST3300822A Vibration, nonoperating 5–22 Hz: 0.25 Gs, Limited displacement 22–350 Hz: 5.0 Gs 350–500 Hz: 1.0 Gs Drive acoustics, sound power (bels) Idle** 2.7 (typical) 2.9 (max) Quiet seek 3.0 (typical) 3.2 (max) Nonrecoverable read errors 1 per 1014 bits read Annualized Failure Rate (AFR) 0.34% Warranty 5 years on distribution units. To determine the warranty for a specific drive, use a web browser to access the following web page: www.seagate.
Table 5: Drive specifications summary for 250 and 200 Gbyte models Drive specification ST3250624A ST3250824A ST3200827A Formatted Gbytes (512 bytes/sector)* 250 200 Guaranteed sectors 488,397,168 390,721,968 Bytes per sector 512 Default sectors per track 63 Default read/write heads 16 Default cylinders 16,383 Recording density, KBPI (kbits/in max) 790.1 Track density, KTPI (ktracks/in avg.) 124.5 Areal density, (Gbits/in2 avg) 97.
Drive specification ST3250624A ST3250824A Vibration, nonoperating 5–22 Hz: 0.25 Gs, Limited displacement 22–350 Hz: 5.0 Gs 350–500 Hz: 1.0 Gs ST3200827A Drive acoustics, sound power (bels) Idle** 2.7 (typical) 2.9 (max) Quiet seek 3.0 (typical) 3.2 (max) Nonrecoverable read errors 1 per 1014 bits read Annualized Failure Rate (AFR) 0.34% Warranty 5 years on distribution units. To determine the warranty for a specific drive, use a web browser to access the following web page: www.seagate.
Table 6: Drive specifications summary for 160 Gbyte models Drive specification ST3160812A Formatted Gbytes (512 bytes/sector)* 160 Guaranteed sectors 312,581,808 Bytes per sector 512 Default sectors per track 63 Default read/write heads 16 Default cylinders 16,383 Recording density, KBPI (kbits/in max) 840.0 Track density, KTPI (ktracks/in avg.) 141.5 Areal density, (Gbits/in2 avg) 119.0 Spindle speed (RPM) 7,200 Internal data transfer rate (Mbits/sec max) 867.
Drive specification ST3160812A ST3160212A Vibration, nonoperating 5–22 Hz: 0.25 Gs, Limited displacement 22–350 Hz: 5.0 Gs 350–500 Hz: 1.0 Gs Drive acoustics, sound power (bels) Idle** 2.5 (typical) 2.7 (max) Quiet seek 2.8 (typical) 3.0 (max) Nonrecoverable read errors 1 per 1014 bits read Annualized Failure Rate (AFR) 0.34% Warranty 5 years on distribution units. To determine the warranty for a specific drive, use a web browser to access the following web page: www.seagate.
Table 7: Drive specifications summary for 120 Gbyte models Drive specification ST3120814A Formatted Gbytes (512 bytes/sector)* 120 Guaranteed sectors 234,441,648 Bytes per sector 512 Default sectors per track 63 Default read/write heads 16 Default cylinders 16,383 ST3120213A Recording density, KBPI (kbits/in max) 840.0 Track density, KTPI (ktracks/in avg.) 141.5 Areal density, (Gbits/in2 avg) 119.0 Spindle speed (RPM) 7,200 Internal data transfer rate (Mbits/sec max) 867.
Drive specification ST3120814A ST3120213A Vibration, nonoperating 5–22 Hz: 0.25 Gs, Limited displacement 22–350 Hz: 5.0 Gs 350–500 Hz: 1.0 Gs Drive acoustics, sound power (bels) Idle** 2.5 (typical) 2.7 (max) Quiet seek 2.8 (typical) 3.0 (max) Nonrecoverable read errors 1 per 1014 bits read Annualized Failure Rate (AFR) 0.34% Warranty 5 years on distribution units. To determine the warranty for a specific drive, use a web browser to access the following web page: www.seagate.
Table 8: Drive specifications summary for 80 and 40 Gbyte models Drive specification ST3802110A ST3402111A Formatted Gbytes (512 bytes/sector)* 80 40 Guaranteed sectors 156,301,488 78,165,360 Bytes per sector 512 Default sectors per track 63 Default read/write heads 16 Default cylinders 16,383 Recording density, KBPI (kbits/in max) 840.0 611.5 Track density, KTPI (ktracks/in avg.) 141.5 103.9 Areal density, (Gbits/in2 avg) 119.0 63.
Drive specification ST3802110A ST3402111A Vibration, nonoperating 5–22 Hz: 0.25 Gs, Limited displacement 22–350 Hz: 5.0 Gs 350–500 Hz: 1.0 Gs Drive acoustics, sound power (bels) Idle** 2.5 (typical) 2.7 (max) 2.0 (typical) 2.3 (max) Quiet seek 2.7 (typical) 2.9 (max) 2.4 (typical) 2.6 (max) Nonrecoverable read errors 1 per 1014 bits read Annualized Failure Rate (AFR) 0.34% Warranty 5 years on distribution units.
2.
2.4 Recording and interface technology Interface ATA Recording method 16/17 EPRML Recording density KBPI (kbits/inch max) 790.1 (500, 400, 320, 300, 250 and 200GB models) 840.0 (160, 120 and 80GB models) 611.5 (40GB model) Track density KTPI (ktracks/inch avg) 124.5 (500, 400, 320, 300, 250 and 200GB models) 141.5 (160, 120 and 80GB models) 103.9 (40GB model) Areal density (Gbits/inch2 avg) 97.69 (500, 400, 320, 300, 250 and 200GB models) 119.0 (160, 120 and 80GB models) 63.
2.5 Physical characteristics Drive specification Maximum height (mm) (inches) 26.1 1.028 (mm) (inches) 101.6 4.000 +/- 0.010 (mm) (inches) 146.99 5.787 Maximum width Maximum length Max weight 40GB models 250, 200, 160, 120 and 80GB models 300 and 320 GB models 400 and 500GB models 2.6 525 grams (1.16 lbs) 580 grams (1.28 lbs) 655 grams (1.44 lbs) 710 grams (1.57 lbs) Seek time Seek measurements are taken with nominal power at 25°C ambient temperature.
2.8 Power specifications The drive receives DC power (+5V or +12V) through a four-pin standard drive power connector. 2.8.1 Power consumption Power requirements for the drives are listed in the table on page 25. Typical power measurements are based on an average of drives tested, under nominal conditions, using +5.0V and +12.0V input voltage at 25°C ambient temperature. • Spinup power Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed.
Table 9: DC power requirements (for 400GB and 500GB models) Power dissipation (watts) Avg (watts, 25° C) Avg 5V typ amps Avg 12V typ amps Spinup — — 2.90 (peak) Idle* 9.30 0.611 0.520 Idle* (with offline activity) 10.40 0.719 0.567 Operating (40% r/w, 40% seek, 20% inop.) 13.00 0.772 0.762 Seeking (random, 20% idle) 12.60 0.613 0.795 Standby 0.80 0.106 0.023 Sleep 0.80 0.106 0.
Table 13: DC power requirements (for 80GB and 40GB models) Power dissipation (watts) Avg (watts, 25° C) Avg 5V typ amps Avg 12V typ amps Spinup — — 2.80 (peak) Idle* 7.00 0.490 0.379 Idle* (with offline activity) 8.90 0.873 0.378 Operating (40% r/w, 40% seek, 20% inop.) 12.60 0.897 0.676 Seeking (random, 20% idle) 12.20 0.627 0.755 Standby 0.80 0.116 0.018 Sleep 0.80 0.116 0.018 *During periods of drive idle, some offline activity may occur according to the S.M.A.R.T.
2.8.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on the +12 volt line or an equivalent 15-ohm resistive load on the +5 volt line. • Using 12-volt power, the drive is expected to operate with a maximum of 120 mV peak-to-peak square-wave injected noise at up to 10 MHz. • Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave injected noise at up to 10 MHz. Note.
activity is required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the drive accepts all commands and returns to Active mode when disc access is necessary. 2.9 Environmental specifications 2.9.1 Ambient temperature Ambient temperature is defined as the temperature of the environment immediately surrounding the drive. Actual drive case temperature should not exceed 69°C (156°F) within the operating ambient conditions.
2.9.5 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis. 2.9.5.1 Operating shock These drives comply with the performance levels specified in this document when subjected to a maximum operating shock of 63 Gs based on half-sine shock pulses of 2 msec. Shocks should not be repeated more than two times per second. 2.9.5.
2.10 Acoustics Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All measurements are consistent with ISO document 7779. Sound power measurements are taken under essentially free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward. Note. For seek mode tests, the drive is placed in seek mode only. The number of seeks per second is defined by the following equation: (Number of seeks per second = 0.
2.
2.13 Agency certification 2.13.1 Safety certification The drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections of IEC950 and EN 60950 as tested by TUV North America. 2.13.2 Electromagnetic compatibility Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Electromagnetic Compatibility Directive (89/336/EEC).
2.13.3 FCC verification These drives are intended to be contained solely within a personal computer or similar enclosure (not attached as an external device). As such, each drive is considered to be a subassembly even when it is individually marketed to the customer. As a subassembly, no Federal Communications Commission verification or certification of the device is required.
2.15 Corrosive environment Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM B845. However, this accelerated testing cannot duplicate every potential application environment.
34 Barracuda 7200.9 PATA Product Manual, Rev.
3.0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3.1 Handling and static discharge precautions After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards.
3.2 Breather filter hole precautions This section contains information regarding the precautions which should be taken regarding the breather filter hole in Seagate hard disc drives. Proper precautions should be taken to ensure full functionality and prevent possible damage to the drive. Breather hole Do not cover or seal this hole. Figure 3 Breather filter hole location Caution: Do not cover, seal, or insert any object into this hole.
3.3 Jumper settings 3.3.1 Master/slave configuration The options jumper block shown in Figure 4 is used to configure the drive for operation. It is the 8-pin dual header between the interface connector and the power connector. Use the following settings to configure the drive as a master or a slave. Master or single drive. The drive is configured at the factory for a master or single-drive operation with a jumper set on pins 7 and 8. Drive as slave. Remove all jumpers.
3.3.4 Ultra ATA/100 cable An 80-conductor 40-pin cable is required to run Ultra DMA mode 3, mode 4, and mode 5. This cable uses even-numbered conductors connected to the ground pins to improve signal integrity. Master Pin 1 Co Mo mpu the ter rbo ard Slave Figure 5 Note. 3.4 Note. If you are using a 40-pin, 80-conductor cable, attach the blue connector to the motherboard, the black connector to the master drive, and the gray connector to the slave.
Notes: 1. Dimensions are shown in inches (mm). 2 Dimensions per SFF-8301 specification. 0.228 (5.79) 1.028 max (26.11) 2.83 (71.80) 3 x 0.25 0.010 (6.35 0.037) both sides 1.122 0.02 (28.5 0.51) 1.638 (41.61 0.01 0.25) 0.178 (4.27) 2.23 (56.56) 3.71 (94.35) 2 1.625 0.020 (41.28 0.51) 5.787 max (146.99) 1.75 0.01 (44.45 0.25) 4.0 0.01 (101.60 0.25) 4 x 6-32 UNC-2B 0.150 (3.81) max. fastener penetration. 3 threads minimum engagement.
40 Barracuda 7200.9 PATA Product Manual, Rev.
4.0 ATA interface These drives use the industry-standard ATA task file interface that supports 16-bit data transfers. It supports ATA programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–5. The drive also supports the use of the IORDY signal to provide reliable high-speed data transfers. You can use a daisy-chain cable to connect two drives to a single AT host bus.
4.1.1 Supported ATA commands The following table lists ATA-standard commands that the drive supports. For a detailed description of the ATA commands, refer to the Draft ATA-7 Standard. See “S.M.A.R.T. commands” on page 49 for details and subcommands used in the S.M.A.R.T. implementation.
Command name Command code (in hex) Security Erase Unit F4H Security Freeze F5H Security Set Password F1H Security Unlock F2H Seek 70H Set Features EFH Set Max Address F9H Note: Individual Set Max Address commands are identified by the value placed in the Set Max Features register as defined to the right. Address: Password: Lock: Unlock: Freeze Lock: Set Max Address Extended 37H Set Multiple Mode C6H Sleep 99H or E6H S.M.A.R.T. Disable Operations B0H / D9H S.M.A.R.T.
4.1.2 Identify Device command The Identify Device command (command code ECH) transfers information about the drive to the host following power up. The data is organized as a single 512-byte block of data, whose contents are shown in the Table 16 on page 42. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or vary with the state of the drive. See Section 2.0 on page 3 for default parameter settings.
Word Description Value 60–61 Total number of user-addressable LBA sectors available (see Section 2.2 for related information) *Note: The maximum value allowed in this field is: 0FFFFFFFh (268,435,455 sectors, 137 Gbytes). Drives with capacities over 137 Gbytes will have 0FFFFFFFh in this field and the actual number of useraddressable LBAs specified in words 100-103. This is required for drives that support the 48-bit addressing feature.
Word Description Value 100–103 Total number of user-addressable LBA sectors available (see Section 2.2 for related information). These words are required for drives that support the 48-bit addressing feature. Maximum value: 0000FFFFFFFFFFFFh.
12 Ultra DMA mode 4 is currently active. 13 Ultra DMA mode 5 is currently active. Bit Word 93 13 1 = 80-conductor cable detected, CBLID above VIH 0 = 40-conductor cable detected, CBLID below VIL Barracuda 7200.9 PATA Product Manual, Rev.
4.1.3 Set Features command This command controls the implementation of various features that the drive supports. When the drive receives this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an interrupt. If the value in the register does not represent a feature that the drive supports, the command is aborted. Power-on default has the read look-ahead and write caching features enabled.
4.1.4 S.M.A.R.T. commands S.M.A.R.T. provides near-term failure prediction for disc drives. When S.M.A.R.T. is enabled, the drive monitors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable. S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T.
50 Barracuda 7200.9 PATA Product Manual, Rev.
5.0 Seagate Technology support services Internet For information regarding Seagate products and services, visit www.seagate.com. Worldwide support is available 24 hours daily by email for your questions. Presales Support: Presales@Seagate.com Technical Support: DiscSupport@Seagate.com Warranty Support: http://www.seagate.com/support/service/index.html mySeagate my.seagate.com is the industry's first Web portal designed specifically for OEMs and distributors.
Customer Service Operations Warranty Service Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct customers should contact their Seagate Customer Service Operations (CSO) representative for warrantyrelated issues. Resellers or end users of drive products should contact their place of purchase or Seagate warranty service for assistance. Have your serial number and model or part number available.
Index A acoustics 29 Active mode 26 agency certification (regulatory) 31 alternate capacity jumper 37 altitude 27 ambient conditions 3 ambient temperature 22, 27 areal density 1, 21 ATA interface 41 ATA-standard commands 42 Australian C-Tick 32 autodetection 1 average seek time 22 B BIOS 37 BPI 21 breather filter hole precautions 36 buffer 21 burst 1 C cable 38 cable select 1 cable-select option 37 cache 1, 21 case temperature 27 CE mark 31 certification 31 Check Power Mode 42 commands 42 compliance 31 co
Identify Device command 44 Idle 42 Idle and Standby timers 26 Idle Immediate 42 Idle mode 26 Idle mode power 23 IEC950 31 Information Technology Equipment 31 Initialize Device Parameters 42 interface 21, 41 interface signals 41 interference 32 interleave 21 internal data-transfer rate OD 21 ISO document 7779 29 J jumper settings 37 K Korean RRL 31 L LBA mode 20 length 22 logical geometry 20 M maintenance 31 master 37 master/slave 1 Master/slave configuration 37 maximum temperature 27 measurement locatio
S.M.A.R.T. Enable/Disable Autosave 43 S.M.A.R.T. Execute Offline 43 S.M.A.R.T. Read Attribute Thresholds 43 S.M.A.R.T. Read Data 43 S.M.A.R.T. Read Log Sector 43 S.M.A.R.T. Return Status 43 S.M.A.R.T. Save Attribute Values 43 S.M.A.R.T.
56 Barracuda 7200.9 PATA Product Manual, Rev.
Seagate Technology LLC 920 Disc Drive, Scotts Valley, California 95066-4544, USA Publication Number: 100389997, Rev. F, Printed in U.S.A.
