User Manual
Table Of Contents
- Enterprise Capacity 3.5 HDD
- Seagate® Technology Support Services
- 1.0 Introduction
- 2.0 Drive specifications
- 2.1 Specification summary tables
- 2.2 Formatted capacity
- 2.3 Recording and interface technology
- 2.4 Start/stop times
- 2.5 Power specifications
- 2.6 Environmental limits
- 2.7 Acoustics
- 2.8 Test for Prominent Discrete Tones (PDTs)
- 2.9 Electromagnetic immunity
- 2.10 Reliability
- 2.11 Agency and Safety Certifications
- 2.12 Environmental protection
- 2.14 Corrosive environment
- 2.14 Reference documents
- 2.15 Product warranty
- 3.0 Configuring and mounting the drive
- 4.0 About self-encrypting drives
- 4.1 Data encryption
- 4.2 Controlled access
- 4.3 Random number generator (RNG)
- 4.4 Drive locking
- 4.5 Data bands
- 4.6 Cryptographic erase
- 4.7 Authenticated firmware download
- 4.8 Power requirements
- 4.9 Supported commands
- 4.10 RevertSP
- 4.11 ATA Security Erase Unit Command on SED SATA drives
- 4.12 Sanitize Device - CRYPTO SCRAMBLE EXT
- 5.0 About FIPS
- 6.0 Serial ATA (SATA) interface
Seagate Enterprise Capacity 3.5 HDD v5 Serial ATA Product Manual, Rev. E 7
2.0 Drive specifications
Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the
phrases the drive and this drive are used throughout this manual to indicate the following drive models:
2.1 Specification summary tables
The specifications listed in the following tables are for quick reference. For details on specification measurement or definition, see the
appropriate section of this manual.
Table 1 Drive specifications summary
5xxE models
Standard Standard Power Balance Self-Encrypting (SED) SED (FIPS 140-2)
ST6000NM0115 ST6000NM0215 ST6000NM0175 ST6000NM0275
ST4000NM0115 ST4000NM0245 ST4000NM0225
ST2000NM0125
4KN models
Standard Self-Encrypting (SED) SED (FIPS 140-2)
ST6000NM0125 ST6000NM0185 ST6000NM0265
ST4000NM0085 ST4000NM0055
ST2000NM0105
Drive specification
ST6000NM0115, ST6000NM0125,
ST6000NM0175, ST6000NM0185,
ST6000NM0215, ST6000NM0265,
ST6000NM0275
ST4000NM0055, ST4000NM0085,
ST4000NM0115, ST4000NM0225,
ST4000NM0245
ST2000NM0105,
ST2000NM0125
Formatted (512 bytes/sector)* 6TB 4TB 2TB
Guaranteed sectors (see Section 2.2)
Heads 10 7 4
Discs 5 4 2
Bytes per logical sector 512
Bytes per physical sector 4096
Recording density, KBPI (Kb/in max) 2018
Track density, KTPI (ktracks/in avg.) 369
Areal density, (Gb/in
2
avg) 732
Spindle speed (RPM) 7200
Internal data transfer rate (Mb/s max) 2396
Sustained data transfer rate OD (MiB/s max) 216 (226 MB/s max)
I/O data-transfer rate (MB/s max) 600
ATA data-transfer modes supported
PIO modes 0–4
Multiword DMA modes 0–2
Ultra DMA modes 0–6
Cache buffer 256MB (262,144KB) 128MB (129,536KB)
Weight: (maximum) 705g (1.55 lb) 680g (1.50 lb) 610g (1.34 lb)
Average latency 4.16ms
Power-on to ready (sec) (typ/max) 23/30
Standby to ready (sec) (typ/max) 23/30
Startup current (typical) 12V (peak)
2.6A
2.0A (optional configuration through Smart Command Transport)
Voltage tolerance (including noise)
5V +10/-5%
12V ±10%
Non-Operating ambient temperature (°C) –40 to 70
Operating ambient temperature (min °C) 5
Operating temperature (Drive case max °C) 60