Operating instructions

ManualsBrandsSe-Kure Controls ManualsAlerting SystemLE PLUS

Installation Instructions for the

ME Sr. III Alarm System

SK-210ME (Key Unit)

SK-210KME (Keypad Unit)

SK-295

AC/DC Power Supply

SKP-416K

Special Allen Key

SK-107ME

6 Port ME Splitter

SK-206ME

6 Port ME Strip Module

SK-212ME

12 Port ME Strip Module

Operation Guide

The ME Senior III Alarm Module is designed

to handle up to 12 terminals, (6 or 12 port

strips and 6 port splitter boxes in any combina-

tion), protecting up to 144 items. New micro-

processor technology enables the system to

identify the number of alarm sensors connected

to it, monitor battery level, and perform a con-

tinuous series of system-wide tests that look for

changes resulting from possible tampering.

Lighted LED Bar Graphs visually depict the

condition of batteries and AC power. When an

alarm occurs, it shows precisely which sensor

on which terminal caused the alarm.

The ME Alarm System utilizes the Se-Kure

Controls complete line of “LE” sensors.

Terminals:

Reading Time: 8 Minutes

SK-210KME

ME Sr. Keypad Alarm Module

Page 1

Install the AC/DC Adapter:

1. Plug the SK-295 AC/DC Adapter* into the

power supply jack on the back side of the alarm

module as shown in Fig. 1 at right.

Note: Always use a Se-Kure Controls (SK-295)

AC/DC Power Supply with Se-Kure alarms.

(Using a universal adapter could damage the

system and would void the warranty).

2. Plug the other end of the adapter into any

standard 110v wall outlet.

*International Users May Require a Special Adapter for 220v, (not supplied).

Fig.

SK-295

AC/DC Power Supply

Terminal Connection

(from ME Strip Alarm or ME Splitter Box)

Summary of content (11 pages)

PAGE 1
Installation Instructions for the SK-210ME (Key Unit) SK-210KME (Keypad Unit) ME Sr. III Alarm System Operation Guide The ME Senior III Alarm Module is designed to handle up to 12 terminals, (6 or 12 port strips and 6 port splitter boxes in any combination), protecting up to 144 items.
PAGE 2
Fig. 2 Battery Installation: 3. Insert and turn the key, then remove the Phillips Head Screw on the side of the alarm module to open the battery compartment as shown in the Fig. 2 at right. 4. Insert (6) “C” cell (alkaline) batteries into the battery tubes with the (+ -) polarity as indicated. 5. Replace the battery cover plate and the screw. Note: If the security screw is loose, or removed, when armed, the alarm will (((sound))).
PAGE 3
NOTE: Shunt plugs are not required and must not be used on ME terminals, when the ME system is activated, it will automatically detect and monitor all the open ports and sensored ports connected to it. SPECIAL NOTE: When a sensor is plugged into a strip or splitter port, the port light will turn GREEN. (If it is a “Dangling” or open or improperly connected sensor, the LED Light on the sensor will flash from RED to GREEN to RED . . . also, the Terminal and Bar Graph lights will flash).
PAGE 4
Sensor Connections: – (SK-953 Series Collar Lasso Sensor) Fig. 8 SK-953 Collar Lasso Sensor 15. The Collar Lasso Sensor has a wire connector that loops around the product and plugs back into itself using a telephone modular plug. 16. The Collar “Lasso” can be installed onto products by “Lassoing” any enclosed part of the product and plugging this module back into itself, (see Fig. 8).
PAGE 5
Arm the System: With all the Terminals, (Strips & Splitters), and Sensors attached: • Check to see there are no flashing LED Lights on Sensors. • Check to see there are no Lights lit on the Bar Graphs. If no lights are lit, proceed to step 17. If lights are still lit, proceed to steps 19 & 20. 17. Arm the system by entering your 4-digit code, or the factory preset code of: [*]1-2-3-4. (Keyed Units: Turn the key clockwise & remove). Disarm the System: 18.
PAGE 6
Installation Instructions for the ME Jr. plus 2 Alarm System SK-800KME Series ME Jr. Terminals SK-80108ME ME Jr. plus 2 (8) Port Strip SK-807ME ME Jr. plus 2 (8) Port Splitter Box Connects Alarm Module to Splitters & Strips & Splitters to Splitters SK-800KME ME Jr. plus 2 Alarm Module SK-3690 (Optional) “Where it’s At Light” SK-809 Telephone Modular “End Plug” SK-847-x Extension Fig. 1 Battery Installation: 1.
PAGE 7
Circuit “A” Light & Circuit “B” Light AC Power Light Will be lit if a Termination “End Plug” is not installed. Will )))flash((( if an alarm has been caused on that circuit. Will not be lit when all sensors and the Termination “End Plug” have been properly installed. Low Battery Light Will be lit when the SK-195 AC/DC Power Supply is supplying power to the Alarm Center. Will )))flash((( when batteries should be replaced. Will )))flash((( if no batteries are installed and the AC power is on.
PAGE 8
The “Where It’s At” LED Light: All ME Jr. Splitter Boxes and Strips are equipped with a “Where It’s At” light jack, for this optional accessory. When an alarm occurs, the light will )))flash((( to alert associates of the location of the alarm. Plug them in wherever needed, and adhere the light where it can be seen from a distance, (usually at the top of a display). Keypad Instructions: Features: A Keypad System has been added along with the mechanical key system to provide dual control.
PAGE 9
SK-800KME SK-800ME SK-800MEI ME Jr. plus 2 Alarm Module with Key Switch & Keypad ME Jr. plus 2 Alarm Module with Key Switch Only ME Jr. plus 2 Alarm Module with Key Switch & Infrared Remote Setting Up The Infrared Remote: 1. Open the battery compartment door to reveal the dip switches on the side of the SK-800MEI Alarm Module, as shown in Fig. 6. 2. Unscrew and open the SK-882 Infrared Remote. It is fastened together with a small phillips head screw, shown in Fig. 7. 3.
PAGE 10
Installation & Operation Instructions for the SK-T6 ALARM MODULE SK-T6 When installing batteries be sure to follow the POLARITY marked on the battery holder AC Power & Battery Installation: 1. Unlock the cover and open the lid. 2. Install (6) NEW “AA” Alkaline Batteries in the SK-T6 Alarm Module, onto the battery holder as shown at right. VERY IMPORTANT! When installing the batteries, follow the polarity indicated on the battery holder. 3. Close the lid. 4.
PAGE 11
Operating Instructions: 6. Turn the T6 Alarm Module Key to the “Stand-By” position. This is the position that you cannot remove the key. 7. Connect an LE sensor to the merchandise that is to be protected, follow the important cleaning step closely. VERY IMPORTANT! Clean the area on the product and the bottom of the sensor with Alcohol Prep Pads. While the alcohol is still wet, Wipe These Surfaces DRY with a clean paper towel.