User's Manual

Model: Vi-B72TH (Back)
Charging the Vi-B72TH
• Make sure your Bluetooth device and the Vi-B72TH are fully charged. Turn on
your Bluetooth device and turn on Bluetooth mode (check in Options or
Settings).
• Slide the ON/OFF/DEMO switch on the speaker to the ON position. Press and
hold the Bluetooth Pairing/Speakerphone/Music Button for 3 seconds.
The blue LED light will flash quickly, and a tone will sound as the speaker
enters pairing mode.
• “iHome B72 TH” should appear on your device. If “Not Connected” or similar
message appears, select “iHome B72 TH”” to connect. If your device asks for
a passcode, enter ‘1234’.
• Once paired, a confirmation tone will sound and the blue LED will glow solid.
You can then stream audio to the speaker.
• Control Bluetooth audio from your device. Remember to turn off the speaker
and your device after listening.
• If no device is paired within 3 minutes, a failure tone will sound, the blue light will
flash slowly and the unit will revert to standby mode. To retry pairing, press and
hold the Bluetooth Pairing/Speakerphone/Music Button for 3 seconds.
If pairing is not successful, turn the power “OFF” on the speaker and repeat
pairing procedure.
Using Bluetooth with the Vi-B72TH
Answer / End Calls
The Vi-B72TH also comes equipped with a Speakerphone function which will be
active when a call is coming through to your linked Bluetooth device. When an
incoming call is received on your device, briefly press the Bluetooth
Pairing/Speakerphone/Music Button on the speaker once to answer the call.
Press and hold for 2 seconds to reject the call. Speak into the microphone during
the call. To end the call, briefly press the Bluetooth Pairing/Speakerphone/Music
Button again.
Bluetooth Mode
Press and hold
for 3 seconds
to pair
to play
Bluetooth Pairing
Bluetooth Pairing/
Speakerphone/
Music
Front View
Back View
LED Charging/
Pairing Indicator
USB Charging Port
ON/OFF/DEMO Switch
Speaker
Microphone
Micro USB plug
Standard
USB plug
Charging cable
USB AC adaptor
connected to working outlet
Charging the V
i-B72TH
CHARGE UNIT BEFORE USE
OR
Computer
USB port
USB AC adaptor
(not included)
Computer
connected to
working outlet
The Vi-B72TH is powered by a rechargeable battery in the speaker.
Make sure to
charge speaker before use, using the supplied USB cable.
• Connect the micro-USB plug to the Charging jack on the speaker.
• Connect the standard USB plug to a powered USB port, such as that on a
computer. Your computer should be connected to a wall outlet when the
speaker is charging. The light on the speaker will turn to solid red while
charging and turn off when fully charged.
• When the battery is low, the red LED will begin to flash. If you start to notice
sound distortion at higher volumes, it's time to recharge the batteries.
NOTE: The charging LED light will override the pairing LED light pattern.
• Place the unit on a level surface away from sources of direct sunlight or excessive
heat.
• Protect your furniture when placing your unit on a natural wood and lacquered
finish. A cloth or other protective material should be placed between it and the
furniture.
• Clean your unit with a soft cloth moistened only with mild soap and water. Stronger
cleaning agents such as thinner or similar materials can damage the surface of
the unit.
Maintenance
The Vi-B72THHHHHHHHH HH is equipped with an ON/OFF/DEMO Switch. DEMO
Getting Started
mode is for in-store demonstration only. When you are ready to
use the speaker, slide the switch to ON mode.
DC 5V,
500mA
ON OFF DEMO
DC 5V,
500mA
ON OFF DEMO
Touch
Sensor
Note: When the unit is in OFF
mode, gently press the Touch
Sensor OR the Bluetooth Pairing/-
Speakerphone/Music Button to
play built-in music.
If no music is streaming in
ON mode, the unit will
automatically time out
after 5 minutes to save
battery life. To wake,
gently press the Touch
Sensor.
H