User's Manual

Model: iZBT10
Instruction manual - US English
Size: 102 x 150 mm
Date: July 6, 2016
Mat’l: 100gsm paper (WF)
Color: Black text on white background
10
SETTING AND USING THE SLEEP
TIMERS (Continued)
Press the Sleep Button during sleep to set sleep to review sleep time
remaining. Press again to go to next (lower) sleep duration. During sleep
mode, any current light therapy sound levels and/or light therapy brightness
levels will gradually be lowered to o.
After setting the sleep timer, your settings will be saved for later use. At any
time simply press the Sleep button to enter directly into that sleep preset.
* Note: the unit will silence the audio but will NOT turn o your Aux device.
BLUETOOTH
PAIRING
Pairing establishes a unique communication connection between the unit
and your Bluetooth device. Once paired, you will be able to stream audio
wirelessly to the iZBT10 and control features using the iHome Zenergy™ app.
1. Turn on your Bluetooth device and make it
“discoverable” by turning on Bluetooth mode
(check in Options or Settings).
2. Press and release the Power Button to turn
on the iZBT10 in Bluetooth (PHONE) mode. The
first time the unit is turned on it will enter auto
pairing mode: voice prompts will announce
“pairing” and PAIR and the BT icon will flash on
the display while the unit attempts to pair.
“iHome iZBT10” should appear on your device’s
menu. Select “iHome iZBT10” on device to
begin/complete pairing. If your device asks for a
password, enter 1234 on the keyboard of your
device. A voice prompt will announce “Bluetooth
connected”. If no device is paired within 3
minutes, the unit will revert to its previous state.
(Continued on page 11)
iHome iZBT10
SETTING AND USING THE SLEEP
TIMERS
You can easily set your sleep timer presets using the iHome Zenergy™ app.
SETTING THE SLEEP TIMER FROM THE UNIT
Sleep mode lets you sleep to built-in lights, sounds, your Bluetooth device,
FM radio or Aux-in for the set sleep duration, then turns the unit o. There
are two sleep modes, Sleep 1 and Sleep 2, each set the same way.
Directions below show Sleep 1 Button. Use Sleep 2 Button to set Sleep 2
mode. Press the sleep button to go straight into sleep time setting with
current settings. Otherwise follow steps below.
Unit must be powered on for sleep mode.
1. Press and hold the Sleep 1 Button or 3 seconds. The current Sleep
1 audio source and “ZZZ” will flash in the display. Press the
+ or – Buttons to select the desired sleep audio source: SOUNDS,
PHONE (Bluetooth), RADIO, AUX-IN* or NONE (no sleep audio).
2. Press the Sleep 1 Button to confirm sleep audio source.
a. If Sounds or Radio was selected, the current sound or radio
frequency will flash. Press the + or – Buttons to select the desired
sound or radio station.
b. If None was selected, the current Light mode will appear. Press the
+ or – Buttons to select the desired light mode.
c. If Phone or Aux-in was selected, the current sleep volume will
appear. Press the + or – Buttons to select the desired sleep volume.
3. Press the Sleep 1 Button to confirm and advance to volume
setting, light mode or light brightness setting, depending on
previous audio selection. Press the + or – Buttons to select
the desired setting.
4. Press the Sleep 1 Button to confirm and advance, then press
the + or – Buttons to select the desired setting.
5. Continue in this manner until ”120” appears on the display. Press the
Sleep 1 Button as needed to cycle to the desired sleep duration:
120, 90, 60, 30, 15 minutes or OFF (turns unit o). When the
desired sleep duration is displayed, allow Sleep 1 setting to time
out (do not press any buttons for about 10 seconds). Your sleep
timer will be active upon exiting.
(Continued on page 10)