VEHICLE SECURITY SYSTEM G25/G20
Limited Lifetime Warranty This vehicle security system is warranted to the original purchaser, to be free from defects in material and workmanship. The manufacturer will repair or replace at its option, and free of charge for the first twelve (12) months, any part that proves defective in material or workmanship under normal installation, use, and service, provided the product is returned to the manufacturer freight prepaid.
Remote Transmitters Remote Transmitter Description LED LED Button 1 Button 2 Button 1 Button 2 Button 3 Button 4 Button 3 Button 4 Button 5 The G25/G20 Security System is supplied with two 5/4-button Remote Transmitters used to control system operations. Button 1 Arms the system and when held for 2 seconds, activates the system’s Panic feature. Button 1 also locks the doors when the system is in Valet Mode. Button 2 Disarms the system.
Tamper Alert If the system was triggered while away, the LED will flash to indicate which zone triggered the system after disarming and turning on the ignition. The LED indication will repeat 8 times.
System Operation Remote Arming The system monitors 3 independent areas (zones) while armed: doors, hood/trunk, and shock sensor input. To Arm the System: 1. Turn off the ignition. 2. Press Button 1. · The siren will chirp once.* · The doors will lock. · The parking lights will flash once. · The LED will turn On, to indicate the starter defeat is activated. 3. 5 seconds after Arming: · The LED will start blinking to indicate that the doors and hood/trunk inputs are being monitored.
1. Turn off the ignition. 2. Open the door and exit the vehicle. · Once all doors are closed and the dome light is off, the LED will begin flashing rapidly. 3. After 30 seconds, · The siren will chirp. · The parking lights will flash. · The doors will lock.* · The status LED will begin flashing. 4. The system is now armed. * If the Passive Locking feature is selected. If the Passive Arming with Countdown feature is programmed, the siren will chirp every 2 seconds until the system passively arms.
10 seconds on the last press. · The system will disarm. If the code is entered incorrectly, turn off the ignition and begin again. To set the Emergency Override Code: 1. Turn on ignition. 2. Within 5 seconds, press the valet switch 5 times. · The siren will provide one long chirp, indicating that you have entered Programming. 3. Press the valet switch 3 times. · The siren will chirp each time the valet switch is pressed. 4. Within 5 seconds, press Button 3 on the transmitter. · The siren will chirp 3 times.
Extended Features Ignition Controlled Door Locks For added safety, the Ignition Door Locking feature allows vehicles equipped with power door lock systems to automatically lock the doors when the ignition is turned on, and unlock the doors after the ignition key is turned off. If a door is open when the ignition is turned on, the ignition locking feature is disabled to protect against locking the keys inside the vehicle.
System Programming Entering System Programming To enter System Programming: 1. Turn on ignition. 2. Within 5 seconds, press the valet switch 5 times. · The siren will provide one long chirp, indicating that you have entered Programming. 3. Press the valet switch the number of times equal to the System Parameter you want to change. · The siren will chirp each time the valet switch is pressed. 4.
1. Horn Chirps with Arm & Disarm. Selects one of three modes: Normal, Horn Chirps, and Horn Chirps w/Warn. Normal. When selected, the horn will honk only when the alarm is triggered. Horn Chirps. When selected, the horn will provide the arm/disarm and trigger indications, allowing the siren installation to be skipped. Horn Chirps w/Warn. When selected, the horn will provide arm/disarm, trigger, and warn-away indications. 2. Arm Mode.
Door Lock Diagrams Negative Trigger Adding Actuators Reverse Polarity Positive Trigger blue green Starter Interrupt Page 10 - G25/G20 Positive Horn Honk
Wiring Diagram Shock Sensor Green - Lock Out (-) 500mA Blue - Unlock Out (-) 500mA Valet Switch LED Blue Red Control Unit G25/G20 Orange - Ground when Armed Output (-) 500mA Blue - Hood/Trunk Trigger Input (-) Black/White -Domelight/ Aux.
