GALAXY G40RS AUTOMATIC TRANSMISSION WITH SEPERATE LOCK/UNLOCK BUTTONS REMOTE START SYSTEM PRODUCT MANUAL
Limited Lifetime Warranty This vehicle remote start system is warranted to the original purchaser, to be free from defects in material and workmanship. The manufacturer will repair or replace at its option, and free of charge for the first twelve (12) months, any part that proves defective in material or workmanship under normal installation, use, and service, provided the product is returned to the manufacturer freight prepaid.
Remote Transmitters Remote Transmitter Description LED Button 1 Button 3 Button 2 Button 4 The G40RS is a state-of-the-art remote starting system is supplied with two 4-button Remote Transmitters used to control system operations. The built-in remote start feature is designed to offer maximum convenience by remote starting your vehicle’s engine, turning on the heater/air conditioner, and then running for a pre-determined time to provide a comfortable environment once you enter your vehicle.
Adding/Replacing Transmitters To replace lost or stolen transmitters or to add additional transmitters into the system, have all desired transmitters ready and follow the steps below. Note: Up to four transmitters can be programmed to operate the system. To erase any previously stored transmitter codes, be sure to program all 4 transmitter memory locations. To program transmitter(s): 1. Turn the ignition key On, Off, On, Off, and back On. · The parking lights will flash 3 times. 2.
System Operation Remote Locking To Lock the doors: 1. Turn off the ignition. 2. Press Button 1. · The doors will lock. · The parking lights will flash once. · The LED will turn on, to indicate the doors are locked. 3. 10 seconds after Locking: · The LED will start blinking. Remote Unlocking To Unlock the doors: Press Button 2. · The doors will unlock. · The parking lights will flash twice. · The LED will turn off . Remote Starting Automatic Transmission Mode To Remote Start the System: 1.
Valet Mode The Valet Mode temporarily disables the remote start system so the vehicle may be serviced by a mechanic. The remote transmitters will continue to lock/unlock the doors. To activate or deactivate the Valet Mode: 1. Turn on the ignition. 2. Press and hold the override switch for 5 seconds. · The parking lights will flash once and LED will be On to confirm the Valet Mode is on or twice and LED will turn off to confirm Valet Mode is off. 3. Turn off the ignition.
Ignition Door Locking For added safety, the Ignition Door Locking feature allows vehicles equipped with power door lock systems to automatically lock the doors when the ignition is turned on. Ignition Door Unlocking For added convenience, this feature automatically unlocks the doors after the ignition key is turned off. The Ignition Door Unlocking feature may also be completely disabled if desired.
System Programming Branch Feature 1. Ignition Door Locking 2. Ignition Door Unlocking 3. Door Unlock Pulse 4. Door Lock Pulse Length 5. Lock after Start 6. Lock after Shutdown 7. Engine Run Time 8. Automatic Start Mode 9. Tachless Sense Crank Time 10. Engine Type 11. Ignition 2 Output Program 12. Unlock Before Start 13. Horn Chirp 14.
System Installation 8-Pin Main Harness Pin 1 RED WIRE: Module Power Input (+). Connect to a constant source of +12V Pin 2 GREEN/WHITE WIRE: Brake Input (+). Connect to the wire that shows +12V when pressing the brake. The Green/white wire is a safety shutdown wire that must be connected. Pin 3 BROWN/WHITE: Horn Output (-) 500 mA. Connect to a relay to activate the vehicle’s horn when the alarm is triggered.
3-Pin White Door Lock Connector: Door lock port. 2-Pin Blue Connector: Valet switch port. Mount switch where it is accessible from the driver’s position. 2-Pin Red Connector: LED port. Mount LED where it may be easily seen from either side of the vehicle. 3-Pin White Door Lock Connector: Door lock port. · BLUE WIRE - negative unlock output (-) 500mA. · RED WIRE - (+) 100mA trigger output for optional plug-in door lock relay module, · GREEN WIRE - negative lock output (-) 500mA.
Door Lock Diagrams Negative Trigger Adding Actuators Reverse Polarity Positive Trigger blue green Positive Horn Honk Page 10 - G 40RS
Wiring Diagram Violet Yellow Orange Brown Red Red Red Green/White Brown/White White White/Black Blue/Orange Black Black/Gray Control Unit G-40RS Starter Output Ignition 1 Output Accessory Output Ignition 2 Output +12V Battery Input #1 25 Amp. +12V Battery Input #2 25 Amp. +12V Battery Input #3 Brake Input(+) Horn Output (-)500mA Parking Light 1 Output (+/- built-in relay) Hood/Trunk Input (-) Remote Start Output (-)500mA Ground Tachometer Input Green Lock output (-) 500mA. Blue Unlock output (-) 500mA.
