2100RS SERIES REMOTE START SYSTEM PRODUCT MANUAL
Limited Lifetime Warranty This vehicle remote start system is warranted to the original purchaser, to be free from defects in material and workmanship. The manufacturer will repair or replace at its option, and free of charge for the first twelve (12) months, any part that proves defective in material or workmanship under normal installation, use, and service, provided the product is returned to the manufacturer freight prepaid.
Table of Contents 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. About Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 1 Remote Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2 Remote Transmitter Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2 Adding/Replacing Transmitters . . . . . . . . . . . . . . . . . . . .
About Your System The ScyTek Galaxy Starter is a start-of-the-art remote starting system featuring a built-in "ScyNet Network Port" that allows direct connection of optional accessory modules and a PC interface offering expanded system operation. With proper installation this system will provide superior protection and performance for many years to come.
Remote Transmitters Standard Remote Transmitter Description LED Button 1 Button 3 Button 2 Button 4 9 Button 5 The Galaxy 5100RS Plus is compatible with the optional 5-button Remote Transmitters used to control system operations. Note: Using the optional PC or Pocket PC interface with the network software, it is possible to reconfigure the functionality of the transmitter buttons. The standard (default) setting for operation of the transmitters is described below.
Adding/Replacing Transmitters To replace lost or stolen transmitters or to add additional transmitters into the system, have all desired transmitters ready and follow the steps below. Note: Up to 4 transmitters can be programmed to operate the system. To erase any previously stored transmitter codes, be sure to program all 4 transmitter memory locations. To program the transmitter(s): 1. Turn on the ignition key On, Off, On, Off, and back On. · The parking lights will flash 3 times. 2.
True Color 2-way LCD Remote Transmitter Description Button 1 Button 2 Button 3 Button 4 The Galaxy 5100RS-TC is compatible with the True Color 2-way LCD remote transmitter, offering increased range and confirmation of any activated features. Button 1 Arms the system. Button 1 also locks the doors when the system is in Valet Mode. Button 2 Disarms the system. Button 2 also unlocks the doors when the system is in Valet Mode. Button 3 When Pressed and released momentarily activates the Auxiliary Output 2.
4. Turn off the ignition key. 5. Repeat steps 1-4 to add an additional 2-way transmitter. LCD Transmitter Battery Replacement Your Galaxy Remote Transmitter uses a 1.5 volt AAA alkaline battery, which will require replacement in time. Depending on the amount of use, the battery may last up to six months before it needs replacement.
LCD Backlight Transmitter Button 4 is used for confirmation, transmitter programming, as well as activation of the LCD backlighting for use in the dark. Press button 4 momentarily to activate the LCD backlight. System Confirmation The 2-way transmitter's confirmation feature allows the current vehicle status to be displayed at any time. To display system status: Press and hold Button 4 until the display shows CON. · The transmitter will beep once.
Galaxy 2100RS Plus - Page 7
System Operation Remote Locking To Lock the doors: 1. Turn off the ignition. 2. Press Button 1. · The audible status output will beep (if connected) · The doors will lock. · The parking lights will flash once. · The LED will turn on red, to indicate the doors are locked. 3. 10 seconds after Locking: · The LED will start blinking as a theft deterrent. Remote Unlocking To Unlock the doors: Press Button 1. · The audible status output will beep (if connected) · The doors will unlock.
Remote Start Features Remote Starting To Remote Start the System: 1. Be sure the system is not in Valet Mode. 2. Press and hold Button 4 for three seconds. · The parking lights will turn on. · The LED will flash rapidly. · The engine will start and run for the duration of its programmed Run Time.* · The heater or air conditioner will turn on (if turned on prior to exiting the vehicle). *If the engine fails to start on the first attempt, it will repeat the starting procedure 2 more times.
Automatic Start Mode The Automatic Start Mode allows the vehicle to automatically start the vehicle every one or two hours and run for the preset Run Time. To turn on Auto Cold Starting: 1. Turn Ignition switch Off and wait for 3 seconds. 2. Turn Ignition switch On and Off three times ending with Ignition in Off position 3. Press the Valet switch within three seconds Side lights will flash indicating that the Cold Start mode has been activated.
Extended Features Ignition Door Locking For added safety, the Ignition Door Locking feature allows vehicles equipped with power door lock systems to automatically lock the doors when the ignition is turned on. If a door is open when the ignition is turned on, the Ignition Door Locking feature is disabled to protect against locking the keys inside the vehicle. Ignition Door Unlocking For added convenience, this feature automatically unlocks the doors after the ignition key is turned off.
System Installation 1. 2. Thoroughly read and become familiar with the installation instructions before beginning the installation. Review system contents: Main Unit Two 5-Button Remote Transmitters Harnesses • 6-Pin starter harness • 20-Pin main harness • 4-Pin auxiliary start harness • 3-Pin door lock harness • LED harness • Override Switch harness 3. 4. Verify vehicle is equipped with electronic fuel injection, and starts/idles normally before installation.
System Wiring 6-Pin Starter Harness Pin 1 RED WIRE A: Main Power Input A (+). Connect to the battery or constant power wire at the ignition switch with a minimum 25 Amp supply. Remove fuse until installation is complete and wiring is checked. Pin 2 RED WIRE B: Main Power Input B (+). Connect to the battery or constant power wire at the ignition switch with a minimum 25 Amp supply.
Pin 13 WHITE/BLACK WIRE: Hood Pin Input (-). Connect the to the hood pin switch. The switch must provide a ground output when switch is opened. Pin 14 ORANGE WIRE: Anti-Grind Output (-) 500 mA. The Orange wire provides a ground output to activate a relay for anti-grind protection. Pin 15 VIOLET/WHITE WIRE: Factory Disarm Output (-) 500 mA. The Violet/white wire provides a ground output on disarming and before remote starting to disarm a factory security system.
Jumper Settings Jumper Selection Carefully separate the top and bottom halves of the main unit case. Once the cover is removed, the parking light polarity jumper will be visible next to the parking light relay. Set the jumper for the correct polarity output as described below, then reassembly the main unit case. Parking Light Output. Selects the polarity (+/-) for the output of the on-board Parking Light relay.
System Programming Entering System Programming Although this system is compatible with the optional FM transmitter, all programming is performed using the standard AM transmitter unless otherwise noted. To enter System Programming: 1. Turn on ignition. 2. Within 5 seconds, press the valet switch 5 times. · The parking lights will provide three blinks, indicating that you have entered Programming. 3. Press the valet switch the number times equal to the System Parameter you want to change.
Branch Feature 1. Ignition Door Locking 2. Ignition Door Unlocking 3. Door Unlock Pulse 4. Door Lock Pulse Length 5. Aux 2 Activate on Lock 6. Aux 1 Mode 7. Aux 2 Mode 8. Unlock with Aux 1 9. Start in Valet Mode 10. Lock after Start 11. Lock after Shutdown 12. Engine Run Time 13. Automatic Start Mode 14. Engine Sense Mode 15. Remote Start Program 16. Ignition 2 Output Program 17. Horn Honk Output 18. Turbo Mode 19.
13. Automatic Start Mode. Selects between every two hours or every hour for the automatic engine starting feature. 14. Engine Sense Mode. Selects between Tachless and Tach Monitor operation. Tachless. Determines the engine status using an advanced software routine, without requiring connection to the vehicle’s tachometer. Tachless operation may not be compatible with some vehicles or in severe temperatures, in which case the tach wire must be connected. Tach Monitor.
Wiring Diagrams Positive Dome Negative Dome Positive Horn Negative Horn Negative Glow Plug Starter Anti-Grind Galaxy 2100RS - Page 19
Door Lock Diagrams Follow the diagrams below for connecting basic door lock systems. For Two Stage door lock systems (separately unlocks driver and passenger doors) see following pages.
Two Stage Door Lock Diagrams The Galaxy Starter is equipped with a dedicated Passenger Unlock output allowing Two Stage Door Lock operation. When connected as shown below, unlocking the system will unlock only the driver’s door. Pressing the unlock button again will unlock all doors.
Two Stage Door Lock Diagrams cont’d Two Stage Reverse Polarity Two Stage Adding Actuator Page 22 - Galaxy 2100RS
Technical Information FCC ID: OARRXAM2000 This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference.
GALAXY 2100RS ScyNet Port Emergency brake(-) Start (-) Green Blue Antenna Wiring Diagram Not Available External Activation ScyTek Electronics 11627 Cantara Street Unit B North Hollywood, CA 91605 © ScyTek Electronics 2005 Galaxy Starter r2 2/24/05
