G777,G27 A777,A20 VEHICLE SECURITY SYSTEM PRODUCT MANUAL
Limited Lifetime Warranty This vehicle security system is warranted to the original purchaser, to be free from defects in material and workmanship. The manufacturer will repair or replace at its option, and free of charge for the first twelve (12) months, any part that proves defective in material or workmanship under normal installation, use, and service, provided the product is returned to the manufacturer freight prepaid.
2-way LCD Remote Transmitter Description Button 1 Button 2 Button 3 Button 4 Button 5 Page 1 Button 1 Arms and Locks the system and when held for 5 seconds, activates the system’s Panic feature. Button 1 also locks the doors when the system is in Valet Mode. Button 2 Disarms and Unlocks the system. Pressing Button 2 again operates the Passenger Unlock feature (if installed). Button 2 also unlocks the doors when the system is in Valet Mode.
Remote Transmitters Remote Transmitter Description LED Button 1 Button 2 LED Button 1 Button 2 Button 4 Button 3 Button 5 Button 4 Button 3 G777,G27 Button 5 A777,A20 The G777,G27,A777,A20 is supplied with 5-button Remote Transmitter used to control system operations. Button 1 Arms and Locks* the system and when held for 5 seconds, activates the system’s Panic feature. Button 1 also locks the doors when the system is in Valet Mode. Button 2 Disarms and Unlocks* the system.
Adding/Replacing One-Way Transmitters To replace lost or stolen transmitters or to add additional transmitters into the system, have all desired transmitters ready and follow the steps below. Note: Up to 4 one-way transmitters can be programmed to operate the system. Any previously stored transmitter code will be erased if it is not programed within the following sequence. To program the transmitter(s): 1. Turn on the ignition key On, Off, On, Off, and back On. · The siren will chirp 3 times. 2.
System Operation Remote Arming The system monitors 4 independent areas (zones) while armed: doors, hood/trunk, shock sensor and optional sensor input. To Arm the System: 1. Turn off the ignition. 2. Press Button 1. · The siren will chirp once.* · The doors will lock. · The parking lights will flash once. · The LED will turn on, to indicate the starter defeat is activated. 3. 5 seconds after Arming: · The LED will start blinking to indicate that the doors and hood/trunk inputs are being monitored.
Tamper Alert If the system was triggered while away, the LED will flash to indicate which zone triggered the system after disarming and turning on the ignition. The LED indication will repeat 8 times.
Panic Mode In the event of an emergency, the transmitter’s remote Panic feature can be used to instantly trigger the alarm. To activate the Panic Mode: 1. Press and hold Button 1 for 5 seconds. · The alarm will sound. · The parking lights will flash. · The doors will unlock* allowing access to the vehicle. 2. Press Button 2 to stop Panic Mode. * If the ignition is on when the Panic feature is activated, the doors will lock for personal safety.
System Programming Entering System Programming To enter System Programming: 1. Turn on ignition. 2. Within 5 seconds, press the valet switch 5 times. · The siren will provide three chirps, indicating that you have entered Programming. 3. Press the valet switch the number times equal to the System Option you want to change. · The siren will chirp each time the valet switch is pressed. 4. Within 5 seconds, press the transmitter button corresponding to the desired operating mode for that System Option.
6. Ignore Open Door Report. Bypasses the open zone warning chirps for vehicles equipped with a residual dome light circuit that remains ON for a period of time after closing the door. 7. Auto Rearming Mode. When selected, the system will automatically re-arm and lock 30 seconds after it has been disarmed regardless if a door is open or closed. 8. Door Unlock Pulse. Selects between one pulse or two pulse operation for the door unlock output.
20. Data Bus Input Triggers. When enabled, the system will read all available triggers from the bypass module. If disabled the system triggers must be hardwired. 21. Data Bus Interface Mode. Selects between iData, Fortin, or Fortin RF kit bypass modules. 22. Starter Confirmation Chirps. When enabled system chirps before remote stater activated, when disabled, no chirps will sound upon remote start. 23. Lock After Start. this dual program branch selects lock after start, and enables push to start.
Programming Branch Table Branch 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Feature Horn Chirps w/ Arm&Disarm Arm Mode Passive Door Locking Ignition Controlled Locks Ignition Controlled Unlock Ignore Open Door Report Auto Rearming Door Unlock Pulse Warnaway Report Disarm with Aux 1 Door Lock Pulse Length Anti-Carjack Type Anti-Carjack Mode Horn Honk Chirp Aux 2 Activate on Arm Aux 1 Mode Aux 2 Mode Aux 2 Type Extended Parking Lights Databus Input Triggers Data Bus
Door Lock Diagrams Follow the diagrams below for connecting basic door lock systems. For Two Stage door lock systems (separately unlocks driver and passenger doors) see following pages.
Technical Information FCC ID: OARRXAM2000 This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference.
Upgrade Options 2WC-KIT Two Way Pager upgrade kit Easy Plug and Play upgrade to a complete two way system. Increases range MobiLink 100 Smart phone upgrade Easy Plug and Play upgrade through the system- Antenna port 2 Way confirmation Arm/Disarm Remote Start On/Off Trunk Release Alert Notification MobiLink GPS GPS upgrade Works with MobiLink 100 Easy Plug and Play GPS Tracking upgrade.
Wiring Diagram Shock Sensor, zone 2 Valet Switch LED SCYTEK SECURITY MODULE Green Red Blue Lock Output (-) 500mA Empty Unlock Output (-) 500mA Red (+) Constant Power Input White (+)/(-) Selectable Light Flash Output Brown (+) 2A Siren output Blue/White (-) 500 mA Passenger Unlock Out (-) White/Red (-) 500mA Channel 2 Output Orange (-) 500 mA Armed Outpu Brown/White (-) 500 mA Horn Output Black/White (-) 500mA Dome Light Out Blue (-) Hood/Trunk Trigger Input, zone 5 Gray (-) 500mA Channel 1 Output,Trunk
