G5.2W, G2.2W A4.2W, A1.2W A1.
Limited Lifetime Warranty This vehicle security system is warranted to the original purchaser, to be free from defects in material and workmanship. The manufacturer will repair or replace at its option, and free of charge for the first twelve (12) months, any part that proves defective in material or workmanship under normal installation, use, and service, provided the product is returned to the manufacturer freight prepaid.
Table of Contents 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. About Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 1 Remote Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2 Remote Transmitter Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 3 Adding/Replacing Transmitters . . . . . .
Upgrade Options 2WC-KIT Two Way Pager upgrade kit Easy Plug and Play upgrade to a complete two way system. Increases range MobiLink 100 Smart phone upgrade Easy Plug and Play upgrade through the system- Antenna port 2 Way confirmation Arm/Disarm Remote Start On/Off Trunk Release Alert Notification MobiLink GPS GPS upgrade Works with MobiLink 100 Easy Plug and Play GPS Tracking upgrade.
About Your System G5, A4 Series is a Combination Vehicle Security and Remote Starting System , G2, A1 Series is a Remote Starting with keyless entry. With proper installation this system will provide superior protection and performance for many years to come.
Remote Transmitters Standard Remote Transmitter Description LED Button 1 Button 2 LED Button 1 Button 2 Button 4 Button 3 Button 5 Button 4 Button 3 G Series Remote Button 5 A Series Remote Remote Button 1 Arms and Locks the system and when held for 5 seconds, activates the system’s Panic feature. Button 1 also locks the doors when the system is in Valet Mode. Button 2 Disarms and Unlocks the system. Pressing Button 2 again operates the Passenger Unlock feature (if installed).
One Button Remote Transmitter A1.1 Series Remote Program transmitter(s): 1. Turn on the ignition key On, Off, 4 times and then back On on fifth time. · The siren will chirp 5 times. 2. Press and hold the Override switch for 5 seconds. · The siren will chirp 5 times. · The LED will illuminate. 3. Press Button on the first transmitter. · The siren will chirp once. 4. Repeat step 3 for each transmitter (up to 4). 5. Turn off the ignition key.
Adding/Replacing Standard Remote Transmitters To replace lost or stolen transmitters or to add additional transmitters into the system, have all desired transmitters ready and follow the steps below. Note: Up to 4 one-way transmitters can be programmed to operate the system. Any previously stored transmitter will be erased if it is not programed within the following sequence To program the transmitter(s): 1. Turn the ignition key On, Off, On, Off, and back On.
2-way LCD Remote Transmitter Description Button 1 Button 2 Button 3 Button 4 Button 5 Page 1 Button 1 Arms and Locks the system and when held for 3 seconds, activates the system’s Panic feature. Button 1 also locks the doors when the system is in Valet Mode. Button 2 Disarms and Unlocks the system. Pressing Button 2 again operates the Passenger Unlock feature (if installed). Button 2 also unlocks the doors when the system is in Valet Mode.
Setting The Time The LCD display is equipped with a 12-hour clock Set the time: 1. Press and hold Buttons 2 and 3 for three seconds. · The remote will beep two times and three bars will be shown indicating time set mode is entered. 2. Press and release Button 2 until the correct hour is displayed. (hold button to scroll). 3. Press and release Button 3 until the desired minute is displayed. (hold button to scroll). 4. When the desired time is displayed, press Button 5 to store.
Automatic Cold Start Temperature Setting (2 step procedure, for second step see page 7 under “C st”) The Automatic Cold Start setting sets the temperature threshold. If automatic start is set to cold temperature setting,the starter will activate every 2 or 4 hours if the temperature drops bellow the set value. (LED will flash slow in this mode) 1. Press and hold Buttons 2 and 3 until the remote beeps five times. · “cold” is shown indicating automatic cold start temperature set mode is entered. 2.
AUTO display starter autostart enabled features. 1. Press and hold Button 5 until the display shows AUTO. ·The transmitter will beep three times. 2. Release Button 5. · The LCD panel will display what starter auto start features are enabled. SPCL Program the pager time of a day clock from the internal Remote Starter clock, the remoter starter sends its time to the pager. 1. Press and hold Button 5 until the display shows SPCL. ·The transmitter will beep four times. 2. Release Button 5.
Pager Icon Description Battery Status Valet Starter Status Chirp Disable Timer Start Enabled Alarm Clock Daily Start Enabled Temperature Start Enabled Lock/Unlock Status Vibration Sensor Triggered Hood Sensor Triggered Trunk Sensor Triggered Vibraton On/Sound Off Sound On/Vibration Off Transmit G5.2W, G2.2W, A4.2W, A1.
System Operation Remote Arming/Locking The system monitors 5 independent areas (zones) while armed: doors, hood/ trunk, shock sensor, optional sensor input. To Arm and Lock the System: 1. Turn off the ignition. 2. Press Button 1. · The siren/horn will chirp/honk once. · The doors will lock. · The parking lights will flash once. · The LED will turn ON, to indicate the starter defeat is activated. 3.
Tamper Alert If the system was triggered while away, the LED will flash to indicate which zone triggered the system after disarming and turning the ignition ON. The LED indication will repeat 8 times.
Panic Mode In the event of an emergency, the transmitter’s remote Panic feature can be used to instantly trigger the alarm/panic feature. To activate the Panic Mode: 1. Press and hold Button 1 for three seconds. · The alarm will sound. · The parking lights and horn will flash. · The doors will unlock** allowing access to the vehicle. 2. Press Button 1 or 2 to stop Panic Mode. ** If the ignition is on when the Panic feature is activated, the doors will lock for personal safety.
· The siren will chirp each time the valet switch is pressed. 4. Within 5 seconds, press Button 3 on the transmitter. · The siren will chirp 3 times. 5. Press the valet switch the number of times equal to the desired code (from 1-15). 6. Turn off the ignition then arm the system. 7. Disarm the system using the new Override Code to permanently store the new code. Note: If the code set procedure is not properly performed, turn off the ignition and begin again.
Remote Start Features Remote Starting To Remote Start the System: 1. Be sure the system is not in Valet Mode. 2. Press and hold Button 4 for three seconds. · The parking lights will flash 4 times and turn on. · The siren/horn will chirp/honk 4 times. ( if enabled, see page 24 branch 9 ) · The engine will start and run for the duration of its programmed Run Time.** · The heater or air conditioner will turn on (if turned on prior to exiting the vehicle).
Automatic Start Mode Automatic Start feature has three modes that will start the vehicle every one or two hours within a 24 hour period. 1. Timer Only Mode (factory default) The Automatic Start feature starts the vehicle automatically every one or two hours and runs for the preset Run Time. (15 or 25 min) Auto Start on Timer Mode: 1. Turn Ignition switch Off and wait for 3 seconds. 2. Turn Ignition switch On and Off three times ending with Ignition in Off position 3. Press the Valet switch immediatly after.
Manual Transmission Remote Start Features Model: G5-M/G2-M 1- Tach wire must be connected , The system must learn RPM. 2- Hand brake must be connected. 3- Door trigger must be connected 4- Clutch override installed NOTE: MUST USE RELAY, SEE PAGE 28.
Extended Features Ignition Door Locking For added safety, the Ignition Door Locking feature allows vehicles equipped with power door lock systems to automatically lock the doors when the ignition is turned on. If a door is open when the ignition is turned on, the Ignition Door Locking feature is disabled to protect against locking the keys inside the vehicle. If RPM is selected Doors will lock when engine RPM exceed 2.5 times the idle.
System Installation 1. 2. Thoroughly read and become familiar with the installation instructions before beginning the installation. Review system contents: Main Unit 1 or 2 One-way 5 Button Remote Transmitters (varies by model) 1 or 2 Two-way 5 Button LCD Remote Transmitters (varies by model) Siren Shock Sensor Harnesses • • • • • • • 6-Pin starter harness 20-Pin main harness 4-Pin shock sensor harness 3-Pin door lock harness LED harness Override Switch harness 5 Pin antenna harness 3. 4.
Mounting the Control Unit The control unit must only be mounted in the interior of the vehicle. Do not mount the main unit in the engine compartment. Choose a mounting location that will not be easily accessible to a thief, and will not interfere with the operation of any vehicle components such as foot pedals, steering column, air vents, seat rails, etc. Do not mount the control unit until after setting the internal jumpers and performing a complete operation check of the system.
System Wiring 6-Pin Starter Harness Pin 1 RED WIRE A: Main Power Input A (+). Connect to the battery or constant power wire at the ignition switch with a minimum 25 Amp supply. Remove the fuse until the installation is complete and all wiring is checked. Pin 2 RED WIRE B: Main Power Input B (+). Connect to the battery or constant power wire at the ignition switch with a minimum 25A supply.
Pin 12 GREEN WIRE: Negative Door Input (-). Connect to the door switch circuit wire that shows ground when the door is open. Pin 13 WHITE/BLACK WIRE: Hood/Trunk Pin Input (-). Connect the to the hood/trunk pin switch. The switch must provide a ground output when switch is opened. Pin 14 ORANGE WIRE: Armed Output (-) 500 mA. The Orange wire provides a ground output while armed to activate a relay for starter defeat and anti-grind protection or window rollup module.
4-Pin Black DBP Connector: The plug-in DBP connector port is located on the side of the main module. this DBP port may be used with the optional bypass modules for data bus interface. Jumper Selection Carefully separate the top and bottom halves of the main unit case. Once the cover is removed, the parking light polarity jumper will be visible next to the parking light relay. Set the jumper for the correct polarity output as described below, then reassemble the main unit case. Parking Light Output.
System Programming Entering System Programming This system is compatible with both the LCD two way transmitter or the standard transmitter, all system programming can be performed using either one. To enter System Programming using standard 5 button remote: 1. Turn the ignition switch to the ON position. 2. Within 5 seconds, press the valet switch 5 times. · The siren/horn will provide three chirps/honks, indicating that you have entered Programming. 3.
Programming Branch Table Branch Feature Button 1 (default) Button 2 Button 3 Button 4 1 Arm Mode Manual Arming Passive Arming 2 Auto Rearming Mode Disabled Enabled 3 Arming Chirps Siren Chirps On Siren & Horn Chirps On 4 Ignition Door Locking On Off Set Override Code Data Bus Module Fortin 5 Ignition Door Unlocking Unlock All Unlock Driver Only Off Fortin RF Kit Enable 6 Door Unlock Pulse Single Double 7 Door Lock Pulse Length 1 second 3 seconds 8 Passive Door Locking
2. Auto Rearming Mode. When selected, the system will automatically re-arm 30 seconds after it is disarmed . Restart Mobilink - Reset Mobilink (Galaxy Mobile) module. 3. Arming Chirps. Selects between normal and silent operation. Bypass Data Bus Module - set Bypass module to iDataLink 4. Ignition Door Locking / Override Code Set. This dual program branch selects Ignition Door Locking, and programs the optional Emergency Override Code. Ignition Door Locking.
16. Auxiliary 3 Output Mode. Selects between Channel 3, Factory Rearm output, or third Ignition ouput. 17. Lock After Start. When selected, the doors will automatically lock after remote starting. 18. Lock After Shutdown. When selected, the doors will automatically lock after remote shutdown. 19. Engine Run Time. Selects between 15 or 25 minutes for the remote start run cycle. 20. Automatic Start Mode. Selects between every two hours or every one hour for the automatic engine starting feature.
28. Extended Parking Lights. When selected, the parking lights will remain ON for 30 seconds after disarming the system. 29. Warn-Away Pager Report. When Enabled, Warn-Away report will be sent to the pager. If Disabled no Warn-Away report will be sent to the pager. 30. Anti-Carjack Type. Selects one of three modes for Anti-Carjacking: Active, Passive, or Full-Time. Active. When selected, while igniton is on pressing Button 4 parking light will flash once and anti-carjack feature will be engage.
Relay Diagrams Positive Dome Light Activation Negative Dome Light Activation Positive Horn Honk Negative Horn Honk Starter Defeat/Anti-Grind Negative Glow Plug Page 28 - G5.2W, G2.2W, A4.2W, A1.
Door Lock Diagrams Follow the diagrams below for connecting basic door lock systems. For Two Stage door lock systems (separately unlocks driver and passenger doors) see following pages. Positive Trigger Negative Trigger blue green Reverse Polarity Vacuum UL L Adding Actuators G5.2W, G2.2W, A4.2W, A1.
Two Stage Door Lock Diagrams The Galaxy 5000/2000RS-DBP Series is equipped with a dedicated Passenger Unlock output allowing Two Stage Door Lock operation. When connected as shown below, disarming the system will unlock only the driver’s door. Pressing the disarm button again will unlock all doors. Two Stage Negative Trigger Two Stage Positive Trigger Door Lock Inverter Green Wire Door Lock Inverter Blue Wire Page 30 - G5.2W, G2.2W, A4.2W, A1.
Two Stage Door Lock Diagrams cont’d Two Stage Reverse Polarity Two Stage Adding Actuators G5.2W, G2.2W, A4.2W, A1.
Technical Information FCC ID: OARRXAM2000 This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference.
Wiring Diagram Starter Harness G5.2W, A4.2W G2.2W, A1.
