User Guide Bonded MoCA Network Adapter Model # ECB6250
Table of Contents Table of Contents 1 Getting Started 2 Introduction 2 Package Contents 3 Features 3 Connecting Adapters 4 Connecting the First Adapter 4 Connecting Addititional Adapters 7 Specifications 10 Notices 11 Warranty 11 Important Safety Instructions 11 FCC Class B Equipment 12 Technical Support 14 User Guide | Bonded MoCA Network Adapter | Model # ECB6250 1
Getting Started Introduction Congratulations for purchasing the ScreenBeam ECB6250 MoCA 2.5 Network Adapter. The Adapter is a simple, flexible solution for extending a home network. By leveraging the ubiquity of coaxial cabling within the modern home, the Adapter provides an Ethernet Internet port anywhere a coaxial connection is available. This user manual explains the procedures needed to connect the Adapter.
Getting Started Package Contents • ECB6250 MoCA 2.5 Network Adapter • Coaxial cable • Power adapter • Quick Start Guide • Ethernet cable Requirements • Available coaxial port in installation areas • Available electrical wall socket in installation areas Features • Ethernet port (1.0 gigabit) • Coax In coaxial port (v. 2.5) • MoCA Protected Setup • Power, Coax, and Ethernet LEDs: - Power LED: glows solid green when Adapter is powered up. - Coax LED: glows solid green with connection on the Coax port.
Connecting the Adapters Connecting the Adapter is a relatively simple process. First, connect one Adapter to the broadband modem or router and the coaxial network to establish the Internet signal. Then, additional Adapters can be installed throughout the home or office at any location Ethernet Internet access is needed, and an available coaxial port is available. Connecting the First Adapter The first Adapter must be connected to the broadband modem or router and the coaxial network.
Connecting the Adapters When complete, the setup should look similar to the figure below: Ethernet Cable Ethernet MPS Coaxial Cable Power Coax In Power Coaxial Outlet Coax ECB6250 Power Outlet Ethernet Port of Modem/ Router Power Adapter If Coaxial Port is Being Used buy Another Device: 2-Way Splitter OUT IN To Coaxial Port on Device To Coax In Port on ECB6250 2-WAY SPLITTER OUT From Coaxial Outlet The Internet signal is now being delivered across the coaxial network.
Connecting the Adapters You will be asked to login. The user name is “admin" and the password is “actiontec”. Once you have enabled MoCA encryption, you can use the MPS push button to synchronize the encryption password on each MoCA 2.5 adapter connected via coaxial cable. Using a Coaxial Splitter If the coaxial port is already being used by another device (a set-top box, for example), follow these steps: 1. Disconnect the coaxial cable from the connected device.
Connecting the Adapters If necessary, additional Adapters can be placed at locations around the home or office that need an Ethernet Internet connection, but currently only have a coaxial port. To connect additional Adapters: 1. Connect a coaxial cable to a nearby coaxial outlet. 2. Connect the other end of the coaxial cable to the Coax In coaxial port on the side of the Adapter. 3. Connect one end of an Ethernet cable to the Ethernet port of the modem/router. 4.
Connecting the Adapters When complete, the setup should look similar to the figure below: Ethernet Cable Ethernet MPS Coaxial Cable Power Coax In Power Coaxial Outlet Coax ECB6250 Power Outlet Ethernet Port of Modem/ Router Power Adapter If Coaxial Port is Being Used buy Another Device: 2-Way Splitter OUT IN To Coaxial Port on Device To Coax In Port on ECB6250 2-WAY SPLITTER OUT From Coaxial Outlet The device connected to the Ethernet port is now connected to the Internet via the coaxial ne
Connecting the Adapters If the coaxial port is already being used by another device (a set-top box, for example), follow these steps: 1. Disconnect the coaxial cable from the connected device. Leave the other end connected to the coaxial wall outlet. 2. Get a 2-way coaxial splitter (not included). 3. Connect the coaxial cable disconnected in step 1 to the single (“In”) port on the coaxial splitter. 4. Connect a coaxial cable (not included) to one of the dual (“Out”) ports on the coaxial splitter. 5.
Specifications Model Number ECB6250 (MoCA 2.5 Network Adapter) IP LAN MoCA (v. 2.5; up to 2.5 Gbps throughput) LAN Ethernet Port 10/100/1000 (1) LAN Connections Coax In Frequency Range - Extended D-band: 1125MHz ~1675MHz; LED Indicators Power Power, Coax External, 5V DC, 2A, 1.
Notices Warranty This product has a one-year Limited Hardware Warranty and 90-day free software updates from date of purchase. Local Law This Limited Warranty Statement gives the customer specific legal rights. The customer may also have other rights which vary from state to state in the United States, from province to province in Canada, and from country to country elsewhere in the world.
Notices • Use only the power cord and batteries indicated in this manual if applicable. Note: you may need to reword for batteries or adapters. • Do not dispose of batteries in fire, as they may explode – check with local codes for possible special disposal instructions if applicable. Coaxial Cable If applicable, the coaxial cable screen shield needs to be connected to the Earth at the building entrance per ANSI/NFPA 70, the National Electrical Code (NEC), in particular Section 820.
Notices Declaration of Conformity for Products Marked with the FCC logo–USA Only This device complies with Part 15 of the FCC Rules license-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause harmful interference; 2. This device must accept any interference received, including interference that may cause undesired operation of the device.
Contact Information For questions regarding your product or the FCC/Industry Canada declaration, contact: ScreenBeam, Inc. 220 Devcon Drive, San Jose CA 95112 Technical Support Go to retailsupport.screenbeam.
