SCOTT SCALE USER MANUAL All rights reserved © 2017 SCOTT Sports SA Distribution: SSG (Europe) Distribution Center SA, P.E.D. Zone C1, Rue du Kiell 60, 6790 Aubange, Belgium v6.4/040717 WWW.SCOTT-SPORTS.COM SCOTT Sports SA Route du Crochet 17, CH–1762 Givisiez Phone: +41 26 460 16 16 | Fax: +41 26 460 16 00 Email: scottsupport@scott-sports.com W W W. S C O T T- S P O R T S .
••CONTENTS SCOTT SCALE 3 . . . . . . . . . . . . . . . . . . . . . . . 04 Scale Concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 04 Geometry/Technical Data Scale 3 700 . . . . . . . . . . . . . . . . . . . . . 05 WWW.SCOTT-SPORTS.COM Geometry/Technical Data Scale 3 900 . . . . . . . . . . . . . . . . . . . . . 06 RIDELOC . . . . . . . . . . . . . . . . . . . .
••GEOMETRY/TECHNICAL DATA SCALE 3 700 SCOTT SCALE 3 ••SCALE CONCEPT From the Carbon fiber to the manufacturing process to the final result- the new Scale has been completely redesigned. The result: a new benchmark for race hardtail frames. The Scale RC 700 SL weighs in at only 849 grams. The incredible lightweight frame characteristics and two dedicated frame platforms for 1x and 2x drivetrains lift the standard of hardtail mountain bikes to a new level.
••GEOMETRY/TECHNICAL DATA SCALE 3 900 •• IMPORTANT! Seatpost Diameter 31.6mm Seattube clamp 34.9 Headset bearings: 51.9x40x8 45 ° x 45 °/ 41.8x30.5x8 45 ° x 45 ° Fork travel 100mm BB housing BB PF92 Front derailleur Shimano high direct mount side swing (none RC models only) Additional parts needed Chainring size 38T max Max tyre width 2.3/57mm Please note: Tire sizes often vary from brand to brand.
••BASIC SET-UP OF FORKS ••SAG Recommended tools for the shock setup: Your SCOTT bike will be supplied with a SAG tool to help set up your bikes suspension, these SAG tools can be easily clipped on the fork body and Fork dust seal. -- The SAG tool that came with your bike. *Fox forks only -- A shock pump with a special air valve connector (not supplied with this bike), this will help stop air from escaping while removing the pump from the shock valve.
••REBOUND FORK SET-UP If your dropout needs to be replaced, we recommend this work should be carried out by your local SCOTT dealer as the rear derailleur may need adjustment, failure to adjust this correctly may result in accident or damage to your bike. “Rebound” describes the speed the fork returns back to its original length after absorbing an obstacle, setting of this is very important for the handling and correct function of the bike.
••CABLE GUIDES AND CABLING. ••BB STANDARDS/FD MOUNTING DETAILS On the carbon SCOTT Scale the cable guides on the headtube can be changed if required so different cable configurations can be used, the inside of the cable guide is stamped with a number or numbers, these numbers dictate what cables can be used, these are the same for left and right.
••GEOMETRY/TECHNICAL DATA SCALE SCOTT SCALE 2 SCALE 700 ••SCALE CONCEPT A HEAD TUBE ANGLE Scale is the result of research and development based on the feedback from the SCOTTODLO Racing Team searching for one of the lightest cross country racing frames in the market. SCOTT’s focus was not only on creating a lightweight frame, but one that was also a stiff and easy to handle racing frame. S 69.0 ° Scale 700 / Plus: 31.6mm (27.5”), Scale 900: 34.9mm (29”) Seattube clamp Headtube diameter 100.
••BB STANDARDS/FD MOUNTING DETAILS Scale is available for PressFit 92 Cartridges (PF92). PF BB 92 has a housing width of 92mm (Scale 700) or 89.5mm plus a 2.5mm additional washer (Scale 900, Scale Plus) with an inner diameter for the cartridges of 41mm. Scale 700 (27.05”) FD The front derailleur (FD) fixation for Scale 700 is a direct mount system. It is made for Shimano E-Type derailleurs or SRAM S3 assembly. For Scale Plus the FD fixation is E-Type with 3mm outboard to match with rear hub boost standard.
Ritchey WCS Carbon Zero Tapered PF 50-61mm 18mm UD PRD 13636 Ritchey PRO Tapered PF 50-61mm 12.9mm PRD 13640 Please note that the outer housing of the FD and RD cables will stop at the cable stop/port on the front end of the down tube. It is also possible to use forks with a standard 1 1/8” steerer tube when using a reducer headset such as e.g.
••SEATTUBE CLAMP ••REAR DISC BRAKE MOUNT Please make sure to only use a seatclamp with an inner diameter of 34.9mm (Scale 700 / Plus) or 38.2mm (Scale 900) and please note the maximum tightening torque on the fixing bolt of 5Nm/44 in/lbs The rear disc brake on Scale is Postmount (PM) Standard on the left chainstay and optimized for 160mm/6” rotors, so the calliper can be mounted directly without adapters on the Postmount fixation.
GUARANTEE ON SCOTT BIKES •• WARNING! SCOTT Sports SA is not responsible or liable for any injury caused by any missing compliance with these instructions, particularly but not limited to misuse, incorrect maintenance, incorrect set-up and handling, neglect or abuse. Failure to follow these instructions can result in component failure, serious personal injury. Component failure can lead to loss of control of the bicycle and result in serious personal injury.
