i-XCR 100 MP3/WMA/SD/MMC/USB/AUX CAR RADIO with iPod Docking Station FM Stereo/MW Radio RDS (Radio Data System) Function Copy and Erase Functions Detachable front panel with touch controls 4x40 W Music Power USER MANUAL AND INSTALLATION INSTRUCTIONS
CONTENTS CONTENTS..........................................................................................................................................................................................1 ACCESSORIES....................................................................................................................................................................................2 PRECAUTIONS.......................................................................................................
ACCESSORIES Mounting Bracket (Half Sleeve) X1 Self-tapping Screw X1 Removable Trim Ring fixed on the unit X1 Hex Nut X1 Small metal Strip X1 Release Key X2 Plain Washer X1 Spring Washer X1 USB Adaptor Cable X1 i-XCR 1 0 0 MP3/WMA/SD /MMC/USB/AUX CAR RADIO with iPod DOCKING FM Stereo Radio RDS (Radio Data System) F unction Copy f unction Detachable p anel with touch controls 4x40 W High Power Output USER MANUAL AND INSTALLATION INSTRUCTIONS ISO Wire Connector X1 Protective Case X1 Removable fro
PRECAUTIONS This unit is designed and manufactured with the user’s safety in mind, however any improper use or operation may result in certain dangers. It is therefore highly recommended to read this manual thoroughly and adhere to the following precautions. SAFETY PRECAUTIONS To prevent an electrical shock, do not open the housing of the unit. In any case of malfunctioning, only have the unit serviced by an approved and qualified service center.
INSTALLATION Notes: - Choose a mounting location where the unit will not interfere with the driver’s ability to drive the car. - Before completing the final installation of the unit, connect the wiring and make sure that the unit works properly. - Consult your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle. - Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a sudden stop, like an emergency stop.
4. Mount the sleeve by inserting the sleeve into the dashboard opening and bend out the tabs located around the sleeve with a screwdriver. Not all tabs will be able to make contact, so examine which ones will be most effective. To secure the sleeve in place, bend out the appropriate tabs so that they hold the sleeve in place in the dashboard. 5. Connect the wire harness and the antenna (see “Wiring diagram” on page 8) to the car radio, being careful not to pinch any wires or cables. 6.
8. Reconnect the cable to the vehicle battery's negative (-) terminal. Then replace the outer trim ring and install the unit's front panel (see the section 'TO ATTACH THE FRONT PANEL'). Dismantling the unit 1. Make sure the ignition is turned off, and then disconnect the cable from the vehicle battery's negative (-) terminal. 2. Press the REL ( ) button to remove the front panel. 3. Lift the top of the outer trim ring then pull it out to remove it. 4.
USING THE DETACHABLE FRONT PANEL REMOVING THE DETACHABLE FRONT PANEL The front panel of the unit may be removed as a theft deterrent. After removing the front panel, use the case provided to prevent the front panel from getting damaged. 1. Press the REL button to release the front panel. 2. Gently push the front panel towards the right side before pulling it out from the unit. 3. Store the front panel in the protective case.
WIRING DIAGRAM Many vehicles are fitted with ISO connectors behind the dashboard, which makes it easier to connect your car radio. These connections can be found in the dashboard where the car radio will be fitted. Use these cables to connect the car radio. Should your car not be fitted with these ISO connectors, we strongly advise you to consult your car dealer or a specialist to obtain the right adaptor.
OPERATIONS LOCATION AND FUNCTIONS OF KEYS Front panel: 1 Car radio after removing the front panel: 3 4 5 6 7 8 2 24 25 26 21 9 22 23 10 11 12 13 14 15 16 17 18 19 20 27 28 29 Description Item Description 1 2 REL ( ) LCD display 3 AS/PSּID3 4 MODE 5 AF 6 PTY/IX-BASS 7 TA/COPY 8 MENU VOLUME/ PUSH SELECT 9 System Touch & Touch hold Tuner Touch Preset Scan IX-BASS USB, Card Touch & Touch & Touch hold hold Press to release the front panel Dot matrix / colour Auto Store ID3 disp
10 11 12 /MUTE BAND I<< 13 >>I 14 1/►II 15 2/INT 16 17 18 19 3/RPT 4/SHF 5/F6/F+ 20 DISP 21 AUX INPUT 22 AUX/USB port compartment 23 24 25 26 27 28 29 Turn on/Mute Turn off FM1/2/3/MW In system menu: Next/Previous menu option Auto seek up/ down Search file/folder Erase file Search Manual seek up/ down Next/ Previous file Fast forward/ backward Next/ Previous file Memorize station Play/Pause Track Introduction Repeat one Random all Next/ Previous folder Preset 1 Preset 2 Preset
GENERAL OPERATIONS Reset the unit When operating the unit for the first time, after replacing the car battery or changing the connections, you must reset the unit. 1. Turn off the unit power. 2. Press the ( ) button and remove the front panel, then press the RESET button with a ballpoint pen or similar object to restore the unit to the original factory settings.
Selecting playback mode When the unit is switched on, touch the MODE button repeatedly to select one of the following modes: TUNER, USB (with USB device inserted), SD/MMC (with SD/MMC card inserted), iPod (with iPod inserted), AUX in mode. Last position memory feature - During iPod, USB device or SD/MMC card playback, if you turn off the unit and then switch it on, the unit will resume playing from the point that it was interrupted.
In manual search mode, if neither of the two buttons is used within 5 seconds, the radio will go to automatic search mode automatically. The message “Auto Seek” appears on the LCD display. To store / recall preset radio stations You can store up to a total of 24 radio stations in the memory (manually or automatically). - To store a station: - Select a band (if needed) - Select a station using the I<>I buttons (refer to auto / manual tuning). - Touch a preset button (1-6) for at least 2 seconds.
RDS (RADIO DATA SYSTEM) OPERATIONS The RDS functions are: PI (Program identification): code for identifying the radio station. PS (Program service): name of the radio station. PTY (Program type): type of program (such as news, pop music, sports etc.) TP (Traffic program): code indicating a station broadcasting traffic information. TA (Traffic announcement): function allowing the broadcasting of traffic information.
Music Group Pop Music, Rock Music Easy Music, Light Music Classics, Other Music Jazz Music, Country M Nation M, Oldies M Folk Music Speech Group News, Affairs, Information Sport, Education, Drama Culture, Science, Varied Weather, Finance, Children Social, Religion, Phone In Travel, Leisure, Document, Alarm test, Alarm! Note: Certain types of program are stored by default under the following preset numbers: M1-News, M2-Information, M3-Pop Music, M4-Sport, M5-Classics, M6-Finance.
Installing an iPod 1. Push down the lever to release 2. Pull out the iPod loader. the iPod loader. 3. Press the button to unlock 4. Eject the loader the iPod holder. completely using the tab. 5. Hold down the iPod buttons 6. Push the loader to insert the 7. Press the two adjustable 8. Push the iPod loader back which lock the iPod and insert an iPod into the unit until it stops. sides of the iPod holder to into the unit until a click iPod. Release the buttons to fix hold the iPod firmly in place.
Removing an iPod Follow the previous steps from 1 to 4. 5. Press the iPod connector lock 6. Push the loader until it stops. buttons to release the iPod. Remove the iPod. 7. Press the two adjustable 8. Push the iPod loader into sides of the iPod holder on the unit until a click sound is both sides until it stops. heard. Charging an iPod While an iPod is connected to the unit, the iPod will be automatically charged as long as the vehicle's ignition key is turned to ACC or ON.
Displaying music information During playback, touching the AS/PSּID3 button repeatedly to display the music information including song/artist/album name on the unit’s LCD display. Note: Some characters (such as accents) may not be displayed properly. Searching for a song During iPod playback, touch the BAND button to enter the searching Mode. Touch it repeatedly to select an option: Playlist/Artist/Album/Song/Genre and then press the VOLUME/PUSH/SELECT button to confirm.
SD/MMC MEMORY CARD OPERATIONS Using an SD/MMC card: Remove the front panel. When you insert an SD/MMC card into the memory card slot, the player will read the SD/MMC card automatically. If you insert a USB device into the USB port while reading an SD/MMC card, the unit will play the USB device automatically. You can touch the MODE button to select SD/MMC mode. For more details on SD/MMC memory card playback operations, refer to the section “MP3/WMA FILES OPERATIONS”.
MP3/WMA FILES OPERATIONS Touch the MODE button to select the USB or SD/MMC mode if both a USB device and SD/MMC card are inserted into the unit. Playing/Pausing - During playback, touch the button to interrupt playback. Touch again to resume playback. Playing the previous/ next track - During playback, touch the >>I button to play the next track. The track number shows on the LCD display. - During playback, touch the I<< button to play the previous track. The track number shows on the LCD display.
How to select a file in MP3/WMA mode: During playback, touch the BAND button to enter the search mode. The message “Navigate” is displayed. Rotate the VOLUME/PUSH SELECT button to search the desired folder or sub-folder and then press it to confirm. Repeat this step to search for and play a desired song. ID3 information display This unit makes it possible to display ID3 tag information recorded with the MP3/WMA file.
• Do not switch to another mode. • Do not turn the unit off or switch the vehicle’s engine off. Erasing files 1. Insert a USB device or SD/MMC card into the unit and then use the MODE button to select the source that you intend to erase a music file from. 3. Select the song you want to erase. 4. Touch and hold the BAND button to enable the erase function. The message “ERASE” will be displayed. 5. Press the VOLUME/PUSH SELECT button to enter the erase mode. “ ” is displayed. 6.
TECHNICAL SPECIFICATIONS 1. GENERAL Power Supply ................................................................................................................. DC 11 - 14 Volts, negative ground Unit Dimensions ............................................................................................................. 178(W) x160(D) x 50(H) mm Tone Controls ................................................................................................................. - Bass (at 100 Hz) ±10 dB .........
TROUBLESHOOTING Symptom No power No sound Cause The car ignition switch is not on. The connections are not correct. A fuse has blown in the vehicle. The fuse at the back of unit has blown. Volume is at minimum. The mute function is activated. The wiring is not properly connected. Solution Turn the ignition key to the accessory position until the unit is switched on. Check the connections. Check the vehicle fuses. Adjust volume to a desired level. Switch off the mute function.
If at any time in the future you should need to dispose of this product, please note that waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice (Waste Electrical and Electronic Equipment Directive).
