i-CSX 15 DUAL ALARM CLOCK FM/AM PLL RADIO WITH iPod/iPhone DOCKING STATION AND AUTOMATIC TIME SETTING SYSTEM Instruction Manual
PRECAUTIONS Follow the advice below for safe and appropriate operations. PLACEMENT . Do not use the unit in places which are extremely hot, cold, dusty, or humid. . Place the unit on a flat and even surface. . Do not restrict the air flow of the unit by placing it in a place with poor air flow, by covering it with a cloth, or by placing it on a carpet. . Do not place naked flame sources such as lighted candles on the apparatus. . Use the apparatus only in moderate climates (not in tropical climates). .
TABLE OF CONTENTS PRECAUTIONS.................................................................................................................................................. 1 TABLE OF CONTENTS...................................................................................................................................... 2 BOX CONTENTS................................................................................................................................................ 2 LOCATION OF CONTROLS.
19 10 22 4 24 25 4 7 16 17 26 5 6 14. MEM/SET (Memory/Clock set) button 15. DIMMER button 16. Headphones jack 17. Clock back up battery compartment 18. SLEEP button 19. ALARM 1/2 LED indicators 20. PRESET - / (Shuffle) button 21. PRESET + / (Repeat) button 22. FM STEREO LED indicator 23. NAP button 24. DST (Daylight Saving Time) ON/OFF switch 25. RESET button 26. AM antenna socket 1. Docking station for iPod/iPhone 2. button 3. ALARM SET 1/2 button 4. Speakers (2 x) 5. AUX IN jack 6.
POWER SUPPLY Power supply for the unit Insert the AC/DC adapter power cord into the AC mains outlet with a 100-240V AC ~ 50/60Hz power source and the other end into the DC IN 10V jack at the back of the unit. Installing the clock back up battery The clock time can be maintained during a power failure by using 2 x AA/ LR06 batteries (supplied). Battery insertion 1. Open the battery compartment on the back of the unit by pressing on the battery compartment catch whilst removing it. 2.
Enable/ Disable the alarm function 1. Press the AL1 or AL2 button repeatedly to enable or disable the alarm function and select the following alarm modes: buzzer ( ), radio ( ), iPod or iPhone ( ). The corresponding indicator (AL1 or AL2) will light up on the LED display. 2. When the alarm function is on and the preset alarm time is reached, the alarm will sound in the selected alarm mode for one hour. 3. To stop the alarm, press the button. The alarm will sound again at the same time the next day.
VOLUME control Press the VOLUME ▲/▼ buttons to adjust the volume level. Connecting headphones Plug the headphones (not supplied) into the headphones jack at the back of the unit for private listening. The speaker output will be shut off automatically. DIMMER control Press the DIMMER button to select the brightness of the display (high or low). DISPLAY function In radio mode, the clock is always displayed. You can press the SNOOZE/DISPLAY button to display the frequency for 5 seconds.
PLAYING AN iPod/iPhone AND CHARGING THE INTERNAL iPod/iPhone BATTERY Installing an adapter on the iPod/iPhone docking station 1. Remove the cover of the docking station at the top of the unit and insert the adapter (supplied with your iPod/iPhone) into the docking station with the two tabs facing forwards. 2. To remove the adapter, press the back of the adapter and pull it up. Listening to your iPod/iPhone 1.
AUX IN FUNCTION This unit has an AUX IN jack which allows you to connect your external audio devices such as MP3 players or an earlier iPod model. 1. Connect a 3.5 mm stereo connection cable (not supplied) to the AUX IN jack on the back of the unit and the phones/line out jack on your external audio device. 2. When the unit is switched on, press the FUNCTION button to select AUX mode. 3. Operate your external audio device as usual to select and play the music. 4.
TROUBLESHOOTING GUIDE Problems Recommendations 1.The player or display does not work properly. 1.1 Press the button to go to standby mode and press it again to turn on the unit. 1.2 Press the RESET button with a sharp object to reset the unit. 1.3 Reset the unit by unplugging the AC power cord for a few seconds, then plug it back in. 2. No sound, poor sound. 2.1 Check the cable connections. 2.2 Use the FUNCTION button to select the correct mode. 3. Noise or distorted sound in radio mode. 3.
