Schloss HD7000B AFTERMARKET STEREO INSTALLATION KIT & HARNESS FOR SELECT HARLEY-DAVIDSON 2006-2013 FLEX STREET GLIDE, 1996-2013 FLT ELECTRA GLIDE & 1998-UP FLT ROAD GLIDE MODELS (WITH FACTORY-EQUIPPED RADIO) PARTS INCLUDED: fats 1. DASH KIT BRACKET (1) Mounting Panel (2) Left & Right Mounting Brackets (4) Screws (bracket attachment) (2) Spacers (*Road Glide models only} 2. WIRE HARNESS 3.
FACT STEREO REMOVAL 2006-2013 FLEX STREET GLIDE 1996-2013 FLT ELECTRA GLIDE 0 Drape a protective cloth over the front fender. Extract (3) T-27 Tory bolts from | bottom edge of windshield. Carefully lift away windshield, store in a safe location and replace the middle Tory bolt for support during the remaining removal steps. Extract (2) T-27 Tory bolts from outer side of the fairing {under mirrors). Extract (2) T-27 Tory bolts from inside the fork tubes {facing forward).
FACT STEREO REMOVAL While supporting the outer fairing, remove the middle windshield bolt, lift away and | Unbolt and remove inner fairing support unplug headlight to remove | brackets from each side (3/16" hex & fairing shell. Store fairing ina | T-25 Tory screws) Note that the Tory safe place until re-assembly. | screw is also a shared speaker screw. © Extract (2) %4' 6mm hex bolts from each side of the radio housing.
FACTORY STEREO REMOVAL 1996-UP FLT ROAD GLIDE oO Drape a protective cloth over the front fender. 0 DO NOT remove the windshield on Road Glide models Use a 7/16" socket or box wrench to remove {2) nuts that hold the each turn signal at the lower fairing. Remove the metal strap under the nuts, and push the studs out to remove the signals. CAUTION: Do not let tum signals drop or dangle. Extract {2) T-25 Tory bolts from outer left and right sides of the fairing.
FACT STEREO REMOVAL 0 Have a helper hold on the outer fairing and extract the last (2) T-25 Tory bolts from the upper fairing near the speaker grilles. © Carefully lift fairing at headlights to release support hooks, unplug headlights and remove. Store fairing in a safe place until reassembly. NOTE!: Be sure to reattach support hooks during re installation. o Extract (2) 6mm hex bolts from each side of the radio housing.
KIT ASSEMBLY REMOVE SLEEVE FROM AFTERMARKET STEREO 1. Locate the locking mechanism on your DIN stereo sleeve {typically) on the side. 2. Slip mounting sleeve towards rear of stereo and remove (Figure 1). FIGURE 1 1ST-DIN MOUNT ONLY 1. Attach the 7423 and 7424 side brackets to the 7422 front panel using the hardware supplied with the kit (Figure 2). 2. Remove supplied trim ring and sleeve from new stereo. 3.
WIRING CONNECTION 1. Match and connect the wires from the new stereo to the Harley Davidson connector supplied with the HD7000B kit (sea Figure 2 & Wiring Color Codes ballgown. 2. Connect the radio end and the Harley Davidson connector (Figure 2). 3. Connect the Antenna lead to the back of the stereo. 4, Test stereo’s functionality. «< To motorcycle shames HD70008B HARNESS CONNECTOR «< Joyrode 0 3.
hl NAL HANDLEBAR CONTROL WIRING market Ha Control Interface sold separately) Right Hand Black Controls Connector —— BROWN/WHITE BROWN/WHITE WHITEWATER ‘GRAY WHITE WHITENING PINWHEEL — —— ULTRAVIOLET 'VIOLET/BLACK Cut BEFORE wires Jon! GREENGAGE GRAY/GREEN \ — GREEN/BLUE -GREEN/BLUE PINWHEEL PINKERTON —) 34 —— BROWN/BLACK BROWN/BLACK | Loft Hand = Cut & ground Gino HANDLEBAR = = SIDE of wire FIGURE 3 STANDARD pe pw HANDLEBAR CONTROLS ~— {All models except FLHTP-FRG) To radio shames pas) fA = & Right Hand Bla
