manual

Read pages 3-6
for kit assembly.
Read pages 3-6
for kit assembly.
"B2"
BRACKET
USE HOLE #2
"B2" SOPORTE
USA ABERTURA
NO. 2
"D2" BRACKET
USE HOLE #2
"D2" SOPORTE USA
ABERTURA NO. 2
SPACER
EL ESPACIO
CUT OFF PINS (TWO SPACERS)
CORTA LAS CLAVIJAS
(DOS ESPACIADORES)
SPACER
EL ESPACIO
CUT OFF TABS
(TWO BRACKETS)
ROMPE LAS
LENGUETAS (DOS
SOPORTES)
TOP
TOPE
FRONT OF KIT
FRENTE DE
ESTUCHE
"B1" BRACKET USE HOLE #4
"B1" SOPORTE USA ABERTURA
NO. 4
"A1" BRACKET USE HOLE #3
"A1" SOPORTE USA
ABERTURA NO. 3
"C2" BRACKET USE HOLE #3
"C2" SOPORTE USA ABERTURA NO. 3
RIGHT SIDE
LADO DERECHO
LEFT SIDE
LADO IZQUIERDA
"D2" BRACKET USE HOLE #4
"D2" SOPORTE USA ABERTURA NO. 4
Read pages 3-6
for kit assembly.
FRONT OF KIT
FRENTE DE
ESTUCHE
"B1" BRACKET USE HOLE #1
"B1" SOPORTE USA ABERTURA
NO. 1
"A1" BRACKET USE HOLE #1
"A1" SOPORTE USA
ABERTURA NO. 1
"C2" BRACKET USE HOLE #1
"C2" SOPORTE USA ABERTURA NO. 1
RIGHT SIDE
LADO DERECHO
LEFT SIDE
LADO IZQUIERDA
"B2" BRACKET USE HOLE #1
"B2" SOPORTE USA ABERTURA NO. 1
25
1987-91 Pontiac Bonneville
RADIO REMOVAL:
1. Place the gear selector in low gear to gain clearance.
2. Gently pull on the edges of the radio panel to release
the panel clips and remove the panel.
3. Remove the two screws from
the bracket above the radio.
4. Remove one screw from the
rear support bracket (access
through the ashtray cavity).
5. Insert a thin blade screwdriver
into the two slots below the
radio and pry the metal
retaining tabs upward
to release them.
6. Slide the radio out of the cavity,
disconnect all the electrical
connections, then remove the radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1984-88 Pontiac Fiero
RADIO REMOVAL:
1. Remove the four screws from the radio trim panel.
2. Pull the panel up and outward toward the right.
3. Remove the four screws from the radio brackets and pull the radio out of the cavity.
4. Disconnect the antenna, speaker leads and all the electrical connections, then remove the radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1993-02 Pontiac Firebird
RADIO REMOVAL:
1. Using a panel removal tool/screwdriver, carefully release
the fastening clips from around the perimeter of the radio
trim bezel and remove the bezel.
2. Extract the four screws securing the radio to the dash, pull the radio from the cavity, unplug all the
connectors, and remove the radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.