manual

Read pages 3-6
for kit assembly.
RIGHT SIDE
LADO DERECHO
LEFT SIDE
LADO IZQUIERDA
"C2" BRACKET
USE HOLE #3
"C2" SOPORTE USA
ABERTURA NO. 3
"B1" BRACKET
USE HOLE #4
"B1" SOPORTE
USA ABERTURA
NO. 4
Read pages 3-6
for kit assembly.
RIGHT SIDE
LADO DERECHO
LEFT SIDE
LADO IZQUIERDA
"C1" BRACKET USE HOLE #3
"C1" SOPORTE USA
ABERTURA NO. 3
"B1" BRACKET
USE HOLE #4
"B1" SOPORTE USA
ABERTURA NO. 4
FRONT OF KIT
FRENTE DE
ESTUCHE
FRONT OF KIT
FRENTE DE
ESTUCHE
"C2" BRACKET USE HOLE #3
"C2" SOPORTE USA ABERTURA NO. 3
"B2" BRACKET USE HOLE #4
"B2" SOPORTE USA ABERTURA NO. 4
Read pages 3-6
for kit assembly.
FRONT OF KIT
FRENTE DE
ESTUCHE
RIGHT SIDE
LADO DERECHO
LEFT SIDE
LADO
IZQUIERDA
"C1" BRACKET USE HOLE #3
"C1" SOPORTE USA ABERTURA NO. 3
"B1" BRACKET USE HOLE #3
"B1" SOPORTE USA ABERTURA NO. 3
20
1986-94 Chevrolet S-10 Blazer
1986-93 Chevrolet S-10 Pickup
1986-94 GMC S-15 Jimmy
1986-93 GMC S-15 Pickup
1991-94 Oldsmobile Bravada
RADIO REMOVAL:
1. Open the glove box door and remove
the two screws from the
radio trim panel.
2. Remove the ashtray
and remove one
screw from the
upper inside corner
of the recess and
one from the lower inside corner. Remove the trim panel.
3. Remove the two screws which secure the radio to the dash, disconnect the wiring, and remove the radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1982-85 Chevrolet S-10 Blazer, Pickup
1982-85 GMC S-15 Jimmy, Pickup
RADIO REMOVAL:
1. Remove the four screws from the radio trim panel.
2. Remove the single
screw from the lower
right corner of the
instrument cluster
trim panel.
3. Remove the radio
trim panel.
4. Remove the four screws
retaining the radio/
dummy panel. Pull the
radio out of the cavity,
disconnect the antenna,
speaker leads, and all the
electrical connections,
then remove the radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.
1988-95 Chevrolet Van, Full Size
1988-95 GMC Van, Full Size
RADIO REMOVAL:
1. Remove the two screws from the top inside of the ashtray area.
2. Remove the two screws from the bottom front of the engine hump cover, pull the cover off and remove
the electrical harnesses. Then remove the engine hump cover/shell.
3. Remove the single screw from the right side of the chassis securing the rear support bracket to the
fi rewall. (A 10mm socket
wrench will be needed).
4. Carefully snap off the
radio trim piece.
5. Remove the two
screws (10mm )
securing the radio to
the dash, one at
each side of the chassis.
6. Pull the radio out of the
cavity, remove the antenna
lead, disconnect the wire
harnesses and remove the radio.
USE THE SHADED BRACKETS & THE INDICATED HOLE LOCATIONS. CUT OFF THE REMAINING BRACKETS & DISCARD.
Usa los soportes asombrados y las localizaciónes de aberturas indicadas. Corta los soportes que sobran y desechalas.